Make it possible to activate some additional kernel debug options.
This can be used to debug some problems in kernel drivers.
Signed-off-by: Hauke Mehrtens <hauke.mehrtens@intel.com>
Reviewed-by: Alexandru Ardelean <ardeleanalex@gmail.com>
The kernel kernel address sanitizer is able to detect some memory
bugs in the kernel like out of range array accesses.
Signed-off-by: Hauke Mehrtens <hauke.mehrtens@intel.com>
Reviewed-by: Alexandru Ardelean <ardeleanalex@gmail.com>
The kernel Undefined Behavior Sanitizer is able to detect some memory
bugs in the kernel like out of range array accesses.
Signed-off-by: Hauke Mehrtens <hauke.mehrtens@intel.com>
Reviewed-by: Alexandru Ardelean <ardeleanalex@gmail.com>
This option has now a different dependency and can be activated, set a
default value.
Fixes: 20b5a4ca01 ("kernel: bump 4.19 to 4.19.101")
Signed-off-by: Hauke Mehrtens <hauke.mehrtens@intel.com>
Tested-by: Alexandru Ardelean <ardeleanalex@gmail.com>
So far, the state of status LEDs is set up in 01_leds for many devices
in kirkwood target. As those LEDs are also controlled by diag.sh,
exposing them to the user via uci config by default seems not helpful
and might even have confusing results for the user.
Thus, remove the ucidef_set_led_default setup for power/status LED, but
do not touch the rest where user control is actually a feature.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This adds the default-state = "on"; statement for the power or
primary status LED in DTS on kirkwood. This will ensure that this
LED will be lit up very early in the boot process (i.e. before
diag.sh is executed) and thus will provide an additional hint to the
user when problems arise during early boot process.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This commit removes the target-specific diag.sh script. This way, the
generic one is used for the target, which uses DT-aliases to specify the
LEDs used.
Generic diag.sh allow to use different LEDs to indicate different states.
Non-red status LEDs for indicating boot and a running system.
Where possible, the red or orange LEDs are used to indicate failsafe
mode and a running upgrade.
Compile-tested: all target devices.
Run-tested: CheckPoint L-50
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
[remove unrelated cosmetic changes, rename some labels, add pogo_e02]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Specification:
- 550/400/200 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 4x 10/100 Mbps Ethernet, with passive PoE support on LAN1
- 2T2R 2,4 GHz (AR9344)
- built-in 4G/3G module (example: Quectel EC-25EU)
- internal microSD slot (spi-mmc, buggy and disabled for now)
- RS232 on D-Sub9 port (Cypress ACM via USB, /dev/ttyACM0)
- RS422/RS485 (AR934x high speed UART, /dev/ttyATH1)
- analog 0-24V input (MCP3221)
- various digital inputs and outputs incl. a relay
- 11x LED (4 are driven by AR9344, 7 by 74HC595)
- 2x miniSIM slot (can be swapped via GPIO)
- 2x RP-SMA/F (Wi-Fi), 3x SMA/F (2x WWAN, GPS)
- 1x button (reset)
- DC jack for main power input (9-30 V)
- debugging UART available on PCB edge connector
Serial console (/dev/ttyS0) pinout:
- RX: pin1 (square) on top side of the main PCB (AR9344 is on top)
- TX: pin1 (square) on bottom side
Flash instruction:
Vendor firmware is based on OpenWrt CC release. Use the "factory" image
directly in GUI (make sure to uncheck "keep settings") or in U-Boot web
based recovery. To avoid any problems, make sure to first update vendor
firmware to latest version - "factory" image was successfully tested on
device running "RUT9XX_R_00.06.051" firmware and U-Boot "3.0.2".
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add support for RS485 tranceiver with transmit/receive switch hooked
to a RTS GPIO pin.
Use the 'rts-gpios' and 'rs485-rts-active-low' properties as described
in devicetree/bindings/serial/rs485.yaml.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This adds support for the various clones of the TL-WA830RE recently
supported in fb99ac6807 ("ath79: add support for TP-Link TL-WA830RE v1"):
- tplink,tl-wa701nd-v1
- tplink,tl-wa730re-v1
- tplink,tl-wa801nd-v1
- tplink,tl-wa830re-v1 (already supported)
- tplink,tl-wa901nd-v1
Since these devices are 100%-clones in ar71xx, this patch adds all
of them without run-testing (as this has been done for TL-WA830RE v1).
Specifications:
- SOC: Atheros AR7240
- CPU: 400MHz
- Flash: 4 MiB (Spansion S25FL032P)
- RAM: 32 MiB (Zentel A3S56D40FTP-G5)
- WLAN: Atheros AR9280 bgn 2x2
- Ethernet: 1 port (100M)
Flash instructions:
- install from u-boot with tftp (requires serial access)
> setenv ipaddr a.b.c.d
> setenv serverip e.f.g.h
> tftpboot 0x80000000 \
openwrt-ath79-tiny-tplink_tl-waxxxxx-v1-squashfs-factory.bin
> erase 0x9f020000 +0x3c0000
> cp.b 0x80000000 0x9f020000 0x3c0000
> bootm 0x9f020000
- flash factory image from OEM WebUI
- sysupgrade from ar71xx image
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Looking at the current upstream driver implementation, it seems like the
TX/RX flow control is enabled only if the flow control pause option is
resolved from the device/link partner advertisements (or otherwise set).
On the other hand, our current in-tree driver force enables TX/RX
flow control by default, thus possibly leading to TX timeouts if the
other end sends pause frames (which are not properly handled?):
WARNING: CPU: 3 PID: 0 at net/sched/sch_generic.c:320 dev_watchdog+0x1ac/0x324
NETDEV WATCHDOG: eth0 (mtk_soc_eth): transmit queue 0 timed out
Disabling the flow control on PORT 5 MAC seems to fix this issues as the
pause frames are then filtered out. While at it, I'm removing the if
condition completely as suggested, since this code is run only on mt7621
SoC, so there is no need to check for the silicon revisions.
Ref: https://lists.openwrt.org/pipermail/openwrt-devel/2017-November/009882.html
Ref: https://forum.openwrt.org/t/mtk-soc-eth-watchdog-timeout-after-r11573/50000/12
Suggested-by: Felix Fietkau <nbd@nbd.name>
Reported-by: Rosen Penev <rosenp@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
With the wrong blocksize, the rootfs was not positioned on the boundary
of a block, thus breaking the mtdsplit driver.
Signed-off-by: David Bauer <mail@david-bauer.net>
This adds the label MAC address for the Ubiquiti Picostation M (XM).
This was overlooked when adding support in the previous patch.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This adds support for the Ubiquiti Picostation M (XM), which has the
same board/LEDs as the Bullet M XM, but different case and antennas.
Specifications:
- AR7241 SoC @ 400 MHz
- 32 MB RAM
- 8 MB SPI flash
- 1x 10/100 Mbps Ethernet, 24 Vdc PoE-in
- External antenna: 5 dBi (USA), 2 dBi (EU)
- POWER/LAN green LEDs
- 4x RSSI LEDs (red, orange, green, green)
- UART (115200 8N1) on PCB
Flashing via WebUI:
Upload the factory image via the stock firmware web UI.
Attention: airOS firmware versions >= 5.6 have a new bootloader with
an incompatible partition table!
Please downgrade to <= 5.5 _before_ flashing OpenWrt!
Refer to the device's Wiki page for further information.
Flashing via TFTP:
Same procedure as other NanoStation M boards.
- Use a pointy tool (e.g., pen cap, paper clip) and keep the reset
button on the device or on the PoE supply pressed
- Power on the device via PoE (keep reset button pressed)
- Keep pressing until LEDs flash alternatively LED1+LED3 =>
LED2+LED4 => LED1+LED3, etc.
- Release reset button
- The device starts a TFTP server at 192.168.1.20
- Set a static IP on the computer (e.g., 192.168.1.21/24)
- Upload via tftp the factory image:
$ tftp 192.168.1.20
tftp> bin
tftp> trace
tftp> put openwrt-ath79-generic-xxxxx-ubnt_picostation-m-squashfs-factory.bin
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This adds support for the Ubiquiti Nanostation Loco M (XM), which
has the same board/LEDs as the Bullet M XM, but different case and
antennas.
Specifications:
- AR7241 SoC @ 400 MHz
- 32 MB RAM
- 8 MB SPI flash
- 1x 10/100 Mbps Ethernet, 24 Vdc PoE-in
- NS Loco M2: built-in antenna: 8 dBi; AR9287
- NS Loco M5: built-in antenna: 13 dBi; 2T2R 5 GHz radio
- POWER/LAN green LEDs
- 4x RSSI LEDs (red, orange, green, green)
- UART (115200 8N1) on PCB
Flashing via WebUI:
Upload the factory image via the stock firmware web UI.
Note that only certain firmware versions accept unsigned
images. Refer to the device's Wiki page for further information.
Flashing via TFTP:
Same procedure as other NanoStation M boards.
- Use a pointy tool (e.g., pen cap, paper clip) and keep the reset
button on the device or on the PoE supply pressed
- Power on the device via PoE (keep reset button pressed)
- Keep pressing until LEDs flash alternatively LED1+LED3 =>
LED2+LED4 => LED1+LED3, etc.
- Release reset button
- The device starts a TFTP server at 192.168.1.20
- Set a static IP on the computer (e.g., 192.168.1.21/24)
- Upload via tftp the factory image:
$ tftp 192.168.1.20
tftp> bin
tftp> trace
tftp> put openwrt-ath79-generic-xxxxx-ubnt_nanostation-loco-m-squashfs-factory.bin
Tested on NanoStation Loco M2.
Signed-off-by: Sven Roederer <freifunk@it-solutions.geroedel.de>
Co-developed-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Several devices with tplink-safeloader contain default values (0x0)
for TPLINK_HWID and TPLINK_HWREV in their device definitions.
Move those to common tplink-safeloader definition so they do not
have to be repeated each time.
While at it, set default value for tplink-v1 and tplink-v2 as well.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This adds a pinmux to the shared DTSI for TP-Link TL-WR841N/ND v8,
TL-WR842N v2 and TL-MR3420 v2. It is supposed to be the equivalent
of:
/* config gpio4 as normal gpio function */
ath79_gpio_output_select(TL_MR3420V2_GPIO_USB_POWER,AR934X_GPIO_OUT_GPIO);
This allows to enable USB power on these devices.
While at it, move the jtag_disable_pins to &gpio node and remove the
redundant status=okay there.
Tested on TP-Link TL-WR842N v2.
Fixes: FS#2753
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Armin Fuerst <armin@fuerst.priv.at>
Mikrotik devices will be found in both generic and nand subtargets.
