This commit adds the ability to set custom uImage magic to
Build/wr1201-factory-header and renames it to
"Build/custom-initramfs-uimage".
Custom uImage header in initramfs image is required on following
devices:
- I-O DATA WN-AX1167GR2
- I-O DATA WN-AX2033GR
- I-O DATA WN-AX2033GR2
- I-O DATA WN-DX1167R
While at it, fix typo in comment.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Reviewed-by: Sungbo Eo <mans0n@gorani.run>
[shorten commit title, minor commit message adjustments]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
TP-Link RE200 v2 is a wireless range extender with Ethernet and 2.4G and 5G
WiFi with internal antennas. It's based on MediaTek MT7628AN+MT7610EN.
Specifications
--------------
- MediaTek MT7628AN (580 Mhz)
- 64 MB of RAM
- 8 MB of FLASH
- 2T2R 2.4 GHz and 1T1R 5 GHz
- 1x 10/100 Mbps Ethernet
- UART header on PCB (57600 8n1)
- 8x LED (GPIO-controlled), 2x button
There are 2.4G and 5G LEDs in red and green which are controlled
separately.
MAC addresses
-------------
The MAC address assignment matches stock firmware, i.e.:
LAN : *:0D
2.4G: *:0E
5G : *:0F
Installation
------------
Web Interface
-------------
It is possible to upgrade to OpenWrt via the web interface. Simply flash
the -factory.bin from OEM. In contrast to a stock firmware, this will not
overwrite U-Boot.
Serial console
--------------
Opening the case is quite hard, since it is welded together. Rename the
OpenWrt factory image to "test.bin", then plug in the device and quickly
press "2" to enter flash mode (no line feed). Follow the prompts until
OpenWrt is installed.
Unfortunately, this devices does not offer a recovery mode or a tftp
installation method. If the web interface upgrade fails, you have to open
your device and attach serial console.
Additonal notes
---------------
It is possible to flash back to stock by using tplink-safeloader to create
a sysupgrade image based on a stock update. After the first boot, it is
necessary upgrade to another stock image, otherwise subsequent boots
fail with LZMA ERROR 1 and you have to attach serial to recover the device.
Signed-off-by: Andreas Böhler <dev@aboehler.at>
[remove DEVICE_VARS change]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This moves the various variants of common device definitions for
TP-Link devices to a common Makefile common-tp-link.mk. This
provides the opportunity to reorganize and move parameters between
individual device definitions and the common ones.
While at it, also use the common definitions for previously
independent definitions where appropriate.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
DEVICE_PACKAGES is specified twice for the same device. Remove the
first (=older) assignment.
Fixes: 40692f0fb5 ("ramips: mt7620: select only the matching mt76 driver")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The GL.iNet microuter-N300 (internally referred as MT300N-v4) is a
pocket-size travel router. It is essentially identical to the VIXMINI
(internally referred as MT300N-v3) but with double the RAM and
SPI-flash.
Additionally, set the label-mac for both the VIXMINI as well as the
microuter-N300.
Hardware
--------
SoC: MediaTek MT7628NN
RAM: 128M DDR2
FLASH: 16M
LED: Power - WLAN
BTN: Reset
UART: 115200 8N1
TX and RX are labled on the board as pads next to the SoC
Installation via web-interface
------------------------------
1. Visit the web-interface at 192.168.8.1
Note: The ethernet port is by default WAN. So you need to connect to
the router via WiFi
2. Navigate to the Update tab on the left side.
3. Select "Local Update"
4. Upload the OpenWrt sysupgrade image.
Note: Make sure you select not to preserve the configuration.
Installation via U-Boot
-----------------------
1. Hold down the reset button while powering on the device.
Wait for the LED to flash 5 times.
2. Assign yourself a static IPv4 in 192.168.1.0/24
3. Upload the OpenWrt sysupgrade image at 192.168.1.1.
Signed-off-by: David Bauer <mail@david-bauer.net>
In ramips, all devices in mt7621, mt76x8 and rt288x subtarget have
the same value set to the SOC variable for each device individually.
This patch introduces a non-device-dependent variable DEFAULT_SOC,
which is used if no specific SOC is set for a device, and thus reduces
the number of redundant definitions drastically.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Specification:
SoC: MediaTek MT7628AN
RAM: 64MiB
Flash: 8MiB
Wifi:
- 2.4GHz: MT7628AN
- 5GHz: MT7612EN
LAN: 1x 10/100 Mbps
Flash instructions:
Flash factory image through stock firmware WEB UI.
Back to stock is possible by using TFTP and stripping down the Firmware
provided by TP-Link to a initramfs.
The flash space between 0x650000 and 0x7f0000
is blank in the stock firmware so I left it out as well.
Signed-off-by: Steffen Förster <nemesis@chemnitz.freifunk.net>
This device OOPs during the boot due to broken flash. It can be probably
fixed with `broken-flash-reset` once ramips is on 4.19 kernel.
So disable images for this device until its fixed.
Ref: FS#2695, PR#2483
Signed-off-by: Petr Štetiar <ynezz@true.cz>
TP-Link Archer C20 v5 is a router with 5-port FE switch and
non-detachable antennas. It's based on MediaTek MT7628N+MT7610EN.
Specification:
- MediaTek MT7628N/N (580 Mhz)
- 64 MB of RAM
- 8 MB of FLASH
- 2T2R 2.4 GHz and 1T1R 5 GHz
- 5x 10/100 Mbps Ethernet
- 3x external, non-detachable antennas
- UART (J1) header on PCB (115200 8n1)
- 7x LED (GPIO-controlled*), 2x button, power input switch
* WAN LED in this devices is a dual-color, dual-leads type which isn't
(fully) supported by gpio-leds driver. This type of LED requires both
GPIOs state change at the same time to select color or turn it off.
For now, we support/use only the green part of the LED.
Create Factory image
--------------------
As all installation methods require a U-Boot to be integrated into the
Image (and we do not ship one with the image) we are not able to create
an image in the OpenWRT build-process.
Download a TP-Link image from their Website and a OpenWRT sysupgrade
image for the device and build yourself a factory image like following:
TP-Link image: tpl.bin
OpenWRT sysupgrade image: owrt.bin
> dd if=tpl.bin of=boot.bin bs=131584 count=1
> cat owrt.bin >> boot.bin
Installing via Web-UI
---------------------
Upload the boot.bin via TP-Links firmware upgrade tool in the
web-interface.
Installing via Recovery
-----------------------
Activate Web-Recovery by beginning the upgrade Process with a
Firmware-Image from TP-Link. After starting the Firmware Upgrade,
wait ~3 seconds (When update status is switching to 0%), then
disconnect the power supply from the device. Upgrade flag (which
activates Web-Recovery) is written before the OS-image is touched and
removed after write is succesfull, so this procedure should be safe.
Plug the power back in. It will come up in Recovery-Mode on 192.168.0.1.
When active, all LEDs but the WPS LED are off.
Remeber to assign yourself a static IP-address as DHCP is not active in
this mode.
The boot.bin can now be uploaded and flashed using the web-recovery.
Installing via TFTP
-------------------
Prepare an image like following (Filenames from factory image steps
apply here)
> dd if=/dev/zero of=tp_recovery.bin bs=196608 count=1
> dd if=tpl.bin of=tmp.bin bs=131584 count=1
> dd if=tmp.bin of=boot.bin bs=512 skip=1
> cat boot.bin >> tp_recovery.bin
> cat owrt.bin >> tp_recovery.bin
Place tp_recovery.bin in root directory of TFTP server and listen on
192.168.0.66/24.
Connect router LAN ports with your computer and power up the router
while pressing the reset button. The router will download the image via
tftp and after ~1 Minute reboot into OpenWRT.
U-Boot CLI
----------
U-Boot CLI can be activated by holding down '4' on bootup.
Dual U-Boot
-----------
This is TP-Link MediaTek device with a split-uboot feature design like
a TP-Link Archer C50 v4. The first (factory-uboot) provides recovery via
TFTP and HTTP, jumping straight into the second (firmware-uboot) if no
recovery needs to be performed. The firmware-uboot unpacks and executed
the kernel.
Web-Recovery
------------
TP-Link integrated a new Web-Recovery like the one on the Archer C7v4 /
TL-WR1043v5 / Archer C50v4. Stock-firmware sets a flag in the "romfile"
partition before beginning to write and removes it afterwards. If the
router boots with this flag set, bootloader will automatically start
Web-recovery and listens on 192.168.0.1. This way, the vendor-firmware
or an OpenWRT factory image can be written.
By doing the same while performing sysupgrade, we can take advantage of
the Web-recovery in OpenWRT.
It is important to note that Web-Recovery is only based on this flag. It
can't detect e.g. a crashing kernel or other means. Once activated it
won't boot the OS before a recovery action (either via TFTP or HTTP) is
performed. This recovery-mode is indicated by an illuminated WPS-LED on
boot.
Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
[adjust some node names for LEDs in DTS]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Image builds for the ramips-mt7621 target currently fail with:
> WARNING: Image file ./hiwifi_hc5962-kernel.bin is too big
Disable this board for now. It can still be built using the SDK.
Signed-off-by: David Bauer <mail@david-bauer.net>
This move the slightly different target-specific implementations of
mktplinkfw from the targets to include/image-commands.mk and renames
it to tplink-v1-image. Having a common version will increase
consistency between implementation and will complete the
tplink build command already present in the new location.
Due to the slight differences of the original implementations, this
also does some adjustments to the device build commands/variables.
This also moves rootfs_align as this is required as dependency.
Tested on:
- TL-WDR4300 v1 (ath79, factory)
- TL-WDR4900 v1 (mpc85xx, sysupgrade)
- RE210 v1 (ramips, see Tested-by)
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Christoph Krapp <achterin@googlemail.com>
ipTIME A8004T is a 2.4/5GHz band AC2600 router, based on Mediatek
MT7621A.
Specifications:
- SoC: MT7621A
- RAM: DDR3 256M
- Flash: SPI NOR 16MB
- WiFi:
- 2.4GHz: MT7615E
- 5GHz: MT7615E
- Ethernet: 5x 10/100/1000Mbps
- Switch: SoC internal
- USB: 1 * USB3.0 port
- UART:
- J4: 3.3V, TX, RX, GND (3.3V is the square pad) / 57600 8N1
- Other info:
- J9: Unknown unpopulated header.
Installation via web interface:
1. Flash **initramfs** image through the stock web interface.
2. Boot into OpenWrt and perform sysupgrade with sysupgrade image.
Revert to stock firmware:
1. Perform sysupgrade with stock image.
Signed-off-by: Yong-hyu Ban <perillamint@quendi.moe>
[do not enable xhci node in DTS which is already enabled in DTSI]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Currently this device fails to boot with the OpenWrt snapshot images
(release images are unaffected). The error message is:
"LZMA ERROR 1 - must RESET board to recover".
This happens because the kernel image is too big for the bootloader
to boot. This commit works around this by decreasing the lzma dictionary
size option from the default 23 to 10.
Before this change the current OpenWrt snapshot image (uncompressed
kernel size 4875139 bytes) failed to boot, while now an even bigger
image (kernel 4.19 with snapshot default config; uncompressed kernel
size 5162833 bytes) boots just fine.
The highest lzma dictionary size option this image booted with was 11.
10 was chosen to have a bit more room for growth.
An unavoidable side-effect of this change is that the compressed kernel
image will take up more space.
Total image size with different dictionary size options:
D23 - 3973903 bytes (base)
D16 - 4113167 bytes (+3.5% - +139264 bytes)
D12 - 4317967 bytes (+8.7% - +344064 bytes)
D11 - 4383503 bytes (+10.3% - +409600 bytes)
D10 - 4461327 bytes (+12.3% - +487424 bytes)
Fixes: FS#1484
Signed-off-by: Mason Clarke <mclarke2355@gmail.com>
Images generated for the TP-Link RE200v1 cannot be updated using
sysupgrade, because a necessary call to append-metadata was missing.
Signed-off-by: Andreas Böhler <dev@aboehler.at>
Edimax RA21S is a dual band 11ac router,
based on MediaTek MT7621A and MT7615N chips.
