Commit Graph

123 Commits (141698ce8fbc52d253c9207ef46b3630a0870567)

Author SHA1 Message Date
Adrian Schmutzler 141698ce8f ath79: Add support for TP-Link CPE210 v2
This PR adds support for a popular low-cost 2.4GHz N based AP

Specifications:
 - SoC: Qualcomm Atheros QCA9533 (650MHz)
 - RAM: 64MB
 - Storage: 8 MB SPI NOR
 - Wireless: 2.4GHz N based built into SoC 2x2
 - Ethernet: 1x 100/10 Mbps, integrated into SoC, 24V POE IN

Installation:
Flash factory image through stock firmware WEB UI
or through TFTP
To get to TFTP recovery just hold reset button while powering on
for around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP adress:192.168.0.254

This is based on the support patch for the identical CPE210 v3
by Mario Schroen <m.schroen@web.de>.

Tested-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
[renamed dtsi filename]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
5 years ago
Mario Schroen 5ec205d7ac ath79: Add support for TP-Link CPE210 v3
Specifications:

    * SoC: Qualcomm Atheros QCA9533 (650MHz)
    * RAM: 64MB
    * Storage: 8 MB SPI NOR
    * Wireless: 2.4GHz N based built into SoC 2x2
    * Ethernet: 1x 100/10 Mbps, integrated into SoC, 24V POE IN

Installation:
    Flash factory image through stock firmware WEB UI or TFTP
    To get to TFTP recovery just hold reset button while powering
    on for around 4-5 seconds and release.
    Rename factory image to recovery.bin
    Stock TFTP server IP:192.168.0.100
    Stock device TFTP adress:192.168.0.254

Thanks to robimarko for the work inside the ar71xx tree.
Thanks to adrianschmutzler for deep discussion and fixes.

Signed-off-by: Mario Schroen <m.schroen@web.de>
[Split into DTS/DTSI, read-only config partition in DTSI]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
[renamed dtsi filename, light subject touches]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
5 years ago
Ding Tengfei acf149d531 ath79: add support for COMFAST CF-E5/E7
COMFAST CF-E5/E7 is a outdoor 4G LTE AP with PoE support, based on
Qualcomm/Atheros QCA9531.

Short specification:

    2x 10/100 Mbps Ethernet, with 24v PoE support
    64 MB of RAM (DDR2)
    16 MB of FLASH (SPI)
    2T2R 2.4 GHz, 802.11b/g/n
    built-in 1x 3 dBi antennas
    output power (max): 80 mW (19 dBm)
    Qucetel EC20 LTE MODULE(1x external detachable antenna)

Flash instruction:

Original firmware is based on OpenWrt.
Use sysupgrade image directly in vendor GUI.

Signed-off-by: Ding Tengfei <dtf@comfast.cn>
[commit subject fix]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
5 years ago
Marcin Jurkowski fcc716e21d ath79: add TP-Link TL-WR710N v1
This commit adds support for TP-Link TL-WR710N v1 router.

CPU: Atheros AR9331 400MHz
RAM: 32MB
FLASH: 8MiB
PORTS: 1 Port 100/10 LAN (connected to a switch), 1 Port 100/10 WAN
WiFi: Atheros AR9331 1x2:1 bgn
USB: ChipIdea HDRC USB2.0
LED: SYS
BTN: Reset

Sysupgrade from `ar71xx` works without glitches.
Network interfaces assigned for LAN and WAN ports are `eth1` and `eth0`
respectively, what's consistent with `ar71xx` target. Wireless radio
path is automatically upgraded from `platform/ar933x_wmac` to
`platform/ahb/18100000.wmac`.

Signed-off-by: Marcin Jurkowski <marcin1j@gmail.com>
5 years ago
Chuanhong Guo 8de907c441 ath79: add support for TP-Link TL-WR941N v7 (CN)
This adds support for the Chinese version of TL-WR941N v7.
It uses QCA9558+AR8236 while the international version
uses TP9343 instead.