The file mikrotik-caldata.sh, currently used in generic, contains
a few lines of code that would need to be duplicated for nand
support. Instead of duplicating it, move it to target base-files,
as size impact is small and the maintenance gain should outweigh it.
This is changed separately to make life easier for the people
currently working on Mikrotik NAND support.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Hardware
--------
SoC: Atheros AR7161
RAM: Samsung K4H511638D-UCCC
2x 64M DDR1
SPI: Micron M25P128 (16M)
WiFi: Atheros AR9160 bgn
Atheros AR9160 an
ETH: Broadcom BCM5481
LED: Power (Green/Red)
ETH (Green / Blue / Yellow)
(PHY-controlled)
WiFi 5 (Green / Blue)
WiFi 2 (Green / Blue)
BTN: Reset
Serial: Cisco-Style RJ45 - 115200 8N1
Installation
------------
1. Download the OpenWrt initramfs-image. Place it into a TFTP server
root directory and rename it to 1401A8C0.img. Configure the TFTP
server to listen at 192.168.1.66/24.
2. Connect the TFTP server to the access point.
3. Connect to the serial console of the access point. Attach power and
interrupt the boot procedure when prompted (bootdelay is 1 second).
4. Configure the U-Boot environment for booting OpenWrt from Ram and
flash:
$ setenv boot_openwrt 'setenv bootargs; bootm 0xbf080000'
$ setenv ramboot_openwrt 'setenv serverip 192.168.1.66;
tftpboot; bootm'
$ saveenv
5. Load OpenWrt into memory:
$ run ramboot_openwrt
Wait for the image to boot.
6. Transfer the OpenWrt sysupgrade image to the device. Write the image
to flash using sysupgrade:
$ sysupgrade -n /path/to/openwrt-sysuograde.bin
Signed-off-by: David Bauer <mail@david-bauer.net>
The Siemens WS-AP3610 asserts reset to the ethernet PHY with the
reset-register. Backport the necessary patches to de-assert reset
when probing the PHY.
These patches can be dropped when using kernel 5.4.
Signed-off-by: David Bauer <mail@david-bauer.net>
This change makes the names of Broadcom targets consistent by using
the common notation based on SoC/CPU ID (which is used internally
anyway), bcmXXXX instead of brcmXXXX.
This is even used for target TITLE in make menuconfig already,
only the short target name used brcm so far.
Despite, since subtargets range from bcm2708 to bcm2711, it seems
appropriate to use bcm27xx instead of bcm2708 (again, as already done
for BOARDNAME).
This also renames the packages brcm2708-userland and brcm2708-gpu-fw.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Álvaro Fernández Rojas <noltari@gmail.com>
This change makes the names of Broadcom targets consistent by using
the common notation based on SoC/CPU ID (which is used internally
anyway), bcmXXXX instead of brcmXXXX.
This is even used for target TITLE in make menuconfig already,
only the short target name used brcm so far.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This change makes the names of Broadcom targets consistent by using
the common notation based on SoC/CPU ID (which is used internally
anyway), bcmXXXX instead of brcmXXXX.
This is even used for target TITLE in make menuconfig already,
only the short target name used brcm so far.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This backports SATA performance boost from 5.3 kernel:
Increasing the SATA/AHCI DMA TX/RX FIFOs (P0DMACR.TXTS and .RXTS, ie.
TX_TRANSACTION_SIZE and RX_TRANSACTION_SIZE) from default 0x0 each to
0x3 each, gives a write performance boost of 120 MiB/s to 132 MiB/s from
lame 36 MiB/s to 45 MiB/s previously. Read performance is above 200
MiB/s. [tested on SSD using dd bs=4K/8K/12K/16K/20K/24K/32K: peak-perf
at 12K]
dd bs Before MB/s After MB/s Increase
4k 14.4 16.5 15%
64k 34.5 74.4 116%
1M 40.5 93.2 130%
Ref: https://forum.openwrt.org/t/sunxi-sata-write-speed-patch/54555/5
Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
[commit subject & description tweaks]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
The TL-WR940N v6 is similar to v3/v4, it just has different
LEDs and MAC address assignment.
Specification:
- 750 MHz CPU
- 32 MB of RAM
- 4 MB of FLASH
- 2.4 GHz WiFi
- 4x 10/100 Mbps Ethernet
The use of LEDs is based on ar71xx, so blue LED is used for WAN
and orange LED for diag (boot/failsafe/etc.).
Flash instruction (WebUI):
Download *-factory.bin image and upload it via the firmwary upgrade
function of the stock firmware WebUI.
Flash instruction (TFTP):
1. Set PC to fixed ip address 192.168.0.66
2. Download *-factory.bin image and rename it to
wr940nv6_tp_recovery.bin
3. Start a tftp server with the image file in its root directory
4. Turn off the router
5. Press and hold Reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time
the firmware should be transferred from the tftp server
8. Wait ~30 second to complete recovery.
Thanks to Manuel Kock for reviewing and testing this patch.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Manuel Kock <github.web@manu.li>
This adds the ar71xx board name to the SUPPORTED_DEVICES on ath79,
so forceless sysupgrade on this device becomes possible.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Since kernel 5.2 within netlink messages the NLA_F_NESTED nested flag is
validated. But swconfig/swlib doesn't set the flag for
SWITCH_ATTR_OP_VALUE_PORTS related netlink messages and assigning ports
to vlans via
swconfig dev switch0 vlan 1 set ports '0 1 2 3 4 6t'
Errors put with "Failed to set attribute: Invalid input data or
parameter".
Relax the validation rules and use the deprecated functions, to use the
same level of validation as it was till kernel 5.1. Depending on who has
swconfig related netlink messages implemented, there might be more
broken tools out there and we should keep backward compatibility if
possible.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Tested-by: Rafał Miłecki <rafal@milecki.pl>
Make run_parsers_by_type() more similar to the parse_mtd_partitions():
1. Use struct mtd_partitions
2. Use add_mtd_partitions()
This change simplifies run_parsers_by_type() by:
1. Dropping loop
2. Dropping code getting partition properties (name, offset, size)
Moreover this change allows passing more partitions details (e.g.
mask_flags).
One noticeable change introduced by this patch is adding parsed
partitions as children. This results in printing their *relative*
offsets which unifies this code with parse_mtd_partitions() behaviour.
Before:
[ 1.785448] 0x00000018f800-0x000000fb0000 : "rootfs"
[ 1.791642] mtd: device 4 (rootfs) set to be root filesystem
[ 1.797537] 1 squashfs-split partitions found on MTD device rootfs
[ 1.804009] 0x0000004e0000-0x000000fb0000 : "rootfs_data"
After:
[ 1.785376] 0x00000018f800-0x000000fb0000 : "rootfs"
[ 1.791601] mtd: device 4 (rootfs) set to be root filesystem
[ 1.797491] 1 squashfs-split partitions found on MTD device rootfs
[ 1.803936] Creating 1 MTD partitions on "rootfs":
[ 1.808910] 0x000000350800-0x000000e20800 : "rootfs_data"
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Stock firmware has a vendor-defined tail at the end of uImage for image
validation. This patch enables OpenWrt installation from stock firmware
without having to access the UART console.
Installation via web interface:
1. Flash **initramfs** image through the stock web interface.
2. Boot into OpenWrt and perform sysupgrade with sysupgrade image.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
This ports support for the TL-WA830RE v1 range extender from ar71xx to
ath79.
Specifications:
- SOC: Atheros AR7240
- CPU: 400MHz
- Flash: 4 MiB (Spansion S25FL032P)
- RAM: 32 MiB (Zentel A3S56D40FTP-G5)
- WLAN: Atheros AR9280 bgn 2x2
- Ethernet: 1 port (100M)
Flash instructions:
- install from u-boot with tftp (requires serial access)
> setenv ipaddr a.b.c.d
> setenv serverip e.f.g.h
> tftpboot 0x80000000 \
openwrt-ath79-tiny-tplink_tl-wa830re-v1-squashfs-factory.bin
> erase 0x9f020000 +0x3c0000
> cp.b 0x80000000 0x9f020000 0x3c0000
> bootm 0x9f020000
- flash factory image from OEM WebUI
- sysupgrade from ar71xx image
The device seems to be a clone of the following devices not yet
added to ath79:
- tl-wa701nd-v1
- tl-wa730re-v1
- tl-wa801nd-v1
- tl-wa901nd-v1
Signed-off-by: Christian Buschau <christian.buschau@mailbox.org>
[make use of ar7240_tplink.dtsi, add note about clones]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The current set of TP-Link devices with ar7240 SoC all share
the same DTSI file. As the latter is very similar to the
definition required for the to-be-supported TP-Link TL-WA devices
with ar7240, this patch splits the definitions into a shared part
for all TP-Link devices (ar7240_tplink.dtsi) and a file containing
the specific setup for the present TL-WR devices
(ar7240_tplink_tl-wr.dtsi), equivalent to the former
ar7240_tplink_tl-wr74xn-v1.dtsi.
While at it, remove unused firmware partition label and rename
pinmux_switch_led_pins.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
If bootloader doesn't terminate its last spi operation properly
before starting kernel, our first transfer in kernel becomes a
continuous transfer to that request instead of a new one.
Fix this flaw by restoring IOC register, which restored all pin
state to default.
Fixes: ebf0d8dade ("ath79: add new ar934x spi driver")
Reported-by: Russell Senior <russell@personaltelco.net>
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
When changing compatibles in e4ba8c8294 ("brcm63xx: use more systematic
names for image and DTS files"), I forgot to update them in kernel
patches as well. So, do it now.
Fixes: e4ba8c8294 ("brcm63xx: use more systematic names for image and DTS files")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This uses the specific SOC names for several devices where the
Chip ID was used incorrectly before.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Since the model string in DTS is not required to derive board name
anymore, we can now align it with the model name in Makefile and
the compatible.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This patch removes the translation of device model name into a
board name in lib/brcm63xx.sh. The latter has been actually totally
useless as we have the compatible which can be used instead of
the board name (and actually is at other targets like ath79 or ramips).
The change requires updating the base-files with the new
identifiers based on compatible.
With all "board names" replaced by the compatible, we do not need
the old scripts to detect board name anymore and can also remove
the obsolete treatment of "legacy" devices without DTS, as there
are none of those left. So, this patch removes the target-specific
board detection and uses the standard procedure in
package/base-files/files/lib/preinit/02_sysinfo
This also fixes several cases where the board name was not set or
evaluated correctly:
- asmax,ar1004g in 02_network
- telsey,magic in 09_fix_crc/02_network
- brcm,bcm96338gw in 02_network
- brcm,bcm96338w in 02_network
- brcm,bcm96348gw in 02_network
- dynalink,rta1025w in 02_network
- huawei,echolife-hg520v in 02_network
- several cases in diag.sh
The following orphaned identifiers are removed from board.d files:
- dmv-s0
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
In brcm63xx image Makefile DEVICE_PACKAGE definitions are split
into multiple lines with no apparent need.
