This patch adds the posibility to config the led behaviour of the lantiq phys
over the devicetree bindings.It patches the 0023-NET-PHY-adds-driver-for-lantiq-PHY11G
for 3.18 and 4.1. I have also added a register description overview for
applicable values. This goes to the documentation folder in the linux kernel.
Signed-off-by: Florian Eckert <Eckert.Florian@googlemail.com>
SVN-Revision: 47566
It turned out that mtk_nand driver uses some sophisticated accounting and a
general nand code must be patched.
This patch adds required read and erase calls to a general nand code. I
used a code for re6500 released by Linksys as a reference.
All required operations (erase, write and read) are usable. However I found
that jffs2 filesystem can be created only on top of a ubi volume. I tried
to create jffs2 directly on mtd device but pages with clean markers are
became uncorrectable.
Signed-off-by: Kirill Berezin <fyiwdt@gmail.com>
SVN-Revision: 47565
All RTC drivers require the kernel to be built with CONFIG_RTC_CLASS=y.
Set it accordingly.
Tested only with DS1307.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
SVN-Revision: 47564
This patch improves the default configuration of DWC2 on lantiq SoCs
somewhat:
* Set maximum packet count to largest allowed value by the DWC2 (511)
* Use 16-bit DMA bursts
* Divide fifo buffers more evenly
Default fifo buffer sizes from original ltq-hcd driver seem really
irrational. For example according to DWC2 data book rxfifo size of 240
will not fit even a single full length USB packet. On the other hand
non-periodic tx fifo size of 240 is more than enough to fit one complete
packet.
Change the sizes around to improve the situation and to fix some issues
especially with isochronous USB transfers.
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
SVN-Revision: 47563
The hwid check was wrong, causing the AR71XX_MODEL value to end with a
space (as $hwver was unset).
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 47553
r47218 was missing needed changes which were accidentally
ommitted from the patch.
This should fix#20878
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 47552
When fixing the model string for WNDR3700v2 which contain a model string
followed by 0xff in r46455, the match for other versions of the WNDR3700v2
which just contain lots of 0xff broke (as the 0xff $model is checked for
is stripped off).
Fix by stripping off non-printable characters only for the actual output
string, but not for the internal matching.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 47538
gcc-5 handles inline without static differently and that makes
uboot-mxs fail to build. Remove the inline so it gets exported and can
be used in other functions.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 47533
Removed video related kernel params that are only appropriate for the
Freescale downstream vendor kernel and not appriate for mainline linux.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
SVN-Revision: 47532
The 206-ARM-imx-ventana-added-GW16083-to-device-tree.patch merged wrong in
the conversion from 3.18 to 4.1. This patch resolves that and puts the
device-tree nodes in the correct place.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
SVN-Revision: 47510
Replace the ventana ubi images from a single rootfs volume containing the
rootfs as well as kernel+dtbs in the boot/ subdir to a multi-volume ubi
containing kernel+dtbs+bootscript in 'root' ubifs volume, rootfs in 'rootfs'
squasfs volume, and rootfs_data an empty ubifs volume.
At the same time move ventana image creation over to using the new
TARGET_DEVICE syntax as a cleanup.
Additionally removed FIT image creation as it is recommended that this be
done manually to produce signed FIT images if needed.
Note that a bootscript is needed for Ventana to change its default mtdparts
to rename the 2nd partition from 'rootfs' to 'ubi'. This is because there
are patches in OpenWrt kernels that try to auto-attach and auto-mount and these
get in the way if the mtd partition is named 'rootfs'.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
SVN-Revision: 47508
Upstream patch: e9d6d6b62f306ba83e1441af5daf2809a6167474
Add support for the Gateworks GW5510 board featuring:
* i.MX6 SoC
* up to 512MB DDR3
* up to 2GB NAND flash
* 1x miniPCIe socket (with USB)
* HDMI out (micro-HDMI)
* HDMI in (micro-HDMI) (currently supported by only vendor kernel)
* TTL level I/O (supported by GW16111 breakout board):
* I2C
* 2x UART
* CAN
* 2x DIO (GPIO/PWM)
* USB OTG
Also add support to OpenWrt build system
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Pushpal Sidhu <psidhu@gateworks.com>
SVN-Revision: 47505
John Crispin
Hauke Mehrtens
Felix Fietkau
Jo-Philipp Wich
Luka Perkov
Zoltan Herpai
Steven Barth