Specification:
- SoC: Qualcomm Atheros QCA9558
- Flash: 4 MB
- RAM: 64 MB
- Ethernet: Atheros AR8236 with 5 FE ports

Flash instruction:
  Upload the generated factory firmware on web interface.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
5 years ago
Tobias Schramm d78e229903 ath79: Add support for Ubiquiti NanoBeam AC
The NanoBeam is a small AR9342 based directional 5 GHz AC CPE with hardware
almost identical to the Ubiquiti NanoStation AC loco. Over the NanoStation
AC loco it has 5 additional LEDs. Four of those LEDs are used as rssi
indicators, the fifth LED is used as an ethernet link/activity indicator.

CPU:   Atheros AR9342 SoC
RAM:   64 MB DDR2
Flash: 16 MB NOR SPI
WLAN:  QCA988X
Ports: 1x GbE

Flashing procedure is identical to the NanoStation AC loco and can be performed
either via serial or the factory firmware upgrade.

Serial flashing:

1. Connect to serial header on device (8N1 115200)
2. Power on device and enter uboot console
3. Set up tftp server serving an openwrt initramfs build
4. Load initramfs build using the command tftpboot in the uboot cli
5. Boot the loaded image using the command bootm
6. Copy squashfs openwrt sysupgrade build to the booted device
7. Use mtd to write sysupgrade to partition "firmware"
8. Reboot and enjoy

Flashing through factory firmware:

1. Ensure firmware version v8.5.0.36727 is installed. Up/downgrade to this exact version.
2. Patch fwupdate.real binary using `hexdump -Cv /bin/ubntbox | sed 's/14 40 fe fe/00 00 00 00/g' | hexdump -R > /tmp/fwupdate.real`
3. Make the patched fwupdate.real binary executable using `chmod +x /tmp/fwupdate.real`
4. Copy the squashfs factory image to /tmp on the device
5. Flash OpenWRT using `/tmp/fwupdate.real -m <squashfs-factory image>`
6. Wait for the device to reboot

Thanks to @cybermaus for testing!

Tested-by: Maurits van Dueren den Hollander <cybermaus@gmail.com>
Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
5 years ago
Tomasz Maciej Nowak b3a0c97b8c ath79: add support for jjPlus JA76PF2
jjPlus JA76PF2 (marketed as IntellusPro2) is a network embedded board.

Specification
SoC:		Atheros AR7161
RAM:		64 MB DDR
Flash:		16 MB SPI NOR
Ethernet:	2x 10/100/1000 Mbps AR8316
		LAN (CN11), WAN/PoE (CN6 - close to power barrel
		connector, 48 V)
MiniPCI:	2x
LEDS:		4x, which 3 are GPIO controlled
Buttons:	2x GPIO controlled
		Reset (SW1, closer to ethernet ports), WPS (SW2)
Serial:		1x (only RX and TX are wired)
		baud: 115200, parity: none, flow control: none

Currently there is one caveat compared to ar71xx target images as the
MAC addresses are random on every reboot. To remedy this one needs to
store the WAN MAC address in RedBoot configuration. OpenWrt on first
boot, after flashing, will read out the address and assign proper ones
to both WAN and LAN ports. It is iportant to NOT keep the old
configuration when doing sysupgrade from ar71xx.

Upgrading from OpenWrt ar71xx image
1. Connect to serial port,
2. Download OpenWrt sysupgrade image to /tmp directory and flash it
   with:
    sysupgrade -n <openwrt_sysupgrade_image_name>
3. After writing new image OpenWrt will reboot, now interrupt boot
   process and enter RedBoot (bootloader) command line by pressing
   Ctrl+C,
4. Enter following commands (replace variable accordingly),
    set_mac (to view MAC addresses)
    alias ethaddr <wan_port_mac_adress>
    (confirm storing the value by inputting y and pressing Enter)
    reset
5. Now board should restart and boot OpenWrt with proper MAC addresses.