Merge them into one line to increase readability and maintainability.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This changes brcm63xx target to achieve consistency between image
names, device nodes names, compatible, DTS name and device name
as much as possible. As with other targets, having consistent
names is supposed to make life easier for developers and reduces
the number of "variables" in the system. In particular, applying
the DTS scheme will make it easier to find the correct file and
architecture.
DTS files are named based on the increasingly common
soc-vendor-model scheme, using hyphens for separation as this seems
to be the kernel way. Since the compatible is not used at the
moment, I took the chance to also align them with this patch.
For the SOC, the already existing CFE_CHIP_ID can be exploiting
for all but two devices.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The correct model name of WF-2881 is WF2881 without hyphen. The former used
boardnames are not added to SUPPORTED_DEVICES, to make it explicit that the
sysupgrade-tar image, which is newly added in the previous commit, should
not be used to upgrade from older version.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[adjust commit title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
WF-2881 sysupgrade image uses UBI rootfs, but still relies on
default_do_upgrade. Because of this, config backup is not restored after
sysupgrade. It can be fixed by switching to nand_do_upgrade and
sysupgrade-tar image. default_do_upgrade does not handle sysupgrade-tar
properly, so one should use factory image to upgrade from older version.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Inspired by commit c48b571ad7, add an LED trigger for the WAN LED on top of
the TP-Link TL-WR902AC v1. Currently, only the LED on the port itself shows the
link state, while the LED on top of the device stays dark.
The WAN port of the device is a hybrid LAN/WAN one, hence why the LED at the
port was labeled LAN.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
AR934x chips also got the 'old' qca,ar9330-uart in addition to the
'new' ns16550a compatible one. Add support for UART1 clock selector as
well as device-tree bindings in ar934x.dtsi to make use of that uart.
Reported-by: Piotr Dymacz <pepe2k@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
On AR934x this UART is usually not initialized by the bootloader
as it is only used as a secondary serial port while the primary
UART is a newly introduced NS16550-compatible.
In order to make use of the ar933x-uart on AR934x without RTS/CTS
hardware flow control, one needs to set the
UART_CS_{RX,TX}_READY_ORIDE bits as other than on AR933x where this
UART is used as primary/console, the bootloader on AR934x typically
doesn't set those bits.
Setting them explicitely on AR933x does not do any harm, so just set
them unconditionally.
Tested-by: Chuanhong Guo <gch981213@gmail.com
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Luxul ABR-4500 and XBR-4500 devices are wired routers with 5 Ethernet
ports and 1 USB 3.0 port. Flashing requires using Luxul firmware 6.4.0
or newer and uploading firmware using "Firmware Update" web UI page.
Signed-off-by: Dan Haab <dan.haab@legrand.com>
This new function make batch processing of network packets possible,
which slightly improves performance.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Tested-by: Rosen Penev <rosenp@gmail.com>
XTX XT25F128A shares it's chip ID with XM25QH128A which got identical
features. Hence there it makes no sense to add it to the driver.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
ar933x appears to have the same spi controller as ar934x but it's
not mentioned in datasheet at all. Use new spi driver instead to
gain more flash operating performance.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
A new shift mode was introduced since ar934x which has a way better
performance than current bitbang driver and can handle higher spi
clock properly. This commit adds a new driver to make use of this
new feature.
This new driver has chipselect properly configured and we don't need
cs-gpios hack in dts anymore. Remove them.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
This commit adds the ability to set custom uImage magic to
Build/wr1201-factory-header and renames it to
"Build/custom-initramfs-uimage".
Custom uImage header in initramfs image is required on following
devices:
- I-O DATA WN-AX1167GR2
- I-O DATA WN-AX2033GR
- I-O DATA WN-AX2033GR2
- I-O DATA WN-DX1167R
While at it, fix typo in comment.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Reviewed-by: Sungbo Eo <mans0n@gorani.run>
[shorten commit title, minor commit message adjustments]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
dts file does not need to be executable. 644 is enough.
Fixes: f098c612b6 ("ramips: create shared DTSI for Netgear EX2700 and WN3000RP v3")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
kernel config and patch files do not need to be executable. 644 is enough.
Fixes: 01c8f2e97c ("mediatek: bump to v4.19")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Remove read-only flag from U-boot environment partition for Netgear
WNDR3700 v1 and v2 so u-boot-envtools can modify data there.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
Since whole target has been bumped to kernel 4.19 in 01c8f2e97c
("mediatek: bump to v4.19") we do not need the overwrite in mt7629
subtarget anymore.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This commit adds support for the COMFAST CF-E560AC, an ap143 based
in-wall access point.
Specifications:
- SoC: Qualcomm Atheros QCA9531
- RAM: 128 MB DDR2 (Winbond W971GG6SB-25)
- Storage: 16 MB NOR (Winbond 25Q128JVSO)
- WAN: 1x 10/100 PoE ethernet (48v)
- LAN: 4x 10/100 ethernet
- WLAN1: QCA9531 - 802.11b/g/n - 2x SKY85303-21 FEM
- WLAN2: QCA9886 - 802.11ac/n/a - 2x SKY85735-11 FEM
- USB: one external USB2.0 port
- UART: 3.3v, 2.54mm headers already populated on board
- LED: 7x external
- Button: 1x external
- Boot: U-Boot 1.1.4 (pepe2k/u-boot_mod)
MAC addressing:
- stock
LAN *:40 (label)
WAN *:41
5G *:42
2.4G *:4a
- flash (art partition)
0x0 *:40 (label)
0x6 *:42
0x1002 *:41
0x5006 *:43
This device contains valid MAC addresses in art 0x0, 0x6, 0x1002 and
0x5006, however the vendor firmware only reads from art:0x0 for the LAN
interface and then increments in 02_network. They also jump 8 addresses
for the second wifi interface (2.4 GHz). This behavior has been duplicated
in the DTS and ath10k hotplug to align addresses with the vendor firmware
v2.6.0.
Recovery instructions:
This device contains built-in u-boot tftp recovery.
1. Configure PC with static IP 192.168.1.10/24 and tftp server.
2. Place desired image at /firmware_auto.bin at tftp root.
3. Connect device to PC, and power on.
4. Device will fetch flash from tftp, flash and reboot into new image.
Signed-off-by: August Huber <auh@google.com>
[move jtag_disable_pins, remove unnecessary statuses in DTS, remove
duplicate entry in 11-ath10k-caldata, remove hub_port0 label in DTS]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adapt Netgear WNDR3700v2 device identification string to ath79 naming
scheme by changing from 'wndr3700v2' to 'wndr3700-v2' (affects config,
makefile, init scripts and device tree definition).
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
This adds a shared definition Device/tplink-v2 to common-tp-link.mk.
Though currently only one device in ath79 uses it, putting it in
the common file seems more organized. The definitions are based
on the implementation in ramips target, where a lot of devices
is using tplink-v2-* commands already.
The '-V "ver. 2.0"' suffix for Archer D50 v1 can be removed because
it's default in Build/tplink-v2-image anyway.
While at it, add TPLINK_HWREVADD and TPLINK_HVERSION to DEVICE_VARS,
which seems to have been overlooked when adding Archer D50 v1.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This renames Device/tplink-loader-okli to Device/tplink-safeloader-okli
since the latter more accurately describes the combination of
tplink-safeloader and loader-okli use there. The old version might
be confused with other uses of the okli loader.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
As we have tplink-v2-header and tplink-v2-image recipes as well,
this patch renames the Device/tplink definition to Device/tplink-v1,
as it's using the tplink-v1-* commands. This should provide easier
distinction in the future.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Align subtargets makefiles names to actual subtargets.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Acked-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This sorts the devices in image Makefiles alphabetically.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
[fixed sorting in one case, add commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
TP-Link RE200 v2 is a wireless range extender with Ethernet and 2.4G and 5G
WiFi with internal antennas. It's based on MediaTek MT7628AN+MT7610EN.
Specifications
--------------
- MediaTek MT7628AN (580 Mhz)
- 64 MB of RAM
- 8 MB of FLASH
- 2T2R 2.4 GHz and 1T1R 5 GHz
- 1x 10/100 Mbps Ethernet
- UART header on PCB (57600 8n1)
- 8x LED (GPIO-controlled), 2x button
There are 2.4G and 5G LEDs in red and green which are controlled
separately.
MAC addresses
-------------
The MAC address assignment matches stock firmware, i.e.:
LAN : *:0D
2.4G: *:0E
5G : *:0F
Installation
------------
Web Interface
-------------
It is possible to upgrade to OpenWrt via the web interface. Simply flash
the -factory.bin from OEM. In contrast to a stock firmware, this will not
overwrite U-Boot.
Serial console
--------------
Opening the case is quite hard, since it is welded together. Rename the
OpenWrt factory image to "test.bin", then plug in the device and quickly
press "2" to enter flash mode (no line feed). Follow the prompts until
OpenWrt is installed.
Unfortunately, this devices does not offer a recovery mode or a tftp
installation method. If the web interface upgrade fails, you have to open
your device and attach serial console.
Additonal notes
---------------
It is possible to flash back to stock by using tplink-safeloader to create
a sysupgrade image based on a stock update. After the first boot, it is
necessary upgrade to another stock image, otherwise subsequent boots
fail with LZMA ERROR 1 and you have to attach serial to recover the device.
Signed-off-by: Andreas Böhler <dev@aboehler.at>
[remove DEVICE_VARS change]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This moves the various variants of common device definitions for
TP-Link devices to a common Makefile common-tp-link.mk. This
provides the opportunity to reorganize and move parameters between
individual device definitions and the common ones.
While at it, also use the common definitions for previously
independent definitions where appropriate.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
I'm having another attempt at trying to getting the 'store dscp into
conntrack connmark' functionality into upstream kernel, since the
restore function (act_ctinfo) has been accepted.
The syntax has changed from 'savedscp' to 'set-dscpmark' since that
conforms more closely with existing functionality.
4.14 backport is more of a hack since the structure versioning
mechanism isn't in place.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
This commit adds support for the NanoStation Loco M2/M5 XW devices
on the ath79 target (support was long ago available on ar71xx).