Specification:
- SoC: MediaTek MT7621A dual-core @ 880MHz
- RAM: 256M (Nanya NT5CC128M16IP)
- FLASH: 16MB (Macronix MX25L12835F)
- WiFi: 2.4/5 GHz 4T4R
- 2.4GHz MediaTek MT7615N bgn
- 5GHz MediaTek MT7615N nac
- Switch: SoC integrated Gigabit Switch (4 x LAN, 1 x WAN)
- USB: No
- BTN: Reset, WPS
- LED: 4 red LEDs, indistinguishable when case closed
- UART: through-hole on PCB.
J1: 3.3V - RX - GND - TX / 57600-8N1. 3.3V is the square pad
Installation:
Update the factory image via the OEM web-interface
(by default: http://192.168.2.1/)
User: admin
Password: 1234
The sysupgrade image can be installed via TFTP
from the U-Boot bootloader. Connect via ethernet port 2.
Tested on device by @UAb5eSMn
Signed-off-by: Maksym Medvedev <redrathnure@gmail.com>
[split DTS and take over improvements from RG21S, extend commit
message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
TP-Link RE200 v1 is a wireless range extender with Ethernet and 2.4G and 5G
WiFi with internal antennas. It's based on MediaTek MT7620A+MT7610EN.
Specifications
--------------
- MediaTek MT7620A (580 Mhz)
- 64 MB of RAM
- 8 MB of FLASH
- 2T2R 2.4 GHz and 1T1R 5 GHz
- 1x 10/100 Mbps Ethernet
- UART header on PCB (57600 8n1)
- 8x LED (GPIO-controlled; only 6 supported), 2x button
There are 2.4G and 5G LEDs in red and green which are controlled
separately. The 5G LED is currently not supported, since the GPIOs couldn't
be determined.
Installation
------------
Web Interface
-------------
It is possible to upgrade to OpenWrt via the web interface. However, the
OEM firmware upgrade file is required and a tool to fix the MD5 sum of
the header. This procedure overwrites U-Boot and there is not failsafe /
recovery mode present! To prepare an image, you need to take the header
and U-Boot (i.e. 0x200 + 0x20000 bytes) from an OEM firmware file and
attach the factory image to it. Then fix the header MD5Sum1.
Serial console
--------------
Opening the case is quite hard, since it is welded together. Rename the
OpenWrt factory image to "test.bin", then plug in the device and quickly
press "2" to enter flash mode (no line feed). Follow the prompts until
OpenWrt is installed.
Unfortunately, this devices does not offer a recovery mode or a tftp
installation method. If the web interface upgrade fails, you have to open
your device and attach serial console. Since the web upgrade overwrites
the boot loader, you might also brick your device.
Additional notes
----------------
MAC address assignment is based on stock-firmware. For me, the device
assigns the MAC on the label to Ethernet and the 2.4G WiFi, while the 5G
WiFi has a separate MAC with +2.
*:88 Ethernet/2.4G label, uboot 0x1fc00, userconfig 0x0158
*:89 unused userconfig 0x0160
*:8A 5G not present in flash
This seems to be the first ramips device with a TP-Link v1 header. The
original firmware has the string "EU" embedded, there might be some region-
checking going on during the firmware upgrade process. The original
firmware also contains U-Boot and thus overwrites the boot loader during
upgrade.
In order to flash back to stock, the first header and U-Boot need to be
stripped from the original firmware.
Signed-off-by: Andreas Böhler <dev@aboehler.at>
This harmonizes the line wrapping in image Makefile device
definitions, as those are frequently copy-pasted and are a common
subject of review comments. Having the treatment unifying should
reduce the cases where adjustment is necessary afterwards.
Harmonization is achieved by consistently (read "strictly")
applying certain rules:
- Never put more than 80 characters into one line
- Fill lines up (do not break after 40 chars because of ...)
- Use one tab for indent after wrapping by "\"
- Only break after pipe "|" for IMAGE variables
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
ipTIME A104ns is a 2.4/5GHz band AC750 router, based on MediaTek MT7620A.
Specifications:
- SoC: MT7620A
- RAM: DDR2 64MB
- Flash: SPI NOR 8MB
- WiFi:
- 2.4GHz: SoC internal
- 5GHz: MT7610EN
- Ethernet: 5x 10/100Mbps
- Switch: SoC internal
- USB: 1x 2.0
- UART:
- J2: 3.3V, TX, RX, GND (3.3V is the square pad) / 57600 8N1
Installation via web interface:
1. Flash **initramfs** image through the stock web interface.
2. Boot into OpenWrt and perform sysupgrade with sysupgrade image.
Revert to stock firmware:
1. Perform sysupgrade with stock image.
In contrast to to-be-supported A1004ns, the A104ns has no usable
value in 0x1fc40 (uboot), so wan_mac needs to be calculated.
Also note that GPIOs for the LEDs really are inverted compared to
the A1004ns.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[moved state_default to device DTS, reordered properties in wmac,
added comment about wan_mac and LED GPIOs]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
JCG JHR-AC876M is an AC2600M router
Hardware specs:
SoC: MT7621AT
2.4GHz: MT7615N 4x4 @ PCIe0
5GHz: MT7615N 4x4 @ PCIe1
Flash: Winbond W25Q128JVSQ 16MiB
RAM: Nanya NT5CB128M16 256MiB
USB 2.0 and 3.0 ports
6 LEDs, 3 of which are connected to SoC GPIO
Reset and WPS buttons
Flash instructions:
Stock to OpenWrt:
Upload factory.bin in stock firmware's upgrade page,
do not preserve settings
OpenWrt to stock:
Push and hold the reset button for 5s while power cycling to
enter recovery mode;
Visit 192.168.1.1 and upload stock firmware
MAC addresses map:
0x0004 *:1c wlan2g/wan/label
0x8004 *:20 wlan5g
0xe000 *:1b lan
0xe006 *:1a not used in stock fw
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
This allows JCG_MAXSIZE to be specified in kilobytes. This makes
this value more consistent and easier comparable with other size
variables.
This also changes the only occurence of the variable, for Cudy WR1000.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
ipTIME A6ns-M is a 2.4/5GHz band AC1900 router, based on MediaTek MT7621A.
Specifications:
- SoC: MT7621AT
- RAM: DDR3 128MB
- Flash: SPI NOR 16MB
- WiFi:
- 2.4GHz: MT7615
- 5GHz: MT7615
- Ethernet: 5x 10/100/1000Mbps
- Switch: SoC internal
- UART:
- J4: 3.3V, TX, RX, GND (3.3V is the square pad) / 57600 8N1
Installation via web interface:
1. Flash **initramfs** image through the stock web interface.
2. Boot into OpenWrt and perform sysupgrade with sysupgrade image.
Revert to stock firmware:
1. Perform sysupgrade with stock image.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
ZIO FREEZIO is a 2.4/5GHz band AC1200 router, based on MediaTek MT7621A.
Specifications:
- SoC: MT7621AT
- RAM: DDR3 128MB
- Flash: SPI NOR 16MB
- WiFi:
- 2.4GHz: MT7603EN
- 5GHz: MT7612EN
- Ethernet: 5x 10/100/1000Mbps
- Switch: SoC internal
- USB: 1x 3.0
- UART:
- J4: 3.3V, RX, TX, GND (3.3V is the square pad) / 57600 8N1
Notes:
- FREEZIO has almost the same board as WeVO W2914NS v2.
- Stock firmware is based on OpenWrt BB.
MAC addresses in factory partition:
0x0004: WiFi 2.4GHz (label_mac-8)
0x002e: WAN (label_mac)
0x8004: WiFi 5GHz (label_mac-4)
0xe000: LAN (label_mac+1)
Installation via web interface:
1. Access web admin page and turn on "OpenWrt UI mode".
2. Flash sysupgrade image through LuCI, with the "Keep settings" option
OFF.
Revert to stock firmware:
1. Perform sysupgrade with stock image.
Make sure to NOT preserve settings.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[rebase, use mt7621_wevo_w2914ns-v2.dtsi]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The DTS variable has been removed in 402138d12d ("ramips: Derive
DTS name from device name in Makefile"), but the DEVICE_VARS entry
has been overlooked.
Remove it now since we are not using this variable.
This must _not_ be backported to 19.07, where the variable is still
in use.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The stock firmware and bootloader only accept uImage with names that
match certain patterns. This patch enables OpenWrt installation from
stock firmware without having to reflash the bootloader or access the
UART console.
Installation via web interface:
1. Flash **initramfs** image through the stock web interface.
2. Boot into OpenWrt and perform sysupgrade with sysupgrade image.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
ALFA Network Quad-E4G is a universal Wi-Fi/4G platform, which offers
three miniPCIe (PCIe, USB 2.0, SIM) and a single M.2 B-key (dual-SIM,
USB 3.0) slots, RTC and five Gigabit Ethernet ports with PoE support.
Specification:
- MT7621A (880 MHz)
- 256/512 MB of RAM (DDR3)
- 16/32+ MB of FLASH (SPI NOR)
- optional second SPI flash (8-pin WSON/SOIC)
- 1x microSD (SDXC) flash card reader
- 5x 10/100/100 Mbps Ethernet, with passive PoE support (24 V) in LAN1
- optional 802.3at/af PoE module for WAN
- 3x miniPCIe slot (with PCIe and USB 2.0 buses, micro SIM and 5 V)
- 1x M.2/NGFF B-key 3042 (USB 3.0/2.0, mini + micro SIM)
- RTC (TI BQ32002, I2C bus) with backup battery (CR2032)
- external hardware watchdog (EM Microelectronic EM6324)
- 1x USB 2.0 Type-A
- 1x micro USB Type-B for system serial console (Holtek HT42B534)
- 11x LED (5 for Ethernet, 5 driven by GPIO, 1x power indicator)
- 3x button (reset, user1, user2)
- 1x I2C (4-pin, 2.54 mm pitch) header on PCB
- 4x SIM (6-pin, 2.00 mm pitch) headers on PCB
- 2x UART2/3 (4-pin, 2.54 mm pitch) headers on PCB
- 1x mechanical power switch
- 1x DC jack with lock (24 V)
Other:
- U-Boot selects default SIM slot, based on value of 'default_sim' env
variable: '1' or unset -> SIM1 (mini), '2' -> SIM2 (micro). This board
has additional logic circuit for M.2 SIM switching. The 'sim-select'
will work only if both SIM slots are occupied. Otherwise, always slot
with SIM inside is selected, no matter 'sim-select' value.
- U-Boot enables power in all three miniPCIe and M.2 slots before
loading the kernel
- this board supports 'dual image' feature (controlled by 'dual_image'
U-Boot environment variable)
- all three miniPCIe slots have additional 5 V supply on pins 47 and 49
- the board allows to install up to two oversized miniPCIe cards (vendor
has dedicated MediaTek MT7615N/D cards for this board)
- this board has additional logic circuit controlling PERSTn pins inside
miniPCIe slots. By default, PERSTn (GPIO19) is routed to all miniPCIe
slots but setting GPIO22 to high allows PERSTn control per slot, using
GPIO23-25 (value is inverted)
You can use the 'sysupgrade' image directly in vendor firmware which is
based on OpenWrt (make sure to not preserve settings - use 'sysupgrade
-n -F ...' command). Alternatively, use web recovery mode in U-Boot:
1. Power the device with reset button pressed, the modem LED will start
blinking slowly and after ~3 seconds, when it starts blinking faster,
you can release the button.
2. Setup static IP 192.168.1.2/24 on your PC.
3. Go to 192.168.1.1 in browser and upload 'sysupgrade' image.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
ALFA Network R36M-E4G is a dual-SIM, N300 Wi-Fi, compact size platform
based on MediaTek MT7620A WiSoC. This product is designed for operation
with 4G modem (can be bought in bundle with Quectel EC25, EG25 or EP06)
but supports also Wi-Fi modules (miniPCIe slot has USB and PCIe buses).