Installation
1. Prepare TFTP server with OpenWrt initramfs image,
2. Connect to WAN ethernet port,
3. Connect to serial port,
4. Power on the board and enter RedBoot (bootloader) command line by
   pressing Ctrl+C,
5. Enter following commands (replace variables accordingly):
    set_mac (to view MAC addresses)
    alias ethaddr <wan_port_mac_address>
    (confirm storing the value by inputting y and pressing Enter)
    ip_adress -l <board_ip_adress>/24 -h <tftp_server_ip_adress>
    load -r -b 0x80060000 <openwrt_initramfs_image_name>
    exec -c ""
6. Now board should boot OpenWrt initramfs image,
7. Download OpenWrt sysupgrade image to /tmp directory and flash it
   with:
    sysupgrade <openwrt_sysupgrade_image_name>
8. Wait few minutes, after the D2 LED will stop blinking, the board
   is ready for configuration.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
5 years ago
Tomasz Maciej Nowak ee34740ca3 ath79: add suport for EnGenius EPG5000
EnGenius EPG5000 (v1.0.0, marketed as IoT Gateway) is a dual band
wireless router.

Specification
SoC:		Qualcomm Atheros QCA9558
RAM:		256 MB DDR2
Flash:		16 MB SPI NOR
WIFI:		2.4 GHz 3T3R integrated
		5 GHz 3T3R QCA9880 Mini PCIe card
Ethernet:	5x 10/100/1000 Mbps QCA8337N
USB:		1x 2.0
LEDS:		4x GPIO controlled
Buttons:	2x GPIO controlled
UART:		4 pin header, starting count from white triangle on PCB
		1. VCC 3.3V, 2. GND, 3. TX, 4. RX
		baud: 115200, parity: none, flow control: none

Installation
1. Connect to one of LAN (yellow) ethernet ports,
2. Open router configuration interface,
3. Go to Tools > Firmware,
4. Select OpenWrt factory image with dlf extension and hit Apply,
5. Wait few minutes, after the Power LED will stop blinking, the router
   is ready for configuration.

Alternative installation
1. Prepare TFTP server with OpenWrt sysupgrade image,
2. Connect to one of LAN (yellow) ethernet ports,
3. Connect to UART port (leaving out VCC pin!),
4. Power on router,
5. When asked to enter a number 1 or 3 hit 2, this will select flashing
   image from TFTP server option,
6. You'll be prompted to enter TFTP server ip (default is 192.168.99.8),
   then router ip (default is 192.168.99.9) and for last, image name
   downloaded from TFTP server (default is uImageESR1200_1750),
7. After providing all information U-Boot will start flashing the image,
   You can observe progress on console, it'll take few minutes and when
   the Power LED will stop blinking, router is ready for configuration.

Additional information
If connected to UART, when prompted for number on boot, one can enter
number 4 to open bootloader (U-Boot) command line.
OEM firmware shell password is: aigo3d0a0tdagr
useful for creating backup of original firmware.
When doing upgrade from OpenWrt ar71xx image, it is recomended to not keep
the old configuration.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
5 years ago
Jeff Kletsky fefa34def8 ath79: Add GL.iNet AR-300M-Lite
AR300M-Lite is single-Ethernet variant of the AR300M series
Its eth0 would otherwise be assigned to the WAN interface
making it unreachable firstboot or failsafe.