Specifications:
- AR9342 SoC @ 535 MHz
- 64 MB RAM
- 8 MB SPI flash
- 1x 10/100 Mbps Ethernet, 24 Vdc PoE-in
- AR8032 switch
- 2T2R 5 GHz radio, 22 dBm
- 13 dBi built-in antenna
- POWER/LAN green LEDs
- 4x RSSI LEDs (red, orange, green, green)
- UART (115200 8N1) on PCB
Flashing via TFTP:
- Use a pointy tool (e.g., pen cap, paper clip) and keep the reset
button on the device or on the PoE supply pressed
- Power on the device via PoE (keep reset button pressed)
- Keep pressing until LEDs flash alternatively LED1+LED3 =>
LED2+LED4 => LED1+LED3, etc.
- Release reset button
- The device starts a TFTP server at 192.168.1.20
- Set a static IP on the computer (e.g., 192.168.1.21/24)
- Upload via tftp the factory image:
$ tftp 192.168.1.20
tftp> bin
tftp> trace
tftp> put openwrt-ath79-generic-xxxxx-ubnt_nanostation-loco-m-xw-squashfs-factory.bin
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
There are several cases where phy-mode and status properties are
set again in DTS(I) files although those were set to the same values
in parent DTSI files already. Remove those cases (and thus also stop
their proliferation by copy/paste).
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
A minority of ethernet-phy definitions seems to use numbers in label,
name and reg property relatively random. This patch aligns their
use to have the same numeric value for all of them.
While at it, improve order of properties/add newlines for the ethX
nodes where necessary.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The image creation for the mt7623a-rfb-emmc has been removed during
a patch refresh without specific comment. The corresponding base-files
entries and DTS patches for 4.14 are still there.
Since mt7623 is pretty dead and nobody has missed this device, let's
just remove the rest.
Fixes: 050da2107a ("mediatek: backport upstream mediatek patches")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: John Crispin <john@phrozen.org>
This converts the TP-Link TL-MR3020v3 board to use the WLAN throughput
LED trigger in order to react to all VAPs.
It also moves the WLAN trigger config of the TP-Link TL-WA801NDv5 to the
DTS and merges the now identical LAN LED configs.
Verified these changes on a TL-MR3020v3.
Signed-off-by: Jan Alexander <jan@nalx.net>
[changed commit title and extended commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This reverts commit 4716c843d6.
Netgear seems to use different partition layouts on the R6260, which
would require us to dynamically detect the position of (at least) the
factory partition.
Revert this fix to avoid breaking existing installations until a better
solution has been worked out.
Signed-off-by: David Bauer <mail@david-bauer.net>
This fixes support for Teltonika RUT9xx which in recent versions of
the device uses xt25f128b flash.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
DEVICE_PACKAGES is specified twice for the same device. Remove the
first (=older) assignment.
Fixes: 40692f0fb5 ("ramips: mt7620: select only the matching mt76 driver")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This ports the GL.iNet 6408/6416 from ar71xx.
The GL-Connect GL.iNet v1 routers are basically a TP-Link TL-WR710N with
more DRAM/Flash and console/GPIO header in the same small form-factor.
Specifications:
- SoC: Atheros AR9331
- CPU: 400 MHz
- Flash: 8/16 MiB
- RAM: 64 MiB
- WiFi: 2.4 GHz b/g/n (SoC)
- Ethernet: 2x 100M ports (LAN/WAN)
- USB: 1x 2.0
The difference between 6408 and 6416 is just the flash size. It looks like
only the 16 MiB version has been advertised, while the 6408 is a modified
version. There are also 1-port versions sold by third parties.
Installation:
Install the sysupgrade image via stock firmware GUI or upload it via uboot
(web-based). The device will be available at 192.168.1.1.
Attention: In ar71xx, the same board name is used for both flash versions.
So, please make sure you flash the correct ath79 image when upgrading.
This has been device-tested on a GL.iNet 6416.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The EEPROM offset for the NETGEAR R6260 is incorrect, thus no valid
calibration data is used.
Fix this only for the NETGEAR R6260, as it's currently unknown whether
or not other boards are affected.
Signed-off-by: David Bauer <mail@david-bauer.net>
The GL.iNet microuter-N300 (internally referred as MT300N-v4) is a
pocket-size travel router. It is essentially identical to the VIXMINI
(internally referred as MT300N-v3) but with double the RAM and
SPI-flash.
Additionally, set the label-mac for both the VIXMINI as well as the
microuter-N300.
Hardware
--------
SoC: MediaTek MT7628NN
RAM: 128M DDR2
FLASH: 16M
LED: Power - WLAN
BTN: Reset
UART: 115200 8N1
TX and RX are labled on the board as pads next to the SoC
Installation via web-interface
------------------------------
1. Visit the web-interface at 192.168.8.1
Note: The ethernet port is by default WAN. So you need to connect to
the router via WiFi
2. Navigate to the Update tab on the left side.
3. Select "Local Update"
4. Upload the OpenWrt sysupgrade image.
Note: Make sure you select not to preserve the configuration.
Installation via U-Boot
-----------------------
1. Hold down the reset button while powering on the device.
Wait for the LED to flash 5 times.
2. Assign yourself a static IPv4 in 192.168.1.0/24
3. Upload the OpenWrt sysupgrade image at 192.168.1.1.
Signed-off-by: David Bauer <mail@david-bauer.net>
This updates the device definition name for octeon target to provide
more useful names for the images and be consistent with the increasing
number of targets following that scheme.
Since the target is not using device tree yet, this does not touch
board_name and thus sets BOARD_NAME in image Makefile to ensure
sysupgrade is still working.
While at it, move Build block before Device blocks and remove trailing
whitespace for CMDLINE.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This harmonizes the device node names (and thus the image names, too)
between subtargets of the mediatek target. So far, each subtarget
has somewhat used its own naming scheme. Now, we use the vendor_device
syntax there, too.
Since DTS names have different patterns and the target only contains
a few devices, this does not replace DEVICE_DTS by a calculated
default value (like for other targets).
SUPPORTED_DEVICES is adjusted based on the node rename where necessary,
though it looks like for several older devices it was not set up
correctly so far.
While at it, this also changes the DTS name for u7623-02-emmc-512m
to all-lower-case.
Cc: John Crispin <john@phrozen.org>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
"[[" is a bash extension for test. As the ash-implementation is not
fully compatible we drop its usage.
Signed-off-by: Sven Roederer <devel-sven@geroedel.de>
[split patch, remove shebang, adjust commit title/message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This patch fixes the occurences of the following warning
message from the dtc:
Warning (reg_format): /soc/spi@78b5000/flash0@0/partitions/partition@0:reg:
property has invalid length (8 bytes) (#address-cells == 2, #size-cells == 1)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
SOC: IPQ4018 / QCA Dakota
CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7
DRAM: 256 MiB
NOR: 32 MiB
ETH: Qualcomm Atheros QCA8072 (1 port)
WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2
WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2
INPUT: RESET Button
LEDS: White, Blue, Red, Orange
Flash instruction:
From EnGenius firmware to OpenWrt firmware:
In Firmware Upgrade page, upgrade your openwrt-ipq40xx-generic-engenius_emd1-squashfs-factory.bin directly.
From OpenWrt firmware to EnGenius firmware:
1. Setup a TFTP server on your computer and configure static IP to 192.168.99.8
Put the EnGenius firmware in the TFTP server directory on your computer.
2. Power up EMD1. Press 4 and then press any key to enter u-boot.
3. Download EnGenius firmware
(IPQ40xx) # tftpboot 0x84000000 openwrt-ipq40xx-emd1-nor-fw-s.img
4. Flash the firmware
(IPQ40xx) # imgaddr=0x84000000 && source 0x84000000:script
5. Reboot
(IPQ40xx) # reset
Signed-off-by: Yen-Ting-Shen <frank.shen@senao.com>
[removed BOARD_NAME]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Specifications
==============
- SOC: IPQ4018
- RAM: DDR3 256MB
- Flash: SPI NOR 16MB
- WiFi:
- 2.4GHz: IPQ4018, 2x2, front end SKY85303-11
- 5GHz: IPQ4018, 2x2, front end SKY85717-21
- Ethernet: 1x 10/100/1000Mbps, POE 802.3af
- PHY: QCA8072
- UART: GND, blocked, 3.3V, RX, TX / 115200 8N1
- LED: 1x red / green
- Button: 1x reset / factory default
- U-Boot bootloader with tftp and "emergency web server" accessible
using serial port.
Installation
============
Flash factory image from D-Link web UI. Constraints in the D-Link web UI
makes the factory image unnecessarily large. Flash again using
sysupgrade from inside OpenWrt to reclaim some flash space.
Return to stock D-Link firmware
===============================
Partition layout is preserved, and it is possible to return to the stock
firmware simply by downloading it from D-Link and writing it to the
firmware partition.
# mtd -r write dap2610-firmware.bin firmware
Quirks
======
To be flashable from the D-Link http server, the firmware must be larger
then 6MB, and the size in the firmware header must match the actual file
size. Also, the boot loader verifies the checksum of the firmware before
each boot, thus the jffs2 must be after the checksum covered part. This
is solved in the factory image by having the rootfs at the very end of
the image (without pad-rootfs).
The sysupgrade image which does not have to be flashable from the D-Link
web UI may be smaller, and the checksum in the firmware header only
covers the kernel part of the image.
Signed-off-by: Fredrik Olofsson <fredrik.olofsson@anyfinetworks.com>
[added WRGG Variables to DEVICE_VARS, squashed spi pinconf/mux,
added emd1's gmac0 config,fix dtc warnings]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This adds the missing assignment of DEFAULT_SOC to the SOC variable
by default.
Fixes: 09ee51c614 ("lantiq: define SOC only once for uniform targets")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
In lantiq there are several subtarget where all devices have the
same value set to the SOC variable for each device individually.
This patch introduces a non-device-dependent variable DEFAULT_SOC,
which is used if no specific SOC is set for a device, and thus reduces
the number of redundant definitions drastically.
This is applied to all subtargets except xway, as only the latter has
two different SOCs.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The DTS_DIR variable is not a device variable, thus it should not
be set inside Device/Default but globally.
Fixes: c640370939 ("lantiq: use soc_vendor_device scheme on DTS file")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The number 3 was accidentally removed from the name during split
of DEVICE_TITLE.
Fixes: fd66687058 ("lantiq: split up DEVICE_TITLE")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
In ramips, all devices in mt7621, mt76x8 and rt288x subtarget have
the same value set to the SOC variable for each device individually.
This patch introduces a non-device-dependent variable DEFAULT_SOC,
which is used if no specific SOC is set for a device, and thus reduces
the number of redundant definitions drastically.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Based on a script for comparison, this fixes (hopefully) all errors
in SUPPORTED_DEVICES for ar71xx->ath79 upgrade.