Specification:
- MT7620A (580 MHz)
- 64/128/256 MB of RAM (DDR2)
- 16/32+ MB of FLASH (SPI NOR)
- 2x 10/100 Mbps Ethernet, with passive PoE support (24 V)
- 2T2R 2.4 GHz (MT7620A), with ext. LNA (RFFM4227)
- 1x miniPCIe slot (with PCIe and USB 2.0 buses and optional 5 V)
- 2x SIM slot (mini, micro) with detect and switch driven by GPIO
- 2x u.fl antenna connectors (for Wi-Fi)
- 8x LED (7 driven by GPIO)
- 2x button (reset, wifi)
- 2x UART (4-pin/2.54 mm pitch, 10-pin/1.27 mm pitch) headers on PCB
- 1x I2C (4-pin, 1.27 mm pitch) header on PCB
- 1x LED (8-pin, 1.27 mm pitch) header on PCB
- 1x DC jack with lock (12 V)
Other:
- there is a dedicated, 4-pin connector for optional RTC module (Holtek
HT138x) with 'enable' input, not available at the time of preparing
support for this board
- miniPCIe slot supports additional 5 V supply on pins 47 and 49 but a
jumper resistor (R174) is not installed by default
- U-Boot selects default SIM slot, based on value of 'default_sim' env
variable: '1' or unset -> SIM1 (mini), '2' -> SIM2 (micro). This will
work only if both slots are occupied, otherwise U-Boot will always
select slot with SIM card inside (user can override it later, in
user-space)
- U-Boot resets the modem, using PERSTn signal, before starting kernel
- this board supports 'dual image' feature (controlled by 'dual_image'
U-Boot environment variable)
Flash instruction:
You can use the 'sysupgrade' image directly in vendor firmware which is
based on OpenWrt (make sure to not preserve settings - use 'sysupgrade
-n -F ...' command). Alternatively, use web recovery mode in U-Boot:
1. Power the device with reset button pressed, the modem LED will start
blinking slowly and after ~3 seconds, when it starts blinking faster,
you can release the button.
2. Setup static IP 192.168.1.2/24 on your PC.
3. Go to 192.168.1.1 in browser and upload 'sysupgrade' image.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
CY-SWR1100 has a USB LED but kmod-usb-ledtrig-usbport is missing
in default images. This commit adds it.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[changed commit title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Specifications:
* SoC: MT7620A
* RAM: 64 MB DDR
* Flash: 8MB NOR SPI flash
* WiFi: MT7612E (5Ghz) and builtin MT7620A (2.4GHz)
* LAN: 1x100M
The -factory images can be flashed from the
device's web interface or via nmrpflash.
The device seems to use base PCB as EX3700/EX3800,
but supporting AC1200 using MT7612E.
MAC adresses:
5.0 GHz 0x8004 *:9a
2.4 GHz 0x4 *:9b
lan 0x28 *:9b
wan 0x2e *:9c
Since this is a one-port device, although wan MAC address is
set in flash, it is not used in OpenWrt setup.
Signed-off-by: Frederik Noe-Sdun <Frederik.Sdun@googlemail.com>
[rebased, extended commit message, tiny DTS style fixes]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The elecom-header renames the firmware image to v_0.0.0.bin, stores its
MD5 sum as v_0.0.0.md5 and tars both files again.
Both v_0.0.0 files are created as the build user making it harder to
reproduce.
This commit sets the owner/group of both files to root by adding extra
options to the final tar command.
Before:
0 buildbot (101) buildbot (102) 3932164 2019-11-05 14:43:22.000000 v_0.0.0.bin
0 buildbot (101) buildbot (102) 33 2019-11-05 14:43:22.000000 v_0.0.0.md5
After:
0 root (0) root (0) 3932164 2019-11-05 23:43:08.000000 v_0.0.0.bin
0 root (0) root (0) 33 2019-11-05 23:43:08.000000 v_0.0.0.md5
Signed-off-by: Paul Spooren <mail@aparcar.org>
rt3883.mk contains both RT3662 and RT3883 device profiles, but commit
6a104ac772 set MTK_SOC to rt3883 for all devices. This patch fixes it,
and renames dts files accordingly. And SoC compatible strings are also
appended in the dts.
Fixes: 6a104ac772 ("ramips/rt288x,rt3883: Name DTS files based on scheme")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
This commit adds support for the ZBT WE1026-H, an outdoor AP with
support for adding an internal LTE modem. The detailed specs are:
* CPU: MT7620A
* 2x 10/100Mbps Ethernet (LAN port has passive PoE support).
* 16/32 MB Flash.
* 128/256 MB RAM.
* 1x USB 2.0 port.
* 1x mini-PCIe slot (only USB2.0 bus).
* 1x SIM slot (standard size).
* 1x 2.4Ghz WIFI (rt2800).
* 1x button.
* 6x LEDS (4 GPIO-controlled).
* 1x micro-SD reader.
The following have been tested and working:
- Ethernet switch
- Wifi
- Mini-PCIe slot + SIM slot
- USB port
- microSD slot
- sysupgrade
- reset button
Installation and recovery:
In order to install OpenWRT the first time or ito recover the router,
you can use the web-based recovery system. Keep the reset button pressed
during boot and access 192.168.1.1 in your browser when your machine
obtains an IP address. Upload the firmware to start the recovery
process.
Notes:
* When binding the USB LED to a usbport, the LED is switched on all the
time due to the presence of an internal hub. Thus, it does not really
signal any USB-information.
* I only have the 32MB version and have only added support for this
device. However, the files are structured so that adding support for the
16MB version should be easy.
* Only the LAN port is accessible from the outside of the casing and LEDs
are not visible.
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
[rebased onto base-files split, minor style fixes, removed use of
USB led as power LED]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This patch renames and reassembles the common definition for
Netgear R6xxx devices in mt7621.mk. The following goals should be
achieved:
- Give the node a more generic name instead of adding devices to it
- Use the common definition in the (less) similar R6220 node
- Include/exclude settings into the common definition so the common
node contains the common definitions
- Prepare for support of R6700 v2
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
- CMIIT ID: 2019AP2581
- SoC: MediaTek MT7621
- Flash: 16MiB NOR SPI (GigaDevice GD25Q128B)
- RAM: 128MiB DDR3 (ESMT M15T1G1664A)
- Serial: As marked on PCB, 3V3 logic, baudrate is 115200, 8n1
- Ethernet: 3x 10/100/1000 Mbps (switched, 2xLAN + WAN)
- WIFI0: MT7603E 2.4GHz 802.11b/g/n
- WIFI1: MT7612E 5GHz 802.11ac
- Antennas: 4x external (2 per radio), non-detachable
- LEDs: Programmable "power" LED (two-coloured, yellow/blue)
Non-programmable "internet" LED (shows WAN activity)
- Buttons: Reset
INSTALLATION:
Bootloader won't accept any serial input unless "boot_wait" u-boot
environment variable is changed to "on". Vendor firmware (looks like
an illegal OpenWrt fork) won't accept any serial input unless
"uart_en" is set to "1". Tricks to force u-boot to use default
environment do not help as it's restricted in the same way.
With bootloader unlocked the easiest way would be to TFTP the
sysupgrade image or to sysupgrade after loading an initramfs one.
For porting the flash contents were changed externally with an SPI
programmer (after lifting Vcc flash IC pin away from the PCB).
Forum thread [0] indicates that this device is identical to "Xiaomi Mi
Router 4A Gigabit Edition".
[0] https://forum.openwrt.org/t/xiaomi-mi-router-4a-gigabit-edition-r4ag-r4a-gigabit-fully-supported-but-requires-overwriting-spi-flash-with-programmer/36685
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
The Asus RT-AC65P router is identical with the RT-AC85P, but better to make separate images for it.
On both routers the installation can be done also via SSH:
Note: The user/password for SSH is identical with the one used in the
Web-interface.
1. Complete the initial setup wizard.
2. Activate SSH under "Administration" -> "System".
3. Transfer the OpenWrt factory image via scp:
> scp openwrt-ramips-mt7621-asus_rt-ac65p-squashfs-factory.bin admin@192.168.50.1:/tmp
4. Connect via SSH to the router.
> ssh admin@192.168.50.1
5. Write the OpenWrt image to flash.
> mtd-write -i
/tmp/openwrt-ramips-mt7621-asus_rt-ac65p-squashfs-factory.bin -d linux
6. Reboot the router
> reboot
Changelog:
v3: removed [] from filename, rebased to latest master
v2: Rebased to latest master
v1: Initial release
Signed-off-by: Gabor Varga <vargagab@gmail.com>
Device node names were updated, but updating TARGET_DEVICES
was overlooked.
Fixes: 4408723d42 ("ramips: remove RAM size from device name
for UniElec devices")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
UniElec devices are the last ones in ramips target still having
the RAM size in device name although RAM size is auto-detected.
Remove this from device name, compatible, etc., as it's not
required and might be misleading to users and developers adding
device support copying those devices.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The Phicomm KE 2P is identical to the already supported Phicomm K2P,
renamed for the European market. Use the ALT0 buildroot tags to show
both devices.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
This removes _all_ occurrences of kmod-usb-core from
DEVICE_PACKAGES and similar variables.
This package is pulled as dependency by one of the following
packages in any case:
- kmod-usb-chipidea
- kmod-usb-dwc2
- kmod-usb-ledtrig-usbport
- kmod-usb-ohci
- kmod-usb2
- kmod-usb2-pci
- kmod-usb3
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
[remove kmod-usb-core from EnGenius ESR600]
Signed-off-by: David Bauer <mail@david-bauer.net>
All Zbtlink ramips devices except the ZBT-WE1026-5G include the
zbt-/ZBT- prefix in their model name.
This changes ZBT-WE1026-5G to also follow that scheme.
The patch moves some block to keep alphatical order.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Spelling of Zbtlink varies across image definitions and DTS files.
This patch uses Zbtlink consistently and also updates the model
in DTS files to contain the vendor in all cases.
This patch is cosmetical, as there should be no dependencies on
device model name in ramips anymore.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
I-O DATA WNPR2600G has an "elx-header", so move this definition to
generic makefile to use it from mt7621 subtarget.
This definition is also added to mt7621.mk in
f285e8634c, so remove it from mt7621.mk.
And added a line to cleanup used header file.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
ipTIME A3 is a 2.4/5GHz band AC1200 router, based on MediaTek
MT7628AN.
Specifications:
- SoC: MT7628AN
- RAM: DDR2 64MB
- Flash: SPI NOR 8MB
- WiFi:
- 2.4GHz: SoC internal
- 5GHz: MT7612EN
- Ethernet: 3x 10/100Mbps
- Switch: SoC internal
- UART:
- J1: 3.3V, TX, RX, GND (3.3V is the square pad) / 57600 8N1
Installation via web interface:
1. Flash **initramfs** image through the stock web interface.
2. Boot into OpenWrt and perform sysupgrade with sysupgrade image.
Revert to stock firmware:
1. Perform sysupgrade with stock image.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Hardware:
SoC: MT7621A
Flash: 32 MiB
RAM: 512 MiB
Ethernet: built-in switch
USB: 1x USB3.0
SATA: ASM1060, 1 SATA port
Flash instruction (TFTP):
1. Set PC to fixed ip address 192.168.173.22
2. Download *-sysupgrade.bin image and rename it to firmware.img
3. Start a tftp server with the image file in its root directory
4. Turn off the router
5. Turn on router,press the reset button and wait ~15 seconds
6. Release the reset button and after a short time
the firmware should be transferred from the tftp server
7. Wait ~3 minutes to complete recovery.
Signed-off-by: Qi Jiang <rushx@live.cn>
[squash commits, add label-mac-device, fix sign-off style]
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
The EnGenius ESR600 is a dual band wireless router with a 4-port gigabit
Ethernet switch, a gigabit Ethernet WAN port and a USB port.