Installation instructions from OEM (OpenWrt variant):
* Install sysupgrade.bin using OEM's "Advanced" GUI (LuCI),
   * Do not preserve settings
   * Access rebooted device via Ethernet at OpenWrt default address

Add previously missing LED defaults for all three variants;
-nand, -nor, -lite to the definitions in 01_leds

Non-lite variants thanks to Andreas Ziegler
https://patchwork.ozlabs.org/patch/1049396/

Runtime-tested:  GL.iNet AR300M-Lite

Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
5 years ago
Santiago Piccinini 24463d0d94 ath79: add support for LibreRouter v1
Hardware
--------
SOC:   QCA9558
RAM:   128M DDR2
Flash: 16MiB SPI-NOR
ETH:   QCA8337N: 2x 10/100/1000 PoE and PoE pass-through
WiFi2: QCA9558 (bgn) 2T2R
WiFi5: 2x mPCIE with AR9582 (an) 2T2R
BTN:   1x Reset
GPIO:  multiple GPIO on header, PoE passthrough enable
UART:  3.3V 115200 8N1 header on the board
WDG:   ATTiny13 watchdog
JTAG:  header on the board
USB:   1x connector and 1x header on the board
PoE:   10-32V input in ETH port 1, passthrough in port 2
mPCIE: 2x populated with radios (but replaceable)

OpenWrt is preinstalled from factory. To install use <your-image>-sysupgade.bin
using the web interface or with sysupgrade -n.

Flash from bootloader (in case failsafe does not work)
1. Connect the LibreRouter with a serial adapter (TTL voltage) to the UART
   header in the board.
2. Connect an ETH cable and configure static ip addres 192.168.1.10/24
3. Turn on the device and stop the bootloader sending any key through the serial
   interface.
4. Use a TFTP server to serve <your image>-sysupgrade.bin file.
5. Execute the following commands at the bootloader prompt:
    ath> tftp 82000000 <your image>-sysupgrade.bin
    ath> erase 0x9f050000 +$filesize
    ath> cp.b 0x82000000 0x9f050000 $filesize
    ath> bootm 0x9f050000

More docs
* Bootloader https://github.com/librerouterorg/u-boot
* Board details (schematics, gerbers): https://github.com/librerouterorg/board

Signed-off-by: Santiago Piccinini <spiccinini@altermundi.net>
5 years ago
Piotr Dymacz db91418766 ath79: add support for TP-Link RE350K v1
TP-Link RE350K v1 (FCC ID: TE7RE350K) is a wall-plug AC1200 Wi-Fi range
extender with 'Kasa Smart' support. Device is based on Qualcomm/Atheros
QCA9558 + QCA9882 + AR8035 platform and is available only on US market.

Specification:

- 720/600/200 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of flash (SPI NOR)
- 1x 1 Gbps Ethernet (AR8035)
- 2T2R 2.4 GHz (QCA9558), with ext. PA (SE2565T) and LNA (SKY65971-11)
- 2T2R 5 GHz (QCA9882), with ext. PA (SE5003L1-R) and LNA (SKY65981-11)
- 2x U.FL connector on PCB
- 2x dual-band PCB antennas
- 1x LED, 2x dual-color LED (all driven by GPIO)
- 3x button (app config, led, reset)
- 1x mechanical on/off slide switch
- 1x UART (4-pin, 2.54 mm pitch) header on PCB
- 1x JTAG (8-pin, 1.27 mm pitch) header on PCB

Flash instruction:
Use 'factory' image directly in vendor GUI (default IP: 192.168.0.254,
default credentials: admin/admin).

Warning:
This device does not include any kind of recovery mechanism in U-Boot.

Vendor firmware access:
You can access vendor firmware over serial (RX line requires jumper
resistor in R306 place, near XTAL) with: root/sohoadmin credentials.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
5 years ago
Piotr Dymacz 6fa94d5e8f ath79: add support for YunCore A770
YunCore A770 is a ceiling AC750 AP with 2 Fast Ethernet ports, PoE
(802.3at) support, based on QCA9531 + QCA9887.