Devices where old string is removed as the device does not exist
in ar71xx:
- dlink_dir-859-a1
- tplink_archer-a7-v5
- tplink_cpe510-v3
Devices where string is changed because it did not match the board
name in ar71xx:
- tplink_tl-mr3220-v1
- tplink_tl-mr3420-v1
- tplink_tl-wr2543-v1
- tplink_tl-wr741nd-v4
- tplink_tl-wr841-v7
- ubnt_unifiac-mesh
- ubnt_unifiac-mesh-pro
- ubnt_unifiac-pro
For this device, the correct string could not be found, but we could
not determine the correct one. Thus, the string is removed for now:
- tplink_tl-wr740n-v4
The script for checking this is quite simple (note that newer
entries, i.e. ath79->ath79 upgrade, are displayed as missing):
newpath=target/linux/ath79/image/
oldpath=target/linux/ar71xx/base-files/lib/ar71xx.sh
for s in $(grep -roh "SUPPORTED_DEVICES.*" $newpath | sed 's/SUPPORTED_DEVICES *.= *//'); do
found="Missing"
grep -q -r "\"$s\"" $oldpath && found="Found"
echo "$s: $found."
done
The errors might be filtered by appending 'grep "Missing"' to the script.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
In certain cases, the uncompressed initramfs image will overwrite
the lzma-loader, which is currently only 10 MB away from kernel image
start. To prevent this, change LZMA_TEXT_START to 24 MB, so loader
and compressed image have 8 MB at the end of RAM and uncompressed
image has 24 MB available.
This is only enabled for ath79 at the moment, as there we can be sure
that all devices have 32+ MB RAM and TARGET_INITRAMFS_COMPRESSION_LZMA
is not enabled there.
Despite, since lzma-loader is currently build specifically for ath79
anyway, there is no need to re-specify LOADADDR and LZMA_TEXT_START
in image/Makefile, so the values are set directly in
image/lzma-loader/Makefile and the overwrite in image/Makefile is
removed.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
This commit adds support for the MikroTik RouterBOARD wAP G-5HacT2HnD
(wAP AC), a small weatherproof dual band, dual-radio 802.11ac
wireless AP with integrated omnidirectional anntennae and one
10/100/1000 Mbps Ethernet port.
See https://mikrotik.com/product/RBwAPG-5HacT2HnD for more info.
Specifications:
- SoC: Qualcomm Atheros QCA9556
- RAM: 64 MB
- Storage: 16 MB NOR
- Wireless:
· Atheros AR9550 (SoC) 802.11b/g/n 2x2:2, 2 dBi antennae
· Qualcomm QCA9880 802.11a/n/ac 3x3:3, 2 dBi antennae
- Ethernet: Atheros AG71xx (SoC, AR8033), 1x 1000/100/10 port,
passive PoE in
Working:
- Board/system detection
- Sysupgrade
- Serial console
- Ethernet
- 2.4 GHz radio
- 5 GHz radio and LED
- Reset button
Not working/Unsupported:
- 2.4 GHz LED
- AP/CAP LED
- ZT2046Q SPI temperature and voltage sensor
This adds the basic features for supporting MikroTik devices:
- a common recipe for mikrotik images in common-mikrotik.mk
- support for minor (MikroTik NOR) split firmware (only for
generic subtarget so far)
Acknowledgments: Robert Marko <robimarko@gmail.com>
Andrew Cameron <apcameron@softhome.net>
Koen Vandeputte <koen.vandeputte@ncentric.com>
Chuanhong Guo <gch981213@gmail.com>
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Co-developed-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
In order to make the QCA955x SGMII workaround work, the unsuccessful
SGMII autonegotiation on the AR8033 should not block the PHY
state-machine.
Otherwise, the ag71xx driver never becomes aware of the copper-side
link-establishment and the workaround is never executed.
Signed-off-by: David Bauer <mail@david-bauer.net>
[remove one trailing whitespace per file]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This commit adds a workaround for the loss of the SGMII link observed on
the QCA955x generation of SoCs. The workaround originates part from the
U-Boot source code, part from the implementation from AVM found in the
GPL tarball for the AVM FRITZ!WLAN Repeater 450E.
The bug results in a stuck SGMII link between the PHY device and the SoC
side. This has only been observed with the Atheros AR8033 PHY and most
likely all devices using such combination are affected.
It is worked around by reading a hidden SGMII status register and
issuing a SGMII PHY reset until the link becomes useable again.
Signed-off-by: David Bauer <mail@david-bauer.net>
Due to the history of the target, all devices added before a certain
point have the same device string in BOARD_NAME, DEVICE_DTS and added
to SUPPORTED_DEVICES.
Thus, we can set this one automatically for all devices where
BOARD_NAME is specified, removing the explicit DEVICE_DTS and
SUPPORTED_DEVICES addition there.
For new devices, nothing has changed, and just DEVICE_DTS has to
be set manually.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This tidies up the image Makefiles for the sunxi target by:
- Move the if-condition for the subtarget to the parent Makefile
- Remove lots of unnecessary empty lines
- Sort device definitions alphabetically
- Harmonize line wrapping for DEVICE_PACKAGES
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Change u-boot-env partitions to be mounted as read-write for gl-ar150,
gl-domino and gl-mifi so uboot-envtools support is possible.
Signed-off-by: Kimmo Vuorinen <kimmo.vuorinen@gmail.com>
[commit title/message facelift]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
TP-Link TL-WA850RE v2 is a wall-plug N300 Wi-Fi range extender,
based on Qualcomm/Atheros QCA9533 v2.
Short specification:
- 550/391/195 MHz (CPU/DDR/AHB)
- 1x 10/100 Mbps Ethernet
- 32 MB of RAM (DDR1)
- 4 MB of FLASH
- 2T2R 2.4 GHz
- 2x internal antennas (embedded on PCB)
- 9x LED (all can be turned off with GPIO15), 2x button
- UART (J3) header on PCB
Flash instruction: use "factory" image directly in vendor GUI.
Warning: this device does not include any kind of recovery mechanism
in the bootloader and disassembling process is not trivial.
You can access vendor firmware over serial line using:
- login: root
- password: sohoadmin
Stock firmware uses label MAC address for WiFi and same with local
bit set for ethernet. Since this is difficult to reproduce with
the toolset of OpenWrt, we just keep both ethernet and WiFi to
the same address here.
This is the first tiny device with tplink-safeloader in ath79.
Firmware partition is only 3648k and thus even smaller than for
the tplink-4m(lzma) devices.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This moves the TP-Link TL-WA850RE v2 to dynamic partitioning and
will allow to use this for ath79 as well.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
- Remove the "RGMII TX delay fixup" hack and the associated
DT-property. It was never used in a DT-based platform and
solved a problem which can be mitigated by using correct
delays on the MAC side.
- Remove the patch to enable platform-data support for the
at803x driver. It was only used by ar71xx which does not
(and never will) support kernel 4.19 or later.
- Remove the SmartEEE DT-configuration patch. As explained
previously, this patch never disabled the Atheros SmartEEE
implementation, but rather "standard" EEE. This can be done
on device-tree compatible platforms by adding the
"eee-broken-1000t" or "eee-broken-100tx" properties to the PHY
node. As all usages of the old properties are migrated, this
patch can be removed.
Signed-off-by: David Bauer <mail@david-bauer.net>
Acked-by: Christian Lamparter <chunkeey@gmail.com>
The hack-patch which introduced the "at803x-disable-smarteee" for
disabling SmartEEE did in fact not disable SmartEEE but rather disabled
802.3az "standard" EEE.
This can be done by using the upstream properties "eee-broken-100tx" and
"eee-broken-1000t". EEE is then disabled by the PHY subsystem.
Tested on devolo WiFi pro 1200e.
Signed-off-by: David Bauer <mail@david-bauer.net>
This ports support for the TL-WA850RE v1 range extender from ar71xx
to ath79.
Specifications:
Board: AP123 / AR9341 rev. 3
Flash/RAM: 4/32 MiB
CPU: 535 MHz
WiFi: 2.4 GHz b/g/n
Ethernet: 1 port (100M)
Flashing instructions:
Upload the factory image via the vendor firmware upgrade option.
Recovery:
Note that this device does not provide TFTP via ethernet like many
other TP-Link devices do. You will have to open the case if you
require recovery beyond failsafe.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Add patches retrying to probe the PHY to restore support for PHYs taking
longer to initialize without breaking modules without PHYs.
Patches taken from http://git.armlinux.org.uk/cgit/linux-arm.git/log/?h=phy
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Update the uDPU kernel support, fixing a number of issues:
* make ethernet work again by adding comphy definitions
* slow the I2C bus to give it more chance of actually working
* the SFP cages are designed to support up to 3W modules, which
would be prevented from initialising without this patch.
Signed-off-by: Russell King <linux@armlinux.org.uk>
[jonas.gorski: rename to mvebu, refresh patches]
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Add support for Methode DM7052 NBASE-T module to OpenWRT. These
patches are taken from my "phy" branch, and will be sent for the
next kernel merge window.
Signed-off-by: Russell King <linux@armlinux.org.uk>
[jonas.gorski: move patches to pending, refresh patches]
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Backport the phy/phylink/sfp patches currently queued in netdev or in
mainline necessary to support GPON popular modules, specifically to
support Huawei and Nokia GPON modules.
Signed-off-by: Russell King <linux@armlinux.org.uk>
[jonas.gorski: include kernel version in file names, refresh patches]
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Move two phylink patches from mvebu to generic, so that everyone can
benefit from them.
Signed-off-by: Russell King <linux@armlinux.org.uk>
[jonas.gorski: add kernel version to file names]
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Remove the old phylink/SFP patches from the OpenWRT build; these will
be updated with a new set in subsequent.
450-reprobe_sfp_phy is also removed for several reasons:
1) it is not in mainline.
2) it breaks copper modules that do not have a PHY.
3) it makes backporting the current patch set harder.
Discussion is ongoing with the patch author for a mainline Linux kernel
patch for this.
Signed-off-by: Russell King <linux@armlinux.org.uk>
TPLINK_BOARD_NAME has been renamed to TPLINK_BOARD_ID a long time
ago (7d6c63d87542: "build: rename TPLINK_BOARD_NAME to
TPLINK_BOARD_ID" for ar71xx), and before introducing ath79 target
at all.
TPLINK_BOARD_NAME seems to have been introduced into ath79 target
only by mistake. It has never been used. Remove it.
Fixes: 53c474abbd ("ath79: add new OF only target for QCA MIPS silicon")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This reverts commit de80424f70 which needs
more work and testing as it broke at least jffs2 overlays at least on
ath79 platform, marking them as read-only, thus unusable:
jffs2_build_filesystem(): erasing all blocks after the end marker...
jffs2: Erase at 0x009e0000 failed immediately: -EROFS. Is the sector locked?