Specification:
- Bootloader: U-Boot
- SoC: MediaTek MT7620A (600 MHz)
- Flash: 16MB, Macronix MX25L12845E
- RAM: 64MB, Nanya NT5TU32M16DG-AC
- Serial: 115200 baud, no header, 3.3V
J2: Vcc (arrow), Gnd, Tx, Rx
- USB: USB 2, 5V
- Ethernet: 5 x 1 Gb/s 4 LAN 1 WAN, Atheros AR8327
- WiFi0: 5 GHz 802.11 b/g/n Ralink RT5592N
300 Mb/s, 2T2R
- WiFi1: 2.4 GHz 802.11 b/g/n integrated
300 Mb/s, 2T2R
- Antennas: 2 per radio, internal
- LEDs: 1 programmable power (amber)
2 programable radio (blue)
1 programable WPS-5G (blue)
1 non-programable WAN activity (blue)
1 unconfigured WPS-2.4G (amber)
- Buttons: GPIO: Reset, WPS
Installation:
Use the OEM web interface to install the ...-factory.dlf image.
Use the OpenWRT ...-sysupgrade.bin image for future upgrades.
The J2 serial port can be accessed either by soldering in a header,
standard 0.1" spacing, or by using pogo-pins against the back side.
As configured by the OEM, the U-Boot boot delay is short, however quickly
typing "1" leads to the U-Boot "System load Linux to SDRAM via TFTP"
prompt. The TFTP client is configured by default with
client: 192.168.99.9
server: 192.168.99.8
filename: uImageESR600
It will load an OpenWRT initramfs kernel with this method.
Known issues:
1) Only the ports externally labeled WAN, LAN3 and LAN4 are operational.
LAN1 and LAN2 do not appear to power up. This issue is also present
in the Lava LR25G001.
2) The amber WPS-2.4G LED, in the same lightguide as the blue WPS-5G LED,
is not configured in the Device Tree specification.
3) The blue WAN activity LED is not configured in the Device Tree
specification as this causes the AR8327 switch to fail to initialize.
Signed-off-by: Nick Briggs <nicholas.h.briggs@gmail.com>
[merge conflict in 02_network]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
SoC: Mediatek MT7621A
CPU: 4x 880Mhz
Cache: 32 KB I-Cache and 32 KB D-Cach
256 KB L2 Cache (shared by Dual-Core)
RAM: DDR3 512MB 16bits BUS
FLASH: 16MB
Switch: Mediatek Gigabit Switch (2 x LAN, 1 x WAN)
POE: (1x PD, 2x PSE)
USB: 1x 3.0
PCI: 3x Mini PCIe (3 USB2.0 + 2 x UIM interface)
GPS: Quectel L70B
SIM: 2 Slots
BTN: Reset
LED: - Power
- Ethernet
- Wifi
- USB
UART: UART is present as Pads with throughholes on the PCB.
They are located on left side.
3.3V - RX - GND - TX / 57600-8N1
3.3V is the square pad
Installation
------------
The stock image is a modified openwrt and can be overflashed via sysupgrade -F
Signed-off-by: Daniel Danzberger <daniel@dd-wrt.com>
[merge conflict in mt7621.mk]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
SoC: MediaTek MT7621AT dual-core @ 880MHz
RAM: 256M (Winbond W632GG6KB-1)
FLASH: 128MB (Macronix MX30LF1G18AC-TI)
WiFi: - 2.4GHz MediaTek MT7615N bgn
- 5GHz MediaTek MT7615N nac
Switch: SoC integrated Gigabit Switch (4 x LAN, 1 x WAN)
USB: 1 x USB 3.1 (Gen 1)
BTN: Reset, WPS
LED: - Power (blue)
- 5Ghz (blue)
- 2.4GHz (blue)
- Internet (blue)
- 4x LAN (blue)
(LAN/WAN leds are not controllable by GPIOs)
UART: UART is present as Pads marked J4 on the PCB.
3.3V - TX - RX - GND / 57600-8N1
3.3V is the square pad
MAC: The MAC address on the router-label matches the MAC of
the 2.4 GHz WiFi.
LAN and WAN MAC are identical: MAC_LABEL+4
5 GHz WiFi MAC: also MAC_LABEL+4
Installation
------------
Via U-Boot tftpd:
Switch on device, within 2s press reset button and keep pressed
until power LED starts blinking slowly.
Upload factory image via tftp put, the router's ip is 192.168.1.1
and expects the client on 192.168.1.75.
The images also work on the Asus RT-AC65P models as tested by Gabor.
Signed-off-by: Birger Koblitz <mail@birger-koblitz.de>
Tested-by: Gabor Varga <vargagab@gmail.com>
[fixed Asus -> ASUS in DTS]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
SoC: MediaTek MT7621AT dual-core @ 880MHz
RAM: 256M (Nanya NT5CC128M)
FLASH: 16MB (Macronix MX25L12835F)
WiFi: - 2.4GHz MediaTek MT7615N bgn
- 5GHz MediaTek MT7615N nac
Switch: SoC integrated Gigabit Switch (4 x LAN, 1 x WAN)
USB: No
BTN: Reset, WPS
LED: 4 red LEDs, indistinguishable when casing closed
UART: UART is present as Pads marked J1 on the PCB.
3.3V - RX - GND - TX / 57600-8N1
3.3V is the square pad
Installation
------------
Update the factory image via the OEM web-interface
(by default:http://192.168.1.1)
The sysupgrade image can be installed via TFTP from
the U-Boot bootloader. Connect ethernet port 2.
Signed-off-by: Birger Koblitz <mail@birger-koblitz.de>
[flash node rename, EDIMAX -> Edimax, complete device model name]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
The Linkit Smart 7688 has a SD-Card reader that does not work with the official build of openwrt. Adding kmod-sdhci-mt7620 makes it working.
Signed-off-by: Ivan Hörler <i.hoerler@me.com>
This patch does the following things:
1. mark u-boot-env writable
2. add bootcount support
Currently, u-boot has a flag_boot_success env variable to reset.
Also reset it in our firmware to follow the behavior in vendor's
firmware.
3. disable usb support
This router doesn't have usb port at all.
4. increase spi clock to 40MHz
5. fix pinmux groups
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
As Netgear uses the same image for R6260, R6350 & R6850
we can merge device tree files and generate separate
images for each device.
Signed-off-by: Christoph Krapp <achterin@googlemail.com>
[add missing WiFi compatible string, fix network
configuration]
Signed-off-by: David Bauer <mail@david-bauer.net>
This adds factory image generation for all three
devices. These images can be flashed via WebUI
for easy installation.
Thanks to David Bauer for the inspiration.
Signed-off-by: Christoph Krapp <achterin@googlemail.com>
[altered commit to only include the R6350]
Signed-off-by: David Bauer <mail@david-bauer.net>
This adds an easy-installation factory image for the NETGEAR R6220
router. The factory image can either be flashed via the vendor Web-UI or
the bootloader using nmrpflash.
Tested with NETGEAR V1.1.0.86 firmware.
Signed-off-by: David Bauer <mail@david-bauer.net>
These devices are sold as a "NAS HDD Enclousure"
and have a "NAS Media Streaming & File Server & AP" on
the box. That's why I think they should have some support
for the HDD right out-of-the-box.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
SoC: MT7621AT
RAM: 256MB
Flash: 16M SPI
Ethernet: 5x GE ports
WiFi: 2.4G: MT7615N
5G: MT7615N
Flash instruction:
1.Modify the file to linux.bin
2.Set up FTP service
3.Computer settings fixed IP: 192.168.179.50 255.255.255.0
4.Turn on the power and press and hold the reset button until the indicator light is on for about 5 seconds.
Signed-off-by: Zhenjian Zhang <itdesk.zhang@gmail.com>
[fix mac location]
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
ipTIME A604M is a 2.4/5GHz band AC1200 router, based on MediaTek
MT7628AN.
Specifications:
- SoC: MT7628AN
- RAM: DDR2 64MB
- Flash: SPI NOR 8MB
- WiFi:
- 2.4GHz: SoC internal
- 5GHz: MT7612EN
- Ethernet: 5x 10/100Mbps
- Switch: SoC internal
- UART:
- J1: 3.3V, TX, RX, GND (3.3V is the square pad) / 57600 8N1
Installation via web interface:
1. Flash **initramfs** image through the stock web interface.
2. Boot into OpenWrt and perform sysupgrade with sysupgrade image.
Revert to stock firmware:
1. Perform sysupgrade with stock image.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Revert "mac80211: add new minstrel_ht patches to improve probing on mt76x2" (9861050b85)
Revert "kernel: use bulk free in kfree_skb_list to improve performance" (98b654de2e)
Revert "ramips: add preliminary support for WIO ONE" (085141dc5b)
Revert "ramips: add preliminary support for SGE AP-MTKH7-0006 developer board" (b1db6d0539)
Revert "build: use config.site generated by autoconf-lean, drop hardcoded sitefiles" (363ce4329d)
Revert "toolchain: add autoconf-lean" (fdb30eed03)
Revert "build: allow overriding the filename on the remote server when downloading" (6fa0e07758)
Signed-off-by: Felix Fietkau <nbd@nbd.name>
HiWiFi HC5761A is an "MT7628AN variant" of HC5761
Specifications:
- MediaTek MT7628AN 580MHz
- 128 MB DDR2 RAM
- 16 MB SPI Flash
- 2.4G MT7628AN 802.11bgn 2T2R 300Mbps
- 5G MT7610EN 802.11ac 433Mbps
- 3x 10/100 Mbps Ethernet
Flash instruction:
1. Get SSH access to the router
2. SSH to router with `ssh -p 1022 root@192.168.199.1`, The SSH password is the same as the webconfig one
3. Upload OpenWrt sysupgrade firmware into the router's `/tmp` folder with SCP
4. Run `mtd write /tmp/<filename> firmware`
5. reboot
Known bug:
- SD slot does not work (See PR 1500)
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
This cosmetical patch is just meant to make comparing/checking
IMAGE_SIZE values easier.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
There are frequent examples of the ralink_default_fw_size_xxx
variables being used to "roughly" set flash size without caring
about the actual size of the firmware partition.
To discourage this behavior, this patch removes the variables and
just sets IMAGE_SIZE by its numeric value for each target.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Currently, ramips target defines 0x7b0000 as default IMAGE_SIZE
for all devices in ramips target, i.e. this will be set if a
device does not specify IMAGE_SIZE itself.
From 92 devices using that default due to a "missing" IMAGE_SIZE,
14 were incorrect by a small amount (i.e. still "8M" flash) and
12 were completely off ("16M", "4M", ...).
This patch thus removes the _default_ IMAGE_SIZE and defines
IMAGE_SIZE for each device individually. This should indicate to
people supporting new devices that this parameter has to be cared
about.
For the present code, this patch is cosmetical.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This fixes IMAGE_SIZE for all devices based on the partition size
given in DTS:
DEVICE *.MK *.DTS VERDICT
airlink101_ar670w (4M) 0x3c0000 wrong
airlink101_ar725w - 0x3B0000 wrong
asus_rt-n15 (4M) 0x3b0000
belkin_f5d8235-v1 7744k 0x7b0000 wrong
buffalo_wli-tx4-ag300n (4M) 0x3b0000
buffalo_wzr-agl300nh (4M) 0x3b0000
dlink_dap-1522-a1 3801088 0x3a0000
ralink_v11st-fe (4M) 0x003b0000
asus_rt-n56u - 0x007b0000 default
belkin_f9k1109v1 7224k 0x7a0000 wrong
dlink_dir-645 - 0x7b0000 default
edimax_br-6475nd 7744k 0x00790000
loewe_wmdr-143n - 0x7b0000 default
omnima_hpm 16064k 0x00fb0000
samsung_cy-swr1100 - 0x7b0000 default
sitecom_wlr-6000 7244k 0x713000
trendnet_tew-691gr - 0x007b0000 default
trendnet_tew-692gr - 0x007b0000 default
No verdict means that the device is correctly set.
Legend:
( ): Value is set via ralink_default_fw_size_xxM
[ ]: Value is derived from parent definition
- : Value is not set and derived from default definition
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
In ramips, there are the following predefined values for IMAGE_SIZE
ralink_default_fw_size_4M 3866624 3776k 0x3B0000
ralink_default_fw_size_8M 8060928 7872k 0x7B0000
ralink_default_fw_size_16M 16121856 15744k 0xF60000
ralink_default_fw_size_32M 33226752 32448k 0x1FB0000
Out of those, the "16M" value is obviously odd, as it provides more
room for the remaining partitions than the tree others.