Specification:

- 650/597/216 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of flash (SPI NOR)
- 2x 10/100 Mbps Ethernet (PoE 802.3at support in WAN port)
- 2T2R 2.4 GHz (QCA9531), with ext. PA and LNA
- 1T1R 5 GHz (QCA9887), with ext. FEM (SKY85728-11)
- 2x regular LED, 1x RGB LED (all driven by GPIO)
- 1x button (reset)
- DC jack for main power input (12 V)
- UART header on PCB

Flash instruction:

1. First, gain root access to the device, following below steps:

- Login into web gui (default password/IP: admin/192.168.188.253).
- Go to 'Advanced' -> 'Management' -> 'System' and download backup of
  configuration (bakfile.bin).
- Open the file as tar.gz archive, edit/update 'shadow' file and change
  hash of root password to something known.
- Repack the archive, rename it back to 'bakfile.bin' and use to
  restore configuration of the device.
- After that, device will reboot and can be accessed over SSH.

2. Then, install OpenWrt:

- Login over SSH and issue command:
  fw_setenv bootcmd "bootm 0x9f050000 || bootm 0x9fe80000"
- Upload 'sysupgrade' image and install it (only if previous command
  succeeded) with command: 'sysupgrade -n -F openwrt-...'.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
5 years ago
Petr Štetiar 40530c8eb4 ath79: Add support for Ubiquiti Nanostation M (XW)
CPU:  AR9342 SoC
RAM:      64 MB DDR2
Flash:     8 MB NOR SPI
Ports: 2x100 MBit (24V PoE in, 24V PoE out), AR8236 switch
WLAN:  2.4/5 GHz
UART:      1 UART
LEDs:        Power, 2x Ethernet, 4x RSSI LEDs (orange, red, 2x green)
Buttons:     Reset

Flashing instructions using recovery method over TFTP

 1. Unplug the ethernet cable from the router.
 2. Using paper clip press and hold the router's reset button. Make sure
    you can feel it depressed by the paper clip. Do not release the button
    until step 4.
 3. While keeping the reset button pressed in, plug the ethernet cable
    back into the AP. Keep the reset button depressed until you see the
    device's LEDs flashing in upgrade mode (alternating LED1/LED3 and
    LED2/LED4), this may take up to 25 seconds.
 4. You may release the reset button, now the device should be in TFTP
    transfer mode.
 5. Set a static IP on your Computer's NIC. A static IP of 192.168.1.25/24
    should work.
 6. Plug the PoE injector's LAN cable directly to your computer.
 7. Start tftp client and issue following commands:
     tftp> binary
     tftp> connect 192.168.1.20
     tftp> put openwrt-ath79-generic-ubnt-nano-m-xw-squashfs-factory.bin

Tested-by: Joe Ayers <ae6xe@arrl.net>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
5 years ago
Bart Lauret 4386054549 ath79: add support for TP-Link Archer C5 v1
TP-Link Archer C5 v1 is a dual band router
based on Qualcomm/Atheros QCA9558 + QCA9880.

Specification:

 - 720 MHz CPU
 - 128 MB of RAM (Various chips)
 - 16 MB of FLASH (Various chips)
 - SoC QCA9558 integrated 3T3R 2.4 GHz Wi-Fi
 - minipcie slot with 3T3R 5 GHz QCA9880-BR4A
 - 5x 10/100/1000 Mbps Ethernet (AR8327N Switch)
 - 10x LEDs, 2x software buttons

For further informwation on the device, visit the wiki:
<https://openwrt.org/toh/tp-link/archer-c5-c7-wdr7500>

Signed-off-by: Bart Lauret <bblauret@gmail.com>
5 years ago
INAGAKI Hiroshi 93d4439454 ath79: add support for I-O DATA WN-AC1600DGR
I-O DATA WN-AC1600DGR is a 2.4/5 GHz band 11ac router, based on
Qualcomm Atheros QCA9557.