Ref: http://lists.infradead.org/pipermail/openwrt-devel/2020-January/021344.html
Reported-by: Steve Brown <sbrown@ewol.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
In zynq target, the DEVICE_DTS variable is always set consistent
with the model part of the device definition name.
This patch replaces the redundant definitions for the individual
devices with a common recipe.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
For the mvebu target in particular, there is a lot of files in
base-files that are only relevant for one subtarget. Improve
overview and reduce size per subtarget by moving/splitting
base-files depending on the subtarget they belong to.
While at it, consolidate 01_leds by using the model part of
the board name as variable.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
This introduces the SOC variable to mvebu target to derive some of
the DEVICE_DTS variables based on the SOC prefix and the device
definition name.
Since DTS names and compatible are inconsistent also in the kernel
for this target, the scheme cannot be applied to all devices, though.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
This moves the if conditions for choosing which image Makefiles
are used to the parent image/Makefile. It seems more convenient
to have "codeflow" in the parent while the subtarget-specific
files only contain the definitions.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
This device is an LTE router supported in ar71xx so far.
As per original commit, hardware specifications (v1.0 EU):
- SoC: QCA9531
- Flash: Winbond W25Q64FV (8MiB)
- RAM: EtronTech EM6AB160TSE-5G (64MiB)
- Wireless: SoC platform only (2.4GHz b/g/n, 2x internal antenna)
- Ethernet: 2NIC (3x100M + 1x100M)
- WWAN: TP-LINK LTE MODULE (2x external detachable antenna)
- Power: DC 12V 1A
Flashing instructions:
You can flash via tftp recovery (serve factory image as /mr6400_tp_recovery.bin
on 192.168.0.66/24, connect to any ethernet port and power on device while
holding the reset button). Flashing via OEM web interface does not work.
Known issues:
- LTE module does not always come up during boot (showing USB enumeration errors). Similar behavior has been reported at least from one user for ar71xx, too. Turning USB off and on again will serve as a workaround.
- eth0 (LAN) always shows carrier as 1 even if no cable is plugged in (this works "correctly" on ar71xx)
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
[several adjustments]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Filip Moc <lede@moc6.cz>
When mapping for RSSI LEDs was defined for interface wlan0 on
Ubiquiti Rocket M Titanium, it missed connection to actual interface.
Therefore create the mapping to interface, so RSSI LEDs work without
additional configuration, after starting rssileds service.
While at that, split RSSI into ~equal intervals for 6 LEDs,
and remove coefficients needed for PWM LEDs, as this board does not
support PWM LEDs.
Finally, for complete support, enable 'rssileds' package in per-device
rootfs, so the indicator works out of box.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Kernel partition increase to 4 MiBs for Netgear WNDR3700v4 and WNDR4300
routers breaks sysupgrade image compatibility with ar71xx builds.
Therefore, SUPPORTED_DEVICES variable has to be removed for both devices
from target makefile.
Reported-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
Currently it's not possible to effectively mark a "firmware" partition
as read-only. The sub-partitions "kernel", "rootfs" and "rootfs_data"
are always created as read-write (ignoring the parent access mode).
This patch enforces the access mode of sub-partitions to match the
parent partition, which is useful for recovery images that are meant
to be fully read-only to avoid accidental damage from end-user.
An example of such implementation (read-only firmware image) is the
recovery image used on the Zsun-SD100 [1].
Please note the related patch for fstools [2] to enable this read-only
concept.
[1] https://github.com/brunompena/zsun-resources
[2] http://lists.infradead.org/pipermail/openwrt-devel/2020-January/021043.html
Signed-off-by: Bruno Pena <brunompena@gmail.com>
[removed already obsolete 4.9 kernel patch]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
The Netgear WN2500RP V1 switch0 already works for LAN
however the port order for the LAN ports is inverted. Correct
physical port order watched from the back of the device is:
4 / 3 / 2 / 1
WAN port is absent on this device and therefore removed
from switch config.
Signed-off-by: Walter Sonius <walterav1984@gmail.com>
[move block to maintain alphabetic sorting]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The device tree property "mediatek,led_polarity" is ignored for
MT7628AN and MT7688. According to the datasheet both SoCs have
the matching register. Therefore the property should be applied
on these two devices as well.
Signed-off-by: Maximilian Pachl <m@ximilian.info>
Reviewed-by: Sungbo Eo <mans0n@gorani.run>
Tested-by: Sungbo Eo <mans0n@gorani.run>
Change the LED labels for hdd1/hdd2 in 01_leds to match their
counterpart in DTS.
Signed-off-by: Stephan Knauss <openwrt@stephans-server.de>
[improve commit title and message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The Netgear WNR3500 V2 switch0 already works for WAN/LAN
however the port order for the LAN ports is inverted. Correct
physical port order watched from the back of the device is:
Internet / 4 / 3 / 2 / 1 this resembles the Linksys E3000 V1.
Verfied with imagebuilder edit FILES=/etc/board.d/01_network
Signed-off-by: Walter Sonius <walterav1984@gmail.com>
Specification:
SoC: MediaTek MT7628AN
RAM: 64MiB
Flash: 8MiB
Wifi:
- 2.4GHz: MT7628AN
- 5GHz: MT7612EN
LAN: 1x 10/100 Mbps
Flash instructions:
Flash factory image through stock firmware WEB UI.
Back to stock is possible by using TFTP and stripping down the Firmware
provided by TP-Link to a initramfs.
The flash space between 0x650000 and 0x7f0000
is blank in the stock firmware so I left it out as well.
Signed-off-by: Steffen Förster <nemesis@chemnitz.freifunk.net>
Most of the kernel version switches below 4.14 were removed in commit
97940f8766 ("kernel: remove obsolete kernel version switches"),
but some of them still remained. Remove them now.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Using the led_ prefix for the node label is now common in ath79,
so also apply it here.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Using the LED of network interfaces for status (boot/failsafe/...)
indication is somewhat misleading, as the blinking might be
mistaken for network activity. This uses rssi LEDs instead, which
do not blink normally and thus are less ambiguous.
The rssihigh LED has also been used consistently for the TP-Link CPE
devices.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
"#mediatek,portmap" is not a valid property name.
If mediatek,portmap equals 0x0, then the esw driver ditches it and uses
the default value, 0x3f.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
mt76x8 uses esw_rt3050 driver, which does not accept mediatek,portmap with
string values. Convert the strings to integers to make it work.
According to its switch setup, WRTnode 2P/2R have a WAN port at port 0,
so the correct value should be 0x3e.
tplink_8m.dtsi uses "llllw", but it does not match switch setups of any
device using the DTSI. Remove it from the DTSI and add correct value to DTS
for each device.
These devices have a WAN port at port 0. Set the value to 0x3e.
- tplink,archer-c20-v4
- tplink,archer-c50-v3
- tplink,tl-mr3420-v5
- tplink,tl-wr840n-v4
- tplink,tl-wr841n-v13
- tplink,tl-wr842n-v5
These devices have only one ethernet port. They don't need portmap setting.
- tplink,tl-wa801nd-v5
- tplink,tl-wr802n-v4
- tplink,tl-wr902ac-v3
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
mt7620 and mt7621 use mt7530 driver, which only accepts "llllw", "wllll",
and "lwlll" values.
According to its switch setup, Mi Router 3G v2 has a WAN port at port 4,
so the correct value should be "llllw".
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
- fix color and active mode for existing wps led
- add green wps led
- add wps button
Signed-off-by: Jan Alexander <jan@nalx.net>
[wrap line]
Signed-off-by: David Bauer <mail@david-bauer.net>
Do not put usb-phy into reset if clearing the usb-phy reset or
setting the suspend_override has failed.
Reorder (de)asserts like in arch/mips/ath79/dev-usb.c.
Add an optional reset_control "usb-phy-analog", which is needed for
ar934x SoCs like in the old mach-driver arch/mips/ath79/dev-usb.c.
Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de>
This image is only needed on one device (wAP AC); since this target is
going to be removed anyway it doesn't make sense to add an extra "low
RAM" image.
Fixes OOM issues on RouterBoard wAP AC.
Signed-off-by: Thomas Nixon <tom@tomn.co.uk>
Change the caldata partition DTS node label to be consistent with
the label property for some Netgear WNDR devices.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This patch introduces support for Netgear WNDR4500v3. Router
is very similar to WNDR4300v2 and is based on the same PCB.
Information gathered from various Internet sources (including
https://patchwork.ozlabs.org/patch/809227/) shows following
differences to WNDR4300v2:
* two USB 2.0 ports with separate LEDs
* USB LEDs soldered to secondary pads
* WPS and RFKILL buttons soldered to secondary pads
* described as N900 device with 3x3:3 MIMO for 2.4GHz radio
* power supply requirement is DC 12V 2.5A
* vendor HW ID suffix differs in one digit
* bigger chassis
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
This patch introduces support for Netgear WNDR4300v2.
Specification
=============
* Description: Netgear WNDR4300 v2
* Loader: U-boot
* SOC: Qualcomm Atheros QCA9563 (775 MHz)
* RAM: 128 MiB
* Flash: 2 MiB SPI-NOR + 128 MiB SPI-NAND
- NOR: U-boot binary: 256 KiB
- NOR: U-boot environment: 64 KiB
- NOR: ART Backup: 64 KiB
- NOR: Config: 64 KiB
- NOR: Traffic Meter: 64 KiB
- NOR: POT: 64 KiB
- NOR: Reserved: 1408 KiB
- NOR: ART: 64 KiB
- NAND: Firmware: 25600 KiB (see notes for OpenWrt)
- NAND: Language: 2048 KiB
- NAND: mtdoops Crash Dump: 128 KiB
- NAND: Reserved: 103296 KiB
* Ethernet: 5 x 10/100/1000 (4 x LAN, 1 x WAN) (AR8337)
* Wireless:
- 2.4 GHz b/g/n (internal)
- 5 GHz a/n (AR9580)
* USB: yes, 1 x USB 2.0
* Buttons:
- Reset
- WiFi (rfkill)
- WPS
* LEDs:
- Power (amber/green)
- WAN (amber/green)
- WLAN 2G (green)
- WLAN 5G (blue)
- 4 x LAN (amber/green)
- USB (green)
- WPS (green)
* UART: 4-pin connector JP1, 3.3V (Vcc, TX, RX, GND), 115200 8N1
* Power supply: DC 12V 1.5A
* MAC addresses: LAN=WLAN2G on case label, WAN +1, WLAN5G +2
Important Notes
===============
0. NOR Flash (2 MiB) is not touched by OpenWrt installation.
1. NAND Flash (128 MiB) layout under OpenWrt is changed as follows:
all space is split between 4 MiB kernel and 124 MiB UBI areas;
vendor partitions (language and mtdoops) are removed; kernel space
size can be further expanded if needed; maximum image size is set
to 25600k for compatibility reasons and can also be increased.