Of the devices in all subtargets, there are actually > 50 that have
a firmware partition with 0xFB0000 size, while only 5 (!) have
0xF60000. From the former, many are set to
ralink_default_fw_size_16M anyway, although it is wrong at the
present point.
Consequently, it makes sense to change ralink_default_fw_size_16M
to 0xFB0000, and to update IMAGE_SIZE for the 5 devices with
0xF60000.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Now that the mt76 driver supports the MT7615D chip found on these
devices, use it.
Also add the wpad-basic package.
Note: the driver supports operation on both the 2.4 GHz and the
5 GHz bands, but not yet concurrently.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Newifi D1 is shipped with an 8GB microSD card in its SD slot
Without SD driver users would not be able to use it unless manually installed
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
TP-Link RE650 v1 is a dual-band AC2600 range extender,
based on MediaTek MT7621A and MT7615E. According to the
wikidevi entry for RE650 this device is identical with
TP-Link RE500 as hardware. This patch supports only RE650.
Hardware specification:
- SoC 880 MHz - MediaTek MT7621AT
- 128 MB of DDR3 RAM
- 16 MB - Winbond 25Q128FVSG
- 4T4R 2.4 GHz - MediaTek MT7615E
- 4T4R 5 GHz - MediaTek MT7615E
- 1x 1 Gbps Ethernet - MT7621AT integrated
- 7x LEDs (Power, 2G, 5G, WPS(x2), Lan(x2))
- 4x buttons (Reset, Power, WPS, LED)
- UART header (J1) - 2:GND, 3:RX, 4:TX
Serial console @ 57600,8n1
Flash instructions:
Upload
openwrt-ramips-mt7621-tplink_re650-v1-squashfs-factory.bin
from the RE650 web interface.
TFTP recovery to stock firmware:
Unfortunately, I can't find an easy way to recover the RE
without opening the device and using modified binaries. The
TFTP upload will only work if selected from u-boot, which
means you have to open the device and attach to the serial
console. The TFTP update procedure does *not* accept the
published vendor firmware binaries. However, it allows to
flash kernel + rootfs binaries, and this works if you have
a backup of the original contents of the flash. It's probably
possible to create special image out of the vendor binaries
and use that as recovery image.
Signed-off-by: Georgi Vlaev <georgi.vlaev@gmail.com>
[re-added variables for kernel header]
Signed-off-by: David Bauer <mail@david-bauer.net>
ELECOM WRC-1167GHBK2-S has a MediaTek MT7615D chip for 2.4/5 GHz
wireless.
A driver package for MT7615 chip is added to OpenWrt in
a0e5ca4f35,
so add preliminary MT7615 chip support for WRC-1167GHBK2-S.
Note: Currently, DBDC mode for MT7615 is not supported in mt76 driver.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
SoC: MediaTek MT7621AT
RAM: 128M (Winbond W631GG6KB-15)
FLASH: 16MB (Spansion S25FL128SA)
WiFi: MediaTek MT7603EN bgn 2SS
WiFi: MediaTek MT7612EN nac 2SS
BTN: Reset - WPS
LED: - Power
- LAN {1-4}
- WAN
- WiFi 2.4 GHz
- WiFi 5 GHz
- USB
UART: UART is present next to the Power LED.
TX - RX - GND - 3V3 / 57600-8N1
3V3 is the nearest one to the Power LED.
Installation
------------
Via TFTP:
1. Set your computers IP-Address to 192.168.1.75.
2. Power up the Router with the Reset button pressed.
3. Release the Reset button after 5 seconds.
4. Upload OpenWRT sysupgrade image via TFTP:
> tftp -4 -v -m binary 192.168.1.1 -c put <IMAGE>
Via SSH:
Note: User/password for SSH is identical with the one used in the
Web-interface.
1. Complete the initial setup wizard.
2. Activate SSH under "Administration" -> "System".
3. Transfer the OpenWrt sysupgrade image via scp:
> scp owrt.bin admin@192.168.1.1:/tmp
4. Connect via SSH to the router.
> ssh admin@192.168.1.1
5. Write the OpenWrt image to flash.
> mtd-write -i /tmp/owrt.bin -d linux
6. Reboot the router
> reboot
Signed-off-by: David Bauer <mail@david-bauer.net>
Belkin F7C027 is clearly Rt5350 SoC, as shown on internal
photographs filed for FCC approval[1].
[1]: https://fcc.io/K7S/F7C027
Fixes commit 3b0264eddb
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This patch applies sorting to the definitions as whole blocks.
Sorting has been performed fully automatic, line count differences
originate from double empty lines removed.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
As introduced with ath79, DTS files for ramips will now be labelled
soc_vendor_device.dts(i). With this change, DTS files can be
selected automatically without further manual links.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
As introduced with ath79, DTS files for ramips will now be labelled
soc_vendor_device.dts(i). With this change, DTS files can be
selected automatically without further manual links.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This will automatically derive the DTS name as in ath79 and thus
makes specifying DTS for every device obsolete.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
---
This patch only introduces the mechanism and is then followed by
commits with renames and Makefile adjustments per subtarget.
Eventually, those can be all squashed into a single commit or left
as they are to enhance overview.
This will "rename" devices in Makefiles to the pattern used in
DTS compatible. This will systematize naming of devices
enormously.
As device names are used to for default SUPPORTED_DEVICES entries,
we need to adjust the source for /tmp/sysinfo/board_name, too.
So remove relevant entries from base-files/lib/ramips.sh and
use device compatible for that.
Despite that, base-files are updated, too.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Include "Archer" in compatible as it is part of the device name.
Update Makefile device names where necessary to match compatible.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Upstream kernel added support for RAW_APPENDED_DTB on ralink arch
in the following commit:
02564fc89d3d ("ralink: Introduce fw_passed_dtb to arch/mips/ralink")
Use upstream solution and get rid of our OWRTDTB hack.
This commit set DEVICE_DTS to $$(DTS) instead of replacing DTS with
DEVICE_DTS in device profile because DTS variable will be dropped
in later commits.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
[Tested on mt7621/mt76x8]
Tested-by: Chuanhong Guo <gch981213@gmail.com>
[Tested on rt305x/mt7620]
Tested-by: INAGAKI Hiroshi <musashino.open@gmail.com>
TP-Link TL-WR841n v14 is a router based on MediaTek MT7628N.
- MediaTek MT7628NN
- 32 MB of RAM
- 4 MB of FLASH
- 2T2R 2.4 GHz
- 5x 10/100 Mbps Ethernet
Installation:
- copy the
'openwrt-ramips-mt76x8-tl-wr841n-v14-squashfs-tftp-recovery.bin'
file to your tftp server root and rename it to 'tp_recovery.bin'.
- configure your PC running the TFTP server with the static IP address
192.168.0.66/24
- push the reset button and plug in the power connector. Wait until
the orange led starts blinking (~6sec)
Signed-off-by: Alexander Müller <donothingloop@gmail.com>
Signed-off-by: Alexander Couzens <lynxis@fe80.eu> [small modifications gpio-hog]
Hardware specs:
SoC: Mediatek MT7621A
CPU: 4x 880Mhz
Cache: 32 KB I-Cache and 32 KB D-Cach
256 KB L2 Cache (shared by Dual-Core)
RAM: DDR3 512MB 16bits BUS
FLASH: 16MB
Switch: Mediatek Gigabit Switch (1 x LAN, 1 x WAN)
USB: 1x 3.0
PCI: 3x Mini PCIe
GPS: Quectel L70B
BTN: Reset
LED: - Power
- Ethernet
- Wifi
- USB
UART: UART is present as Pads with throughholes on the PCB.
They are located on left side.
3.3V - RX - GND - TX / 57600-8N1
3.3V is the square pad
Installation:
The stock image is a modified openwrt and can be overflashed via
# sysupgrade -F image.bin
Signed-off-by: Daniel Danzberger <daniel@dd-wrt.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[removed unused label, formatting]
SoC: MediaTek MT7620a @ 580MHz
RAM: 64M (Winbond W9751G6KB-25)
FLASH: 8MB (Macronix)
WiFi: SoC-integrated: MediaTek MT7620a bgn
WiFi: MediaTek MT7612EN nac
Switch: Mediatek MT7530W Gigabit Switch (4 x LAN, 1 x WAN)
USB: Yes 1 x 2.0 (+ 1 x 2.0 unpopulated header)
BTN: Reset/WPS
LED: - Power (white)
- Internet (blue)
- Wifi (blue)
- USB (blue)
UART: UART is present as Pads with throughholes on the PCB. They are
located in the lower right corner (GbE ports facing up)
3.3V - RX - GND - TX / 57600-8N1
3.3V is the square pad
Installation
------------
Update the factory image via the web-interfaces (by default:
http://edimax.setup)
Signed-off-by: Birger Koblitz <mail@birger-koblitz.de>
[merge conflicts in 01_leds and mt7620.mk, dts whitespace issues]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
SoC: MediaTek MT7620a @ 580MHz
RAM: 64M (Winbond W9751G6KB-25)
FLASH: 8MB (Macronix)
WiFi: SoC-integrated: MediaTek MT7620a bgn
WiFi: MediaTek MT7612EN nac
GbE: 1x (RTL8211E)
BTN: WPS - RFKILL/RF 50%/RF 100% toggle
LED: - Wifi 5g (blue)
- Wifi 2g (blue)
- Crossband (green)
- Power (green)
- WPS (green)
- LAN (Green)
UART: UART is present as Pads with throughholes on the PCB. They are
located next to the switch for the wifi configuration
3.3V - RX - GND - TX / 57600-8N1
3.3V is the square pad
Installation
------------
Update the factory image via the web-interfaces (by default:
192.168.9.2/24).
http://192.168.9.2/index.asp
ramips: add Edimax EW-7478AC
SoC: MediaTek MT7620a @ 580MHz
RAM: 64M (Winbond W9751G6KB-25)
FLASH: 8MB (Macronix)
WiFi: SoC-integrated: MediaTek MT7620a bgn
WiFi: MediaTek MT7612EN nac
GbE: 1x (RTL8211E)
BTN: WPS - RFKILL/RF 50%/RF 100% toggle
LED: - Wifi 5g (blue)
- Wifi 2g (blue)
- Crossband (green)
- Power (green)
- WPS (green)
- LAN (Green)
UART: UART is present as Pads with throughholes on the PCB. They are
located next to the switch for the wifi configuration
3.3V - RX - GND - TX / 57600-8N1
3.3V is the square pad
Installation
------------
Update the factory image via the web-interfaces (by default:
http://edimaxext.setup)
Or push wpa button on power on and send firmware via tftp to 192.168.1.6
The EW-7478AC is identical to the EW-7476RPC, except instead of 2 internal
antennas it has 2 external ones.
Signed-off-by: Birger Koblitz <mail@birger-koblitz.de>
[merge conflict in 01_leds]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
ASUS RP-N53 and Buffalo WHR-600D use RT5592 for 5GHz wireless
After commit 367813b9b1 the driver for RT5592 (rt2800pci)
is not selected by default anymore, which broke their 5GHz wireless
Add it back to device packages
Fixes: 367813b9b1 ("ramips: mt7620: fix dependencies")
Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
Specifications:
- SoC: MT7628DAN (MT7628AN with 64MB built-in RAM)
- Flash: 8M SPI NOR
- Ethernet: 5x 10/100Mbps
- WiFi: 2.4G: MT7628 built-in
5G: MT7612E
- 1x miniPCIe slot for LTE modem (only USB pins connected)
- 1x SIM slot
Flash instruction:
U-boot has a builtin web recovery page:
1. Hold the reset button while powering it up
2. Connect to the ethernet and set an IP in 192.168.1.0/24 range
3. Open your browser and upload firmware through http://192.168.1.1
Note about the LTE modem:
If your router comes with an EC25 module and it doesn't show up
as a QMI device, you should do the following to switch it to QMI
mode:
1. Install kmod-usb-serial-option and a terminal software
(e.g. minicom or screen). All 4 serial ports of the modem
should be available now.