Specification:

- SoC:      Qualcomm Atheros QCA9557
- RAM:      128 MB
- Flash:    16 MB
- WLAN:     2.4/5 GHz
  - 2.4 GHz: 2T2R (SoC internal)
  - 5 GHz:   3T3R (QCA9880)
- Ethernet: 5x 10/100/1000 Mbps
  - Switch: QCA8337N
- LED/key:  6x/6x(4x buttons, 1x slide switch)
- UART:     through-hole on PCB
  - Vcc, GND, TX, RX from ethernet port side
  - 115200n8

Flash instruction using factory image:

1. Connect the computer to the LAN port of WN-AC1600DGR
2. Connect power cable to WN-AC1600DGR and turn on it
3. Access to "http://192.168.0.1/" and open firmware update page
("ファームウェア")
4. Select the OpenWrt factory image and click update ("更新") button
5. Wait ~150 seconds to complete flashing

Alternative flash instruction using initramfs image:

1. Prepare a computer and TFTP server software with the IP address
"192.168.99.8" and renamed OpenWrt initramfs image
"uImageWN-AC1600DGR"
2. Connect between WN-AC1600DGR and the computer with UART
3. Connect power cable to WN-AC1600DGR, press "4" on the serial
console and enter the U-Boot console
4. execute "tftpboot" command on the console and download initramfs
image from the TFTP server
5. execute "bootm" command and boot OpenWrt
6. On initramfs image, download the sysupgrade image to the device
and perform sysupgrade with it
7. Wait ~150 seconds to complete flashing

This commit also removes unnecessary "qca,no-eeprom" property from
the ath10k wifi node.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
5 years ago
Paul Wassi 212892ce70 ath79: fix port order on TL-WR841ND-v7
The switch ports are seen one to one on the case.
Also remove unneeded secondary port numbers in this
case statement.

Signed-off-by: Paul Wassi <p.wassi@gmx.at>
5 years ago
Paul Wassi ff541c5ca2 ath79: rename TL-WR740ND-v4 to TL-WR740N-v4
Give the device the same name it had in ar71xx.

Signed-off-by: Paul Wassi <p.wassi@gmx.at>
5 years ago
Paul Wassi da1107f8a5 ath79: fix TL-WR741ND-v4 switch port order
Fix the switch port order for proper display on high
level interfaces.

Signed-off-by: Paul Wassi <p.wassi@gmx.at>
5 years ago
David Bauer 0c24b363a6 ath79: add support for Xiaomi Mi Router 4Q
Hardware
--------
CPU:   Qualcomm Atheros QCA9561
RAM:   64M DDR2
FLASH: 16M SPI-NOR
ETH:   1x WAN - 2x LAN
WiFi:  QCA9561 3T3R
BTN:   1x Reset - 1x WPS
LED:   1x Blue - 1x Red - 1x Yellow
UART:  TX - GND - RX - VCC (From ethernet port)
       115200n8 - 3.3V

Installation
------------
1. Connect to the device via UART.

2. Interrupt the U-Boot on power-on by pressing enter when prompted.

3. Connect you computer to one of the routers LAN ports.
   Assign yourself the IP 192.168.31.10/24.
   Copy the OpenWRT initramfs image to a tftp server root directory.
   Rename the image to 'x4q.bin'.

4. Load the initramfs image to the router by executing following command
   in U-Boot. The image will boot afterwards.

   > tftpboot 0x81000000 x4q.bin; bootm

5. SCP the sysupgrade-image into '/tmp'.
   Remember to assign yourself an IP in 192.168.1.0/24 for this step!

6. Install OpenWRT permanently by executing

   > sysupgrade -n /tmp/<OpenWRT-sysupgrade-image>

Signed-off-by: David Bauer <mail@david-bauer.net>
5 years ago
Oldřich Jedlička 12310f05b7 ath79: add support for TP-LINK Archer C7 v4
TP-Link Archer C7 v4 is a dual-band AC1750 router, based on the
Qualcomm/Atheros QCA9561 SoC + QCA9880.