2. CPU clock is 775 MHz, not 750 MHz.
3. 5 GHz wireless radio chip is Atheros AR9580-AR1A with bogus PCI
device ID 0xabcd. For ath9k driver to load successfully, this is
overriden in DTS with correct value for this chip, 0x0033.
4. RFKILL button is wired to AR9580 pin 9 which is normally disabled
by chip definition in ath9k code (0x0000F4FF gpio mask). Therefore
'qca,gpio-mask=<0xf6ff>' hack must be used for button to work
properly.
5. USB port is always on, no GPIO for 5V power control has been
identified.
Installation
============
* TFTP recovery
* TFTP via U-boot prompt
* sysupgrade
* Web interface
Test build configuration
========================
CONFIG_TARGET_ath79=y
CONFIG_TARGET_ath79_nand=y
CONFIG_TARGET_ath79_nand_DEVICE_netgear_wndr4300-v2=y
CONFIG_ALL_KMODS=y
CONFIG_DEVEL=y
CONFIG_CCACHE=y
CONFIG_COLLECT_KERNEL_DEBUG=y
CONFIG_IMAGEOPT=y
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
This commit adds support for the D-Link DIR-505, previously supported in
ar71xx.
Hardware
--------
SoC: Atheros AR9330
FLASH: 8M SPI-NOR
RAM: 64M
WIFI: 1T1R 1SS Atheros AR9330
LED: Power green, Status red
BTN: WPS, Reset
Installation
------------
Currently, installation is only possible by sysupgrading from an earlier
OpenWrt version, U-Boot TFTP or a modded U-Boot. I do not have the
original bootloader from D-Link on my device anymore, so i cannot test
the factory image.
Signed-off-by: David Bauer <mail@david-bauer.net>
The present U-Boot for GL-AR750S has a limit of 2 MB for kernel size.
While sysupgrade can manage kernels up to the present limit of 4 MB,
directly flashing a factory.img with a kernel size greater than 2 MB
through U-Boot will result in an unbootable device.
This commit uses the newly-introduced check-kernel-size build
operation to prevent the output of factory.img when the kernel
exceeds 2 MB in size, yet permits output of sysupgrade.img
as long as the kernel is within KERNEL_SIZE := 4096k
Cc: Chuanhong Guo <gch981213@gmail.com>
Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
The memory hacks got removed from ath10k with 1e27bef ("mac80211: remove
ath10k_pci memory hacks"). As this device has low amount of RAM, switch
to ath-10k-ct small buffers variant, to avoid the OOM Reaper.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
This reorganizes 02_network board.d files based on what's done for
ath79 and ramips: Instead of putting all settings into a single big
case, the interface/dsl/MAC address setup is put into separate
functions with a specific switch case for each of them. This makes
grouping of devices much easier and should be easier to read, too.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
DSL setup consists of the same commands for all subtargets, so move it
into a helper function.
While at it, remove shebang from library file.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This splits the device-dependent base-files into subtarget directories,
like done recently for ath79 and ramips. While this increases the
overall lines of codes, it will make the code per subtarget smaller
and easier to keep track of features and devices.
While at it, several variables at the top of 02_network are removed,
as they were never changed. The values are put directly into the
function calls where they are used.
Remove unneeded LED setup from 01_leds, and remove 01_leds entirely
for falcon subtarget (as it is not used there).
Applies alphabetic reordering to device cases in base-files.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This splits some base-files across subtargets, as done previously
on ath79 and ramips and also introduced for mt7629 subtarget here
already. Most of the existing base-files content is specific to
mt7623.
While at it, apply the following fixes:
- Remove lots of trailing whitespaces
- Remove wildcard on unielec,u7623-02-emmc-512m
- Remove inconsistent quotation marks in cases
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: John Crispin <john@phrozen.org>
The Aruba AP-303H is the hospitality version of the Aruba AP-303 with a
POE-passthrough enabled ethernet switch instead of a sigle PHY.
Hardware
--------
SoC: Qualcomm IPQ4029
RAM: 512M DDR3
FLASH: - 128MB SPI-NAND (Macronix)
- 4MB SPI-NOR (Macronix MX25R3235F)
TPM: Atmel AT97SC3203
BLE: Texas Instruments CC2540T
attached to ttyMSM1
ETH: Qualcomm QCA8075
LED: WiFi (amber / green)
System (red / green /amber)
PSE (green)
BTN: Reset
USB: USB 2.0
To connect to the serial console, you can solder to the labled pads next
to the USB port or use your Aruba supplied UARt adapter.
Do NOT plug a standard USB cable into the Console labled USB-port!
Aruba/HPE simply put UART on the micro-USB pins. You can solder yourself
an adapter cable:
VCC - NC
D+ - TX
D- - RX
GND - GND
The console setting in bootloader and OS is 9600 8N1. Voltage level is
3.3V.
To enable a full list of commands in the U-Boot "help" command, execute
the literal "diag" command.
Installation
------------
1. Get the OpenWrt initramfs image. Rename it to ipq40xx.ari and put it
into the TFTP server root directory. Configure the TFTP server to
be reachable at 192.168.1.75/24. Connect the machine running the TFTP
server to the E0 (!) ethernet port of the access point, as it only
tries to pull from the WAN port.
2. Connect to the serial console. Interrupt autobooting by pressing
Enter when prompted.
3. Configure the bootargs and bootcmd for OpenWrt.
$ setenv bootargs_openwrt "setenv bootargs console=ttyMSM0,9600n8"
$ setenv nandboot_openwrt "run bootargs_openwrt; ubi part aos1;
ubi read 0x85000000 kernel; set fdt_high 0x87000000;
bootm 0x85000000"
$ setenv ramboot_openwrt "run bootargs_openwrt;
setenv ipaddr 192.168.1.105; setenv serverip 192.168.1.75;
netget; set fdt_high 0x87000000; bootm"
$ setenv bootcmd "run nandboot_openwrt"
$ saveenv
4. Load OpenWrt into RAM:
$ run ramboot_openwrt
5. After OpenWrt booted, transfer the OpenWrt sysupgrade image to the
/tmp folder on the device. You will need to plug into E1-E3 ports of
the access point to reach OpenWrt, as E0 is the WAN port of the
device.
6. Flash OpenWrt:
$ ubidetach -p /dev/mtd16
$ ubiformat /dev/mtd16
$ sysupgrade -n /tmp/openwrt-sysupgrade.bin
To go back to the stock firmware, simply reset the bootcmd in the
bootloader to the original value:
$ setenv bootcmd "boot"
$ saveenv
Signed-off-by: David Bauer <mail@david-bauer.net>
The Ubiquiti ToughSwitch 5XP is a 5-port PoE Gigabit switch with a single
Fast-Ethernet management port. It supports both 24V passive PoE out on all
five ports.
Flash: 8 MB
RAM: 64 MB
SoC: AR7242
Switch: ar8327
USB: 1x USB 2.0
Ethernet: 5x GbE, 1x FE
Installation of the firmware is possible either via serial + tftpboot or
the factory firmware update function via webinterface.
By default the single Fast-Ethernet port labeled "MGMT" is configured
as the WAN port. Thus access to the device is only possible via the
five switch ports.
Serial: 3v3 115200 8n1
The serial header is located in the lower left corner of the switches PCB:
```
|
|
|
| o
| o RX
| o TX
| o GND
|
|
++ +-++-+ ++ ++ +
+--+ ++ +--++--++--+
```
Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
[remove ubnt,sw compatible - fix spelling - wrap commit message -
remove superfluous phy-mode property]
Signed-off-by: David Bauer <mail@david-bauer.net>
This device OOPs during the boot due to broken flash. It can be probably
fixed with `broken-flash-reset` once ramips is on 4.19 kernel.
So disable images for this device until its fixed.
Ref: FS#2695, PR#2483
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Builds for kenrel 4.14 targetswere failing because of
missing symbols for the B53 swconfig driver.
Fixes: 313bde53ce ("generic: update config-4.19")
Signed-off-by: David Bauer <mail@david-bauer.net>
Hardware:
SOC: Qualcomm IPQ4018
RAM: 128 MB Nanya NT5CC64M16GP-DI
FLASH: 16 MB Macronix MX25L12805D
ETH: Qualcomm QCA8075 (4 Gigabit ports, 3xLAN, 1xWAN)
WLAN: Qualcomm IPQ4018 (2.4 & 5 Ghz)
BUTTON: Shared WPS/Reset button
LED: RGB Status/Power LED
SERIAL: Header J8 (UART, Left side of board). Numbered from
top to bottom:
(1) GND, (2) TX, (3) RX, (4) VCC (White triangle
next to it).
3.3v, 115200, 8N1
Tested/Working:
* Ethernet
* WiFi (2.4 and 5GHz)
* Status LED
* Reset Button (See note below)
Implementation notes:
* The shared WPS/Reset button is implemented as a Reset button
* I could not find a original firmware image to reverse engineer, meaning
currently it's not possible to flash OpenWrt through the Web GUI.
Installation (Through Serial console & TFTP):
1. Set your PC to fixed IP 192.168.1.12, Netmask 255.255.255.0, and connect to
one of the LAN ports
2. Rename the initramfs image to 'C0A8010B.img' and enable a TFTP server on
your pc, to serve the image
2. Connect to the router through serial (See connection properties above)
3. Hit a key during startup, to pause startup
4. type `setenv serverip 192.168.1.12`, to set the tftp server address
5. type `tftpboot`, to load the image from the laptop through tftp
6. type `bootm` to run the loaded image from memory
6. (If you want to return to stock firmware later, create an full MTD backup,
e.g. using instructions here https://openwrt.org/docs/guide-user/installation/generic.backup#create_full_mtd_backup)
7. Transfer the 'sysupgrade' OpenWrt firmware image from PC to router, e.g.:
`scp xxx-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/upgrade.bin`
8. Run sysupgrade to permanently install OpenWrt to flash: `sysupgrade -n /tmp/upgrade.bin`
Revert to stock:
To revert to stock, you need the MTD backup from step 6 above:
1. Unpack the MTD backup archive
2. Transfer the 'firmware' partition image to the router (e.g. mtd8_firmware.backup)
3. On the router, do `mtd write mtd8_firmware.backup firmware`
Signed-off-by: Tom Brouwer <tombrouwer@outlook.com>
[removed BOARD_NAME, OpenWRT->OpenWrt, changed LED device name to board name]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch partially reverts
"ipq40xx: remove unnecessary usb nodes in DTS for ASUS RT-AC58U"
as the change removed the usb2 port-trigger, so the LED would no
longer light-up when a USB 2.0 was inserted into the USB port.