2. Open /dev/ttyUSB3 with the terminal software and type this
AT command: AT+QCFG="usbnet",0
3. Power-cycle the router. You should now get a QMI device
recognized.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
The R6220 and WNDR3700v5 are identical apart from using NAND/NOR flash and
having a different casing. This adds a new cleaned up R6220.dtsi with the
common bits for both devices. Both devices now have feature parity.
Performed cleanup:
* generic DTS node names
* regulator for usb power
* added missing pinctrl groups
* use switch port instead of VLAN as trigger for WAN LED
Fixes for WNDR3700v5:
* all LEDS work
* correct ethernet MAC addresses
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
- SoC: MediaTek MT7628AN
- Flash: 16MB (Winbond W25Q128JV)
- RAM: 64MB
- Serial: As marked on PCB, 3V3 logic, baudrate is 115200
- Ethernet: 3x 10/100 Mbps (switched, 2x LAN + WAN)
- WIFI0: MT7628AN 2.4GHz 802.11b/g/n
- WIFI1: MT7612EN 5GHz 802.11ac
- Antennas: 4x external (2 per radio), non-detachable
- LEDs: Programmable power-LED (two-colored, yellow/blue)
Non-programmable internet-LED (shows WAN-activity)
- Buttons: Reset
INSTALLATION:
1. Connect to the serial port of the router and power it up.
If you get a prompt asking for boot-mode, go to step 3.
2. Unplug the router after
> Erasing SPI Flash...
> raspi_erase: offs:20000 len:10000
occurs on the serial port. Plug the router back in.
3. At the prompt select option 2 (Load system code then
write to Flash via TFTP.)
4. Enter 192.168.1.1 as the device IP and 192.168.1.2 as the
Server-IP.
5. Connect your computer to LAN1 and assign it as 192.168.1.2/24.
6. Rename the sysupgrade image to test.bin and serve it via TFTP.
7. Enter test.bin on the serial console and press enter.
Signed-off-by: Markus Scheck <markus@mscheck.de>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[added mt76 compatible]
Cudy WR1200 is an AC1200 AP with 3-port FE and 2 non-detachable antennas
Specifications:
MT7628 (580 MHz)
64 MB of RAM (DDR2)
8 MB of FLASH
2T2R 2.4 GHz (MT7628)
2T2R 5 GHz (MT7612E)
3x 10/100 Mbps Ethernet (2 LAN + 1 WAN)
2x external, non-detachable antennas (5dbi)
UART header on PCB (57600 8n1)
7x LED, 2x button
Known issues:
The Power LED is always ON, probably because it is connected
directly to power.
Flash instructions
------------------
Load the ...-factory.bin image via the stock web interface.
Openwrt upgrade instructions
----------------------------
Use the ...-sysupgrade.bin image for future upgrades.
Revert to stock FW
------------------
Warning! This tutorial will work only with the following OEM FW:
WR1000_EU_92.122.2.4987.201806261618.bin
WR1000_US_92.122.2.4987.201806261609.bin
If in the future these firmwares will not be available anymore,
you have to find the new XOR key.
1) Download the original FW from the Cudy website.
(For example WR1000_EU_92.122.2.4987.201806261618.bin)
2) Remove the header.
dd if="WR1000_EU_92.122.2.4987.201806261618.bin" of="WR1000_EU_92.122.2.4987.201806261618.bin.mod" skip=8 bs=64
3) XOR the new file with the region key.
FOR EU: 7B76741E67594351555042461D625F4545514B1B03050208000603020803000D
FOR US: 7B76741E675943555D5442461D625F454555431F03050208000603060007010C
You can use OpenWrt's tools/firmware-utils/src/xorimage.c tool for this:
xorimage -i WR1000..bin.mod -o stock-firmware.bin -x -p 7B767..
Or, you can use this tool (CHANGE THE XOR KEY ACCORDINGLY!):
https://gchq.github.io/CyberChef/#recipe=XOR(%7B'option':'Hex','string':''%7D,'',false)
4) Check the resulting decrypted image.
Check if bytes from 0x20 to 0x3f are:
4C 69 6E 75 78 20 4B 65 72 6E 65 6C 20 49 6D 61 67 65 00 00 00 00 00 00 00 00 00 00 00 00 00 00
Alternatively, you can use u-boot's tool dumpimage tool to check
if the decryption was successful. It should look like:
# dumpimage -l stock-firmware.bin
Image Name: Linux Kernel Image
Created: Tue Jun 26 10:24:54 2018
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 4406635 Bytes = 4303.35 KiB = 4.20 MiB
Load Address: 80000000
Entry Point: 8000c150
5) Flash it via forced firmware upgrade and don't "Keep Settings"
CLI: sysupgrade -F -n stock-firmware.bin
LuCI: make sure to click on the "Keep settings" checkbox
to disable it. You'll need to do this !TWICE! because
on the first try, LuCI will refuse the image and reset
the "Keep settings" to enable. However a new
"Force upgrade" checkbox will appear as well.
Make sure to do this very carefully!
Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[added wifi compatible, spiffed-up the returned to stock instructions]
This uses the existing rules for Sercomm factory images and moves them
to the ramips image Makefile, so they can be used in all subtargets.
The new factory image for WNDR3700v5 can be flashed using nmrpflash.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Specification:
CPU: MT7628 580 MHz. MIPS 24K
RAM: 128 MB
Flash: 32 MB
WIFI: 802.11n/g/b 20/40 MHz
Ethernet: 5 Port ethernet switch
UART: 2x
Flash instruction:
The U-boot is based on Ralink SDK so we can flash the firmware using UART:
1. Configure PC with a static IP address and setup an TFTP server.
2. Put the firmware into the tftp directory.
3. Connect the UART0 line as described on the PCB.
4. Power up the device and press 2, follow the instruction to
set device and tftp server IP address and input the firmware
file name. U-boot will then load the firmware and write it into
the flash.
5. After firmware is started connect via ethernet at 192.168.1.1
Signed-off-by: Liu Yu <f78fk@live.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [removed dupped subject]
ZBT WE826-E is a dual-SIM version of the ZBT WE826. The router has the
following specifications:
- MT7620A (580 MHz)
- 128MB RAM
- 32MB of flash (SPI NOR)
- 5x 10/100Mbps Ethernet (MT7620A built-in switch)
- 1x microSD slot
- 1x miniPCIe slot (only USB2.0 bus)
- 2x SIM card slots (standard size)
- 1x USB2.0 port
- 1x 2.4GHz wifi (rt2800)
- 10x LEDs (4 GPIO-controlled)
- 1x reset button
The following have been tested and working:
- Ethernet switch
- wifi
- miniPCIe slot
- USB port
- microSD slot
- sysupgrade
- reset button
Installation and recovery:
In order to install OpenWRT the first time or recover the router, you
can use the web-based recovery system. Keep the reset button pressed
during boot and access 192.168.1.1 in your browser when your machine
obtains an IP address. Upload the firmware to start the recovery
process.
How to swap SIMs:
You control which SIM slot to use by writing 0/1 to
/sys/class/gpio/gpio13/value. In order for the change to take effect,
you can either use AT-commands (AT+CFUN) or power-cycle the modem (write
0/1 to /sys/class/gpio/gpio14/value).
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
Head Weblink HDRM200 is a dual-sim router based on MT7620A. The detailed
specifications are:
- MT7620A (580MHz)
- 64MB RAM
- 16MB of flash (SPI NOR)
- 6x 10/100Mbps Ethernet (MT7620A built-in switch)
- 1x microSD slot
- 1x miniPCIe slot (only USB2.0 bus). Device is shipped with a SIMCOM
SIM7100E LTE modem.
- 2x SIM slots (standard size)
- 1x USB2.0 port
- 1x 2.4GHz wifi (rt2800)
- 1x 5GHz wifi (mt7612)
- 1x reset button
- 1x WPS button
- 3x GPIO-controllable LEDs
- 1x 10 pin terminal block (RS232, RS485, 4 x GPIO)
Tested:
- Ethernet switch
- Wifi
- USB slot
- SD card slot
- miniPCIe-slot
- sysupgrade
- reset button
Installation instructions:
Installing OpenWRT for the first time requires a bit of work, as the
board does not ship with OpenWRT. In addition, the bootloader
automatically reboots when installing an image over tftp. In order to
install OpenWRT on the HDRM200, you need to do the following:
* Copy the initramfs-image to your tftp-root (default filename is
test.bin) and configure networking accordingly (default server IP is
10.10.10.3, client 10.10.10.123). Start your tftp server.
* Open the board and connect to UART. The pins are exposed and clearly
marked.
* Boot the board and press 1.
* Either use the default filename and client/server IP-addresses, or
specify your own.
The image should now be loaded to memory and board boot. If the router
reboots while the image is loading, you need to try again. Once the
board has booted, copy the sysupgrade-image to the router and run
sysupgrade in order to install OpenWRT to the flash.
Notes:
- You control which SIM slot to use by writing 0/1 to
/sys/class/gpio/gpio0/value. In order for the change to take
effect, you can either use AT-commands (AT+CFUN) or power-cycle the
modem (write 0/1 to /sys/class/gpio/gpio21/value).
- RS485 is available on /dev/ttyS0.
- RS232 is available on /dev/ttyS1.
- The name of the ioX-gpios map to the labels on the casing.
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
[fixed whitespace issue and merge conflict in target.mk]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
The factory firmware omits the JFFS2 end-marker while flashing via
web-interface. Add a 64k padding after the marker fixes this problem.
When the end-marker is not present, OpenWRT won't save the overlayfs
after initial flash.
Reported-by: Andreas Ziegler <dev@andreas-ziegler.de>
Signed-off-by: David Bauer <mail@david-bauer.net>
It's OEM module with 2*26 pin header, similar to LinkIt Smart 7688 or
Vocore2.
Specification:
CPU: MT7628 580 MHz. MIPS 24K
RAM: 64 MB
Flash: 8 MB
WIFI: 802.11n/g/b 20/40 MHz
USB: 1x Port USB 2.0
Ethernet: 5 Port ethernet switch
UART: 2x
Installation: Use the installed uboot Bootloader. Connect a serial cable
to serialport 0. Turn power on. Choose the option: "Load system code
then write to Flash via TFTP". Choose the local device IP and the TFTP
server IP and the file name of the system image. After if the
Bootloader will copy the image to the local flash.
Notes: The I2C Kernel module work not correctly. You can send and
receive data. But the command i2cdetect doesn’t work. FS#845
Signed-off-by: Eike Feldmann <eike.feldmann@outlook.com>
[commit subject and message touches, DTS whitespace fixes, wifi LED
rename, pinctrl fixes, network settings fixes, lan/wmac mac addresses,
removed i2c kernel modules]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Hardware
--------
SoC: MediaTek MT7628NN
RAM: 64M DDR2 (Etron EM68B16CWQD-25H)
FLASH: 8M (Winbond W25Q64JVSIQ)
LED: Power - WLAN
BTN: Reset
UART: 115200 8N1
TX and RX are labled on the board as pads next to the SoC
Installation via web-interface
------------------------------
1. Visit the web-interface at 192.168.8.1
Note: The ethernet port is by default WAN. So you need to connect to
the router via WiFi
2. Navigate to the Update tab on the left side.
3. Select "Local Update"
4. Upload the OpenWrt sysupgrade image.
Note: Make sure you select not to preserve the configuration.
Installation via U-Boot
-----------------------
1. Hold down the reset button while powering on the device.
Wait for the LED to flash 5 times.