Specification:

- 775/650/258 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 3T3R 5 GHz
- 5x 10/100/1000 Mbps Ethernet
- 7x LED, 2x button
- UART header on PCB

Flash instruction:
1. Upload openwrt-ath79-generic-tplink_archer-c7-v4-squashfs-factory.bin
   via Web interface

Flash instruction using TFTP recovery:
1. Set PC to fixed ip address 192.168.0.66
2. Download openwrt-ath79-generic-tplink_archer-c7-v4-squashfs-factory.bin
   and rename it to ArcherC7v4_tp_recovery.bin
3. Start a tftp server with the file tp_recovery.bin in its root directory
4. Turn off the router
5. Press and hold Reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time
   the firmware should be transferred from the tftp server
8. Wait ~30 second to complete recovery.

Signed-off-by: Oldřich Jedlička <oldium.pro@gmail.com>
5 years ago
Skirmantas Lauzikas 9c01273e5e ath79: add support for TP-Link Archer C2 V3 (AC900)
This commit adds support for the TP-link Archer C2 V3 (AC900).

Specifications:

 - CPU: QCA9563 750Mhz
 - Ram: 64MB (DDR2)
 - Flash: 8MB (SPI NOR)
 - Ethernet: 5x 10/100/1000
 - Wifi: QCA9563 bgn + QCA9887 an+ac
 - 9x Leds, 2x buttons

Flash instructions:

Upload openwrt-ath79-generic-tplink_archer-c2-v3-squashfs-factory.bin
via the router Web interface and flash as normal firmware update.

Signed-off-by: Skirmantas Lauzikas <skirmantas.lauzikas@blackraven.lt>
[reorder entries, fix trailing whitespace in dts, add firmware partition
 compatible string, remove led default off states, use default on state
 for system led, reuse tplink-safeloader-uimage image build recipe, squash
 with dynamic partitioning commit, reword commit message, add
 installation instructions]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
5 years ago
Django Armstrong 1c2f7b5115 ath79: add support for Devolo WiFi Pro 1750e
Hardware
--------
CPU:   Qualcomm Atheros QCA9558
RAM:   128M DDR2
FLASH: 16MiB
ETH:   1x Atheros AR8035 (PoE in)
       1x Atheros AR8033
WiFi2: QCA9558 3T3R (SiGE SE2565T 2.4 GHz power amp x3)
WiFi5: QCA9880 3T3R (Skyworks 5003L1 5 GHz power amp x3)
BTN:   1x Reset
       1x WPS
       1x USB eject
LED:   1x LED blue
       1x LED red
BEEP:  1x GPIO attached piezo beeper
UART:  3.3V GND TX RX (115200-N-8) (3.3V is pin closest to rear ports)
       Dupont 4 pin header
       Rear RJ45 serial port non-functional
USB:   1x v2.0

Installation
------------
Make sure you set a password for the root user as prompted on first
setup!

1. Upload OpenWRT sysupgrade image via SSH to the device.
Use /tmp as the destination folder on the device.
User is root, password previously set in the web interface.

2. Install OpenWRT with

> sysupgrade -n -F /tmp/<openwrt-image-name>

Signed-off-by: Django Armstrong <iamdjango@hotmail.com>
5 years ago
Sebastian Kemper 69dfdda157 ath79: fix port order for dir 825-c1 and 835-a1
LAN ports 1 and 4 and 2 and 3 are interchanged. Fix this in 02_network
so the ports show up in the correct order in luci.

The correct ucidef_add_switch line is already present. This commit moves
the blocks around to keep alphabetical order.

Signed-off-by: Sebastian Kemper <sebastian_ml@gmx.net>
5 years ago
David Bauer c8115167f9 ath79: add support for devolo WiFi pro 1200i
Hardware
--------
CPU:   Qualcomm Atheros QCA9558
RAM:   128M DDR2
FLASH: 16MiB
ETH:   1x Atheros AR8035 (PoE in)
WiFi2: QCA9558 2T2R
WiFi5: QCA9880 2T2R
BTN:   1x Reset
LED:   1x LED blue
       1x LED red
BEEP:  1x GPIO attached piezo beeper
UART:  3.3V GND TX RX (115200-N-8) (3.3V is square pad)
       Header is located next to reset-button

Installation
------------
Make sure you set a password for the root user as prompted on first
setup!