Fixes: d0efb1ba95 ("ipq40xx: remove unnecessary usb nodes in DTS for ASUS RT-AC58U")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Flash: 8 MB
RAM: 64 MB
SoC: AR7242
Switch: bcm53128
USB: 1x USB 2.0
Ethernet: 8x GbE, 1x FE
The Ubiquiti ToughSwitch 8XP is a 8-port PoE Gigabit switch with a single
Fast-Ethernet management port. It supports both 24V passive PoE and 48V
802.11af/at PoE out on all eight ports.
By default the single Fast-Ethernet port labeled "MGMT" is configured as the
WAN port. Thus access to the device is only possible via the eight switch
ports.
Installation of the firware is possible either via serial + tftpboot or
the factory firmware update function via webinterface.
Serial: 3v3 115200 8n1
The serial header is located in the lower left corner of the switches PCB:
|
|
|
| o
| o RX
| o TX
| o GND
|
|
++ +-++-+ ++ ++ +
+--+ ++ +--++--++--+
Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
[fix whitespace issue]
Signed-off-by: David Bauer <mail@david-bauer.net>
SW devices are Ubiquit ToughSwitch and EdgeSwitch series devices.
Hardware-wise they are very similar to the XM device series.
Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
This commit fixes a bug in the main swconfig patch where a function
needed by the b53 driver is not exported.
Additionally it adds OF support to the b53_mdio driver for devicetree-
based probing
Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
u-boot splits nand factory firmware at 2M offset, flash the first
part as kernel into spi nor and the other part as ubi into nand
flash. With previous commit increasing kernel size to 4M, generated
factory firmware is broken because ubi is at 4M offset.
This commit reduces kernel size definition to 2M in image Makefile,
producing proper factory image. Partition size in dts is kept
unchanged so that sysupgrade to a firmware with 2M+ kernel still
works.
Fixes: b496a2294c ("ath79: GL-AR750S: provide NAND support; increase kernel to 4 MB")
Reported-by: Jeff Kletsky <git-commits@allycomm.com>
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
TP-Link Archer C20 v5 is a router with 5-port FE switch and
non-detachable antennas. It's based on MediaTek MT7628N+MT7610EN.
Specification:
- MediaTek MT7628N/N (580 Mhz)
- 64 MB of RAM
- 8 MB of FLASH
- 2T2R 2.4 GHz and 1T1R 5 GHz
- 5x 10/100 Mbps Ethernet
- 3x external, non-detachable antennas
- UART (J1) header on PCB (115200 8n1)
- 7x LED (GPIO-controlled*), 2x button, power input switch
* WAN LED in this devices is a dual-color, dual-leads type which isn't
(fully) supported by gpio-leds driver. This type of LED requires both
GPIOs state change at the same time to select color or turn it off.
For now, we support/use only the green part of the LED.
Create Factory image
--------------------
As all installation methods require a U-Boot to be integrated into the
Image (and we do not ship one with the image) we are not able to create
an image in the OpenWRT build-process.
Download a TP-Link image from their Website and a OpenWRT sysupgrade
image for the device and build yourself a factory image like following:
TP-Link image: tpl.bin
OpenWRT sysupgrade image: owrt.bin
> dd if=tpl.bin of=boot.bin bs=131584 count=1
> cat owrt.bin >> boot.bin
Installing via Web-UI
---------------------
Upload the boot.bin via TP-Links firmware upgrade tool in the
web-interface.
Installing via Recovery
-----------------------
Activate Web-Recovery by beginning the upgrade Process with a
Firmware-Image from TP-Link. After starting the Firmware Upgrade,
wait ~3 seconds (When update status is switching to 0%), then
disconnect the power supply from the device. Upgrade flag (which
activates Web-Recovery) is written before the OS-image is touched and
removed after write is succesfull, so this procedure should be safe.
Plug the power back in. It will come up in Recovery-Mode on 192.168.0.1.
When active, all LEDs but the WPS LED are off.
Remeber to assign yourself a static IP-address as DHCP is not active in
this mode.
The boot.bin can now be uploaded and flashed using the web-recovery.
Installing via TFTP
-------------------
Prepare an image like following (Filenames from factory image steps
apply here)
> dd if=/dev/zero of=tp_recovery.bin bs=196608 count=1
> dd if=tpl.bin of=tmp.bin bs=131584 count=1
> dd if=tmp.bin of=boot.bin bs=512 skip=1
> cat boot.bin >> tp_recovery.bin
> cat owrt.bin >> tp_recovery.bin
Place tp_recovery.bin in root directory of TFTP server and listen on
192.168.0.66/24.
Connect router LAN ports with your computer and power up the router
while pressing the reset button. The router will download the image via
tftp and after ~1 Minute reboot into OpenWRT.
U-Boot CLI
----------
U-Boot CLI can be activated by holding down '4' on bootup.
Dual U-Boot
-----------
This is TP-Link MediaTek device with a split-uboot feature design like
a TP-Link Archer C50 v4. The first (factory-uboot) provides recovery via
TFTP and HTTP, jumping straight into the second (firmware-uboot) if no
recovery needs to be performed. The firmware-uboot unpacks and executed
the kernel.
Web-Recovery
------------
TP-Link integrated a new Web-Recovery like the one on the Archer C7v4 /
TL-WR1043v5 / Archer C50v4. Stock-firmware sets a flag in the "romfile"
partition before beginning to write and removes it afterwards. If the
router boots with this flag set, bootloader will automatically start
Web-recovery and listens on 192.168.0.1. This way, the vendor-firmware
or an OpenWRT factory image can be written.
By doing the same while performing sysupgrade, we can take advantage of
the Web-recovery in OpenWRT.
It is important to note that Web-Recovery is only based on this flag. It
can't detect e.g. a crashing kernel or other means. Once activated it
won't boot the OS before a recovery action (either via TFTP or HTTP) is
performed. This recovery-mode is indicated by an illuminated WPS-LED on
boot.
Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
[adjust some node names for LEDs in DTS]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
- add "gpio" group for wan_orange led
- use tpt triggers for wifi led indication
- add wifi 5 GHz led support
Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
[slight commit message adjustment]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Image builds for the ramips-mt7621 target currently fail with:
> WARNING: Image file ./hiwifi_hc5962-kernel.bin is too big
Disable this board for now. It can still be built using the SDK.
Signed-off-by: David Bauer <mail@david-bauer.net>
This target is still on kernel 4.9, and it looks like there is no
active maintainer for this target anymore.
Remove the code and all the packages which are only used by this target.
To add this target to OpenWrt again port it to a recent and supported
kernel version.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This target seems to have been unmaintained for quite a while, and not a
single tester for the (now outdated) kernel 4.14 patches has been found.
Remove the code and all the packages which are only used by this target.
To add this target to OpenWrt again port it to a recent and supported
kernel version.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This target seems to have been unmaintained for quite a while, and not a
single tester for the (now outdated) kernel 4.14 patches has been found.
Remove the code and all the packages which are only used by this target.
To add this target to OpenWrt again port it to a recent and supported
kernel version.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This adds support for kernel 4.14 to the target and directly make it the
default kernel version to use.
This patch is build-tested only, but has never been device-tested. It is
only added to preserve the changes in Git history prior to removing this
target. Use it with care.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
[rebased and extended commit message, refreshed patches for 4.14.162]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The configuration of the generic subtarget was used as the default
configuration and then the subtarget configurations were adapted.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This adds support for kernel 4.14 to the target and directly make it the
default kernel version to use.
This patch is build-tested only, but has never been device-tested. It is
only added to preserve the changes in Git history prior to removing this
target. Use it with care.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
[rebased and extended commit message, refreshed patches for 4.14.162]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The configuration of the generic subtarget was used as the default
configuration and then the subtarget configurations were adapted.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The device label shows the address currently assigned to the OpenWrt
LAN interface.
Current setup is:
LAN *:b8 factory 0xe006 label
WAN *:b7 factory 0xe000
For vendor FW bootlog we get (manually removed parts of the address):
[ 7.520000] set LAN/WAN LWLLL
[ 7.530000] GMAC1_MAC_ADRH -- : 0x00004031
[ 7.530000] GMAC1_MAC_ADRL -- : 0x3c****b7
[ 7.530000] GDMA2_MAC_ADRH -- : 0x00004031
[ 7.540000] GDMA2_MAC_ADRL -- : 0x3c****b8
[ 7.540000] eth1: ===> VirtualIF_open
Without further information, this does not allow verification of
the currently unexpected LAN/WAN assignment (we would expect 0xe000
to be LAN).
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This move the slightly different target-specific implementations of
mktplinkfw from the targets to include/image-commands.mk and renames
it to tplink-v1-image. Having a common version will increase
consistency between implementation and will complete the
tplink build command already present in the new location.
Due to the slight differences of the original implementations, this
also does some adjustments to the device build commands/variables.
This also moves rootfs_align as this is required as dependency.
Tested on:
- TL-WDR4300 v1 (ath79, factory)
- TL-WDR4900 v1 (mpc85xx, sysupgrade)
- RE210 v1 (ramips, see Tested-by)
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Christoph Krapp <achterin@googlemail.com>
Martin Schiller
Aleksander Jan Bajkowski
Hauke Mehrtens
Adrian Schmutzler
Pawel Dembicki
Daniel Golle
DENG Qingfang
Petr Štetiar
David Bauer
Sven Roederer
Mathias Kresin
Rafał Miłecki
Sungbo Eo
Christian Buschau
Chuanhong Guo
Lech Perczak
Dan Haab
INAGAKI Hiroshi
Álvaro Fernández Rojas
Koen Vandeputte
Michal Cieslakiewicz
John Crispin
August Huber
Tomasz Maciej Nowak
Andreas Böhler
Kevin Darbyshire-Bryant
Roger Pueyo Centelles
Jan Alexander
Sven Roederer
Scott Roberts
Christian Lamparter
Yen-Ting-Shen
Fredrik Olofsson
Felix Fietkau
Kimmo Vuorinen
Jonas Gorski
Russell King
Enrico Mioso
Bruno Pena
Walter Sonius
Maximilian Pachl
Stephan Knauss
Steffen Förster
Johann Neuhauser
Thomas Nixon
Jeff Kletsky
Tobias Schramm
Tom Brouwer
Maxim Anisimov
Hauke Mehrtens