2. Assign yourself a static IPv4 in 192.168.1.0/24
3. Upload the OpenWrt sysupgrade image at 192.168.1.1.
Signed-off-by: David Bauer <mail@david-bauer.net>
Hardware spec:
CPU: MTK MT7621A
RAM: 256MB
ROM: 16MB SPI Flash
WiFi: MT7603EN + MT7612EN
Button: 2 buttons (reset, wps)
LED: 8 LEDs (Power 2G 5G WPS Internet LAN1 LAN2 USB)
Ethernet: 3 ports, 2 LAN + 1 WAN
Other: USB3.0
Flashing instructions:
Visit the openwrt forum topic for this router:
https://forum.openwrt.org/t/add-openwrt-support-for-youku-yk-l2/34692
to get the bootloader and unlock firmware.
0. upgrade your router with the telnet firmware via the
firmware upgrade page on the webui.
1. telnet 192.168.11.1 from your PC
2. Download the pb-boot-youku_l2-20190317-61b6d33.bin and transfer
it to the /tmp directory of the router.
3. mtd write /tmp/pb-boot-youku_l2-20190317-61b6d33.bin Bootloader
4. turn off the power
5. Push the reset button while turning on the router and
wait until LED start blinking (~10sec.)
6. Connect Ethernet port and goto http://192.168.1.1.
7. Upload the firmware to firmware restore page in webui.
Signed-off-by: Zhao Yu <574249312@qq.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [rewrote the
flashing instructions, fixed author]
SoC: MediaTek MT7621
RAM: 64M (Winbond W9751G6KB-25)
FLASH: 16MB (Macronix MX25L12835F)
WiFi: MediaTek MT7662E bgn 2SS
WiFi: MediaTek MT7662E nac 2SS
BTN: ON/OFF - Reset - WPS - AP/Extender toggle
LED: - Arrow Right (blue)
- Arrow Left (blue)
- WiFi 1 (red/green)
- WiFi 2 (red/green)
- Power (green/amber)
- WPS (Green)
UART: UART is present as Pads on the backside of the PCB. They are
located on the other side of the Ethernet port.
3.3V - GND - TX - RX / 57600-8N1
3.3V is the nearest one to the antenna connectors
Installation
------------
Update the factory image via the Netgear web-interfaces (by default:
192.168.1.250/24).
You can also use the factory image with the nmrpflash tool.
For more information see https://github.com/jclehner/nmrpflash
Signed-off-by: David Bauer <mail@david-bauer.net>
[merge conflict in 02_network, flash@0 node rename, wlan DTS triggers]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Device specification:
- SoC: RT5350F
- CPU Frequency: 360 MHz
- Flash Chip: Winbond 25Q32 (4096 KiB)
- RAM: 32768 KiB
- 5x 10/100 Mbps Ethernet (4x LAN, 1x WAN)
- 1x external, non-detachable antenna
- UART (J1) header on PCB (57800 8n1)
- Wireless: SoC-intergated: 2.4GHz 802.11bgn
- USB: None
- 3x LED, 2x button
Flash instruction:
1. Configure PC with static IP 192.168.1.2/24 and start TFTP server.
2. Rename "openwrt-ramips-rt305x-kn_st-squashfs-sysupgrade.bin"
to "kstart_recovery.bin" and place it in TFTP server directory.
3. Connect PC with one of LAN ports, press the reset button, power up
the router and keep button pressed until power LED start blinking.
4. Router will download file from TFTP server, write it to flash and reboot.
Signed-off-by: Vladimir Kot <vova28rus@gmail.com>
[fixed git commit author and whitespace issues in DTS]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
The WIZnet WizFi630S board is in the miniPCIe form factor.
SoC: Mediatek MT7688AN
RAM: 128MB
Flash: 32Mb
WiFi: 2.4GHz
Ethernet: 3x 100Mbit
USB: 1 (USB 2.0)
serial ports: 2 (1x full, 1xlite)
Flash and recovery instructions: Use the factory installed u-boot boot
loader. It is available on UART2 (115200,8,n,1). Then get the
sysupgrade image from a tftp server.
Signed-off-by: Tobias Welz <tw@wiznet.eu>
[whitespace and device name in makefile fixes]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
The DIR-510L Wireless Router are based on the MT7620A SoC.
Specification:
-MediaTek MT7620A (580 Mhz)
-128 MB of RAM
-16 MB of FLASH
-802.11bgn radio
-1x 10/100 Mbps Ethernet
-2x internal, non-detachable antennas
-UART (J3) header on PCB (57600 8n1)
-1x bi-color LED (GPIO-controlled), 2x button
-JBOOT bootloader
Known issues:
-Ethernet port is used as LAN
-No communication with charger IC. (uart bitbang needed)
Installation:
Apply factory image via d-link http web-gui.
How to revert to OEM firmware:
1.) Push the reset button and turn on the power. Wait until LED start blinking (~10sec.)
2.) Upload original factory image via JBOOT http (IP: 192.168.123.254)
3.) If http doesn't work, it can be done with curl command:
curl -F FN=@XXXXX.binhttp://192.168.123.254/upg
where XXXXX.bin is name of firmware file.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
[fixed whitespace issue in 10-rt2x00-eeprom]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Some boards with JBOOT have partiton between bootloader
and kernel image. This patch add possibility to change kernel
partition start address.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
- Former "mir3g" board name becomes "xiaomi,mir3g".
- Reorder some entries to maintain alphabetical order.
- Change DTS so status LEDs (yellow/red/blue) mimic
Xiaomi stock firmware: (Section Indicator)
<http://files.xiaomi-mi.co.uk/files/router_pro/router%20PRO%20EN.pdf>
<http://files.xiaomi-mi.co.uk/files/Mi_WiFi_router_3/MiWiFi_router3_EN.pdf>
|Yellow: Update (LED flickering), the launch of the system (steady light);
|Blue: during normal operation (steady light);
|Red: Safe mode (display flicker), system failure (steady light);
Signed-off-by: Ozgur Can Leonard <ozgurcan@gmail.com>
[Added link to similar Router 3 model]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Hardware:
CPU: MediaTek MT7621AT (2x880MHz)
RAM: 512MB DDR3
FLASH: 256MB NAND
WiFi: 2.4GHz 4x4 MT7615 b/g/n (Needs driver, See Issues!)
WiFI: 5GHz 4x4 MT7615 a/n/ac (Needs driver, See Issues!)
USB: 1x 3.0
ETH: 1x WAN 10/100/1000 3x LAN 10/100/1000
LED: Power/Status
BTN: RESET
UART: 115200 8n1
Partition layout and boot:
Stock Xiaomi firmware has the MTD split into (among others)
- kernel0 (@0x200000)
- kernel1 (@0x600000)
- rootfs0
- rootfs1
- overlay (ubi)
Xiaomi uboot expects to find kernels at 0x200000 & 0x600000
referred to as system 1 & system 2 respectively.
a kernel is considered suitable for handing control over
if its linux magic number exists & uImage CRC are correct.
If either of those conditions fail, a matching sys'n'_fail flag
is set in uboot env & a restart performed in the hope that the
alternate kernel is okay.
If neither kernel checksums ok and both are marked failed, system 2
is booted anyway.
Note uboot's tftp flash install writes the transferred
image to both kernel partitions.
Installation:
Similar to the Xiaomi MIR3G, we keep stock Xiaomi firmware in
kernel0 for ease of recovery, and install OpenWRT into kernel1 and
after.
The installation file for OpenWRT is a *squashfs-factory.bin file that
contains the kernel and a ubi partition. This is flashed as follows:
nvram set flag_try_sys1_failed=1
nvram set flag_try_sys2_failed=0
nvram commit
dd if=factory.bin bs=1M count=4 | mtd write - kernel1
dd if=factory.bin bs=1M skip=4 | mtd write - rootfs0
reboot
Reverting to stock:
The part of stock firmware we've kept in kernel0 allows us to run stock
recovery, which will re-flash stock firmware from a *.bin file on a USB.
For this we do the following:
fw_setenv flag_try_sys1_failed 0
fw_setenv flag_try_sys2_failed 1
reboot
After reboot the LED status light will blink red, at which point pressing
the 'reset' button will cause stock firmware to be installed from USB.
Issues:
OpenWRT currently does not have support for the MT7615 wifi chips. There is
ongoing work to add mt7615 support to the open source mt76 driver. Until that
support is in place, there are closed-source kernel modules that can be used.
See: https://forum.openwrt.org/t/support-for-xiaomi-wifi-r3p-pro/20290/170
Signed-off-by: Ozgur Can Leonard <ozgurcan@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[02_network remaps, Added link to notes]
ALFA Network Tube-E4G is an outdoor, dual-SIM LTE Cat. 4 CPE, based on
MediaTek MT7620A, equipped with Quectel EC25 miniPCIe modem.
Specification:
- MT7620A (580 MHz)
- 64/128/256 MB of RAM (DDR2)
- 16/32 MB of flash (SPI NOR)
- 1x 10/100 Mbps Ethernet, with passive PoE support (24 V)
- 1x miniPCIe slot (with PCIe and USB 2.0 buses)
- 2x SIM slot (mini, micro) with detect and switch driven by GPIO
- 1x detachable antenna (modem main)
- 1x internal antenna (modem div)
- 1x GPS passive antenna (optional)
- 5x LED (all driven by GPIO)
- 1x button (reset)
- UART (4-pin, 2.54 mm pitch) header on PCB
Other:
Default SIM slot is selected at an early stage by U-Boot, based on
'default_sim' environment value: 1 or unset = SIM1 (mini), 2 = SIM2
(micro). U-Boot also resets the modem, using #PERST signal, before
starting kernel.
Flash instruction:
You can use the 'sysupgrade' image directly in vendor firmware which is
based on OpenWrt (make sure to not preserve settings - use 'sysupgrade
-n -F ...' command). Alternatively, use web recovery mode in U-Boot:
1. Power the device with reset button pressed, the LAN LED will start
blinking slowly and after ~3 seconds, when it starts blinking faster,
you can release the button.
2. Setup static IP 192.168.1.2/24 on your PC.
3. Go to 192.168.1.1 in browser and upload 'sysupgrade' image.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Device specification:
- SoC: Ralink RT3883 (MIPS 74Kc) 500Mhz
- RAM: 64Mb
- Flash: 8MB (SPI-NOR)
- Ethernet: 10/100/1000 Mbps
- WLAN
Wireless 1: SoC-integrated : 2.4/5 GHz
Wireless 2: 2.4 GHz RT3092L
- LED: 2x USB, WAN, LAN
- Key: WPS, reset
- Serial: 4-pin header, (57600,8,N,1), 3.3V TTL,
GND, RX, TX, V - J12 marking on board
- USB ports: 2 x USB 2.0
Flashing instructions:
Option 1 (from bootloader web)
- Hold reset button on the back of router when plugging
in power (for at-least 10 seconds after plugged in)
- Connect to a Lan port
- Set computer IP to 10.10.10.3
- Go to http://10.10.10.123 in a web browser
- Click the Browse... Button and select the
*squashfs.sysupgrade.bin file then click APPLY
Option 2 (from the stock admin web)
- Go to firmware upgrade
- Upload the **factory** image *initramfs.bin first
- Boot into openwrt
- From Luci web in openwrt upload the *squashfs.sysupgrade.bin
Signed-off-by: Kip Porterfield <kip.porterfield@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[added v1 to the compatible identifier, added pciid for
the RT3092L, fixed pci unit-address, split out the F9K110X.dtsi
to prepare for a possible F9K1103 patch]
This patch adds support for the TP-Link TL-WR802N-v4.
https://openwrt.org/toh/tp-link/tl-wr802n
Specification:
- MT7628N (580 MHz)
- 64 MB RAM
- 8 MB FLASH
- 2T2R 2.4 GHz
- 1x 10/100 Mbps Ethernet
- 1x LED
Flash instruction:
The only way to flash the image in TL-WR802N v4 is to use
tftp recovery mode in U-Boot:
1. Configure PC with static IP 192.168.0.225/24 and tftp server.
2. Rename "openwrt-ramips-mt76x8-tplink_tl-wr802n-v4-squashfs-tftp-recovery.bin"
to "tp_recovery.bin" and place it in tftp server directory.
3. Connect PC with the LAN port, press the reset button, power up
the router and keep button pressed for around 10 seconds, until
device starts downloading the file.
4. Router will download file from server, write it to flash and reboot.
Signed-off-by: Marcel Jost <majo@icutech.ch>
The WeVo 11AC NAS has a MT7612E 802.11ac chip on the PCB.
Signed-off-by: Ju Se Hoon <joosahoon@gmail.com>
[renamed author from Albis-dev to real name, editted commit message]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This adds support for the TP-Link Archer C50 v4.
It uses the same hardware as the v3 variant, sharing the same FCC-ID.
CPU: MediaTek MT7628 (580MHz)
RAM: 64M DDR2
FLASH: 8M SPI
WiFi: 2.4GHz 2x2 MT7628 b/g/n integrated
WiFI: 5GHz 2x2 MT7612 a/n/ac
ETH: 1x WAN 4x LAN
LED: Power, WiFi2, WiFi5, LAN, WAN, WPS
BTN: WPS/WiFi, RESET
UART: Near ETH ports, 115200 8n1, TP-Link pinout
Create Factory image
--------------------
As all installation methods require a U-Boot to be integrated into the
Image (and we do not ship one with the image) we are not able to create
an image in the OpenWRT build-process.
Download a TP-Link image from their Wesite and a OpenWRT sysupgrade
image for the device and build yourself a factory image like following:
TP-Link image: tpl.bin
OpenWRT sysupgrade image: owrt.bin
> dd if=tpl.bin of=boot.bin bs=131584 count=1
> cat owrt.bin >> boot.bin
Installing via Web-UI
---------------------
Upload the boot.bin via TP-Links firmware upgrade tool in the
web-interface.
Installing via Recovery
-----------------------
Activate Web-Recovery by beginning the upgrade Process with a
Firmware-Image from TP-Link. After starting the Firmware Upgrade,
wait ~3 seconds (When update status is switching to 0%), then
disconnect the power supply from the device. Upgrade flag (which
activates Web-Recovery) is written before the OS-image is touched and
removed after write is succesfull, so this procedure should be safe.
Plug the power back in. It will come up in Recovery-Mode on 192.168.0.1.
When active, all LEDs but the WPS LED are off.
Remeber to assign yourself a static IP-address as DHCP is not active in
this mode.
The boot.bin can now be uploaded and flashed using the web-recovery.
Installing via TFTP
-------------------
Prepare an image like following (Filenames from factory image steps
apply here)
> dd if=/dev/zero of=tp_recovery.bin bs=196608 count=1
> dd if=tpl.bin of=tmp.bin bs=131584 count=1
> dd if=tmp.bin of=boot.bin bs=512 skip=1
> cat boot.bin >> tp_recovery.bin
> cat owrt.bin >> tp_recovery.bin
Place tp_recovery.bin in root directory of TFTP server and listen on
192.168.0.66/24.
Connect router LAN ports with your computer and power up the router
while pressing the reset button. The router will download the image via
tftp and after ~1 Minute reboot into OpenWRT.
U-Boot CLI
----------
U-Boot CLI can be activated by holding down '4' on bootup.
Dual U-Boot
-----------
This is the first TP-Link MediaTek device to feature a split-uboot
design. The first (factory-uboot) provides recovery via TFTP and HTTP,
jumping straight into the second (firmware-uboot) if no recovery needs
to be performed. The firmware-uboot unpacks and executed the kernel.
Web-Recovery
------------
TP-Link integrated a new Web-Recovery like the one on the Archer C7v4 /
TL-WR1043v5. Stock-firmware sets a flag in the "romfile" partition
before beginning to write and removes it afterwards. If the router boots
with this flag set, bootloader will automatically start Web-recovery and
listens on 192.168.0.1. This way, the vendor-firmware or an OpenWRT
factory image can be written.
By doing the same while performing sysupgrade, we can take advantage of
the Web-recovery in OpenWRT.
It is important to note that Web-Recovery is only based on this flag. It
can't detect e.g. a crashing kernel or other means. Once activated it
won't boot the OS before a recovery action (either via TFTP or HTTP) is
performed. This recovery-mode is indicated by an illuminated WPS-LED on
boot.
Signed-off-by: David Bauer <mail@david-bauer.net>
Move the zip compression into a build recipe. Pad the image using the
existing build recipes as well to remove duplicate functionality
Change the code to append header and footer in two steps. Allow to use a
fixed filename as the netgear update image does.
Use a fixed timestamp within the zip archive to make the images
reproducible.
Due to the changes we are now compatible to the gnu89 c standard used by
default on the buildbots and we don't need to force a more recent
standard anymore.
Beside all changes, the footer still looks wrong in compare to the
netgear update image.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Always enable the pwr led and use the usr led for boot status indication.
Rename nodes in the dts, to match what is recommend in the devicetree
specification.
Increase the maximum spi frequency to 20MHz and drop the m25p,chunked-io
which isn't required on mt7621.
Use the BTN_0 keycode for the mode button. This board doesn't have any
wireless.
Use a more descriptive label for the reset button and the GPIO enabling
the usb vcc supply.
Use the beeper kernel module for the buzzer.
Fix the pinmux to switch only pins used as GPIOs to the GPIO function.
Add support for the PoE enable GPIO to the userspace. The PoE power
status can be read via GPIO7. Since OpenWrt doesn't have support for
reading inputs from userspace, prepare only the pinmux for the GPIO.
Signed-off-by: Anton Arapov <arapov@gmail.com>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
Signed-off-by: Mathias Kresin <dev@kresin.me>
This patch adds support of MikroTik RouterBOARD 750Gr3, without the need
to reflashing the bootloader.
Installation through RouterBoot follows the usual MikroTik method
https://openwrt.org/toh/mikrotik/common
Since the image isn't compatible with RouterBOARD 750Gr3 installations
which have replaced the bootloader, the former used userspace boardname
is not added to the SUPPORTED_DEVICES, to prevent a brick while trying
to upgrade to the image with native support.
Signed-off-by: Anton Arapov <arapov@gmail.com>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
Signed-off-by: Mathias Kresin <dev@kresin.me>
Create a common template which has the required image build code
defined. Add some new variables to pass individual parts to the seama
recipes.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Specs
SoC: MT7621AT
RAM: 512MiB
Flash: 32MiB MX25L25635F SPI NOR
2.4G: MT7603EN
5G: MT7612EN
Ethernet: 4x GE ports (1x WAN, 3x LAN) with link status LEDs
USB 3.0
LEDs: POWER, 5G WIFI, 2.4G WIFI, USB, Internet.
The last two ones are controlled by GPIO
UART: There are 2 UARTs (UARTLITE1/ttyS0 and UARTLITE3/ttyS1) on board.
UARTLITE1 is close to LEDs, and UARTLITE3 is close to flash chip.
The stock u-boot uses UARTLITE1 by default. Baud rate is 57600
Flash instruction
1. telnet 192.168.9.1 2317, username is "root" and password is "admin"
One can alternatively use UART to log in
2. Put OpenWrt firmware in a FAT32 USB drive, and connect it to the router
One can alternatively download the firmware via wget through Internet
3. mtd write /path/to/openwrt.bin firmware
4. reboot
Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
Very similar to the DWR-921-C1, except has a telephony/RJ11 port (not
sure if supported, I didn't try), wireless router with QMI LTE embedded
modem is based on the MT7620N SoC.
Specification:
* MediaTek MT7620N (580 Mhz)
* 64 MB of RAM
* 16 MB of FLASH
* 802.11bgn radio
* 5x 10/100 Mbps Ethernet (1 WAN and 4 LAN)
* 2x external, detachable (LTE) antennas
* UART header on PCB (57600 8n1)
* 6x LED (GPIO-controlled)
* 1x bi-color Signal Strength LED (GPIO-controlled)
* 2x button
* JBOOT bootloader
The status led has been assigned to the dwr-922-e2:green:signalstrength
(lte signal strength) led. At the end of the boot it is switched off and
is available for lte operation. Works correctly also during sysupgrade
operation.
Installation:
Apply factory image via d-link http web-gui, or via recovery interface:
How to recover/revert to OEM firmware:
1.) Push and hold the reset button and turn on the power. Wait until all
LEDs start rapidly blinking (~10sec.)
2.) DHCP should give you an IP in the 192.168.123.0/24 subnet, or set
one manually
3.) Upload original factory image via JBOOT http interface at IP
192.168.123.254
4.) If http doesn't work, it can be done with curl command:
curl -F FN=@XXXXX.binhttp://192.168.123.254/upg
where XXXXX.bin is name of firmware file.
5.) You can optionally telnet to 192.168.123.254 before or during the
upload and it will report the flashing status, memory address etc.
6.) Once web UI and/or telnet says "Success", power cycle the router, or
type "reboot" into the telnet session.
Signed-off-by: Simon Quigley <squigley@squigley.net>
[squashed commits, word wrap commit message, rename signal strenght led
name to match what is used for the DWR-921-C1 since they share the led
configuration, add label referenced in the aliases node]
Signed-off-by: Mathias Kresin <dev@kresin.me>
Netgear R6350 is a wireless router, aka Netgear AC1750.
Specification:
- SoC: Mediatek MT7621AT (2 CPU cores, 4 threads)
- RAM: 128MiB (Nanya NT5CC64M16GP-DI)
- ROM: 128MiB NAND Flash (Macronix MX30LF1G18AC-TI)
- Wireless:
for 11b/g/n (upto 300Mbps): MT7603
for 11a/ac (upto 1450Mbps) : MT7615, is not avaliable now
- Ethernet LAN speed: up to 1000Mbps
- Ethernet LAN ports: 4
- Ethernet WAN speed: up to 1000Mbps
- Ethernet WAN ports: 1
- USB ports: 1 (USB 2.0)
- LEDs: 4 (all can be controlled by SoC's GPIO)
- buttons: 2
- serial ports: unknown
Installation through telnet:
- Copy kernel.bin and rootfs.bin to a USB flash disk,
plug to usb port on the router.
- Enable telnet with link: http://192.168.1.1/setup.cgi?todo=debug
(login if required, default: admin password)
- You will see "Debug Enabled!"
- Telnet 192.168.1.1 and login with "root"
- ls /mnt/shares/ to find out path of your USB disk.
'myUdisk' for example.
- cd /mnt/shares/myUdisk
- mtd_write write rootfs.bin Rootfs
- mtd_write write kernel.bin Kernel
- reboot
recovery when bricked:
nmrpflash can be used to recover to the netgear firmware
if a broken image was flashed.
The SC_PART_MAP partition suggests that an on flash partition table
exists. After implementing a partition parser/builder for the sercom
partition format, the definitions don't match the flash layout used by
the stock firmware.
It either means the partition format has not yet been completely
understood or it isn't used by the stock firmware. For now, use fixed
partitions instead.
Signed-off-by: NOGUCHI Hiroshi <drvlabo@gmail.com>
[apply latest ramips changes and document the on flash partition map
issues]
Signed-off-by: Mathias Kresin <dev@kresin.me>
INAGAKI Hiroshi
Andreas Böhler
Adrian Schmutzler
David Bauer
Steffen Förster
Petr Štetiar
Maxim Anisimov
Yong-hyu Ban
Mason Clarke
Maksym Medvedev
Sungbo Eo
DENG Qingfang
Piotr Dymacz
Frederik Noe-Sdun
Paul Spooren
Kristian Evensen
Paul Fertser
Gabor Varga
Roger Pueyo Centelles
Qi Jiang
Nick Briggs
Daniel Danzberger
Birger Koblitz
Ivan Hörler
Chuanhong Guo
Christoph Krapp
Christian Lamparter
Zhenjian Zhang
Daniel Golle
Felix Fietkau
Ozgur Can Leonard
NOGUCHI Hiroshi
Georgi Vlaev
Alexander Müller
Jan Hoffmann
Markus Scheck
Davide Fioravanti
Nicholas Smith
Liu Yu
Eike Feldmann
Zhao Yu
Vladimir Kot
Tobias Welz
Pawel Dembicki
Kip Porterfield
Marcel Jost
Thomas Vincent-Cross
Ju Se Hoon
Mathias Kresin
Anton Arapov
Simon Quigley
Weijie Gao