1. Upload OpenWRT sysupgrade image via SSH to the device.
Use /tmp as the destination folder on the device.
User is root, password the one set in the web interface.

2. Install OpenWRT with

> sysupgrade -n -F /tmp/<openwrt-image-name>

Signed-off-by: David Bauer <mail@david-bauer.net>
6 years ago
David Bauer 8d68be8057 ath79: add support for devolo WiFi pro 1750i
Hardware
--------
CPU:   Qualcomm Atheros QCA9558
RAM:   128M DDR2
FLASH: 16MiB
ETH:   1x Atheros AR8035 (PoE in)
WiFi2: QCA9558 3T3R
WiFi5: QCA9880 3T3R
BTN:   1x Reset
LED:   1x LED blue
       1x LED red
BEEP:  1x GPIO attached piezo beeper
UART:  3.3V GND TX RX (115200-N-8) (3.3V is square pad)
       Header is located next to reset-button

Installation
------------
Make sure you set a password for the root user as prompted on first
setup!

1. Upload OpenWRT sysupgrade image via SSH to the device.
Use /tmp as the destination folder on the device.
User is root, password the one set in the web interface.

2. Install OpenWRT with

> sysupgrade -n -F /tmp/<openwrt-image-name>

Signed-off-by: David Bauer <mail@david-bauer.net>
6 years ago
Paul Wassi eb1887be93 ath79: merge cases in 02_network
Merge some duplicate cases in /etc/board.d/02_network

Signed-off-by: Paul Wassi <p.wassi@gmx.at>
6 years ago
Christoph Krapp 59b99e1924 ath79: align GL-AR750S boardname to other GL.iNet devices
As the official device name is GL-AR750S, rename the board accordingly.

Signed-off-by: Christoph Krapp <achterin@googlemail.com>
6 years ago
Georgi Vlaev d03aae1a09 ath79: add support for TP-Link Archer C6 v2
This patch adds support for TP-Link Archer C6 v2 (EU)

Hardware specification:
- SOC: Qualcomm QCA9563 @ 775MHz
- Flash: GigaDevice GD25Q64CSIG (8MiB)
- RAM: Zentel A3R1GE40JBF (128 MiB DDR2)
- Ethernet: Qualcomm QCA8337N: 4x 1Gbps LAN + 1x 1Gbps WAN
- Wireless:
  - 2.4GHz (bgn) QCA9563 integrated (3x3)
  - 5GHz (ac) Qualcomm QCA9886 (2x2)
- Button: 1x power, 1x reset, 1x wps
- LED: 6x LEDs: power, wlan2g, wlan5g, lan, wan, wps
- UART: There's no UART header on the board

Flash instructions:

Upload
openwrt-ath79-generic-tplink_archer-c6-v2-squashfs-factory.bin
via the router Web interface.

Flash instruction using tftp recovery:

1. Connect the computer to one of the LAN ports of the router
2. Set the computer IP to 192.168.0.66
3. Start a tftp server with the OpenWrt factory image in the
   tftp root directory renamed to ArcherC6v2_tp_recovery.bin.
4. Connect power cable to router, press and hold the reset
   button and turn the router on
5. Keep the reset button pressed until the WPS LED lights up
6. Wait ~150 seconds to complete flashing

According to the GPL source the non-EU variant has different
GPIOs assigned to some of the LEDs and buttons. The flash
layout might be different as well. The wikidevi entry for
Archer A6/C6 assumes they are identical.

Signed-off-by: Georgi Vlaev <georgi.vlaev@gmail.com>
6 years ago
Guan-Hong Lin 9ebb44aef4 ath79: add support for EnGenius EWS511AP
EnGenius EWS511AP is a wireless managed wall AP with PoE support,
based on Qualcomm/Atheros QCA9531(Honeybee) + QCA9887.

Short specification:

- 128MB of RAM
- 16 MB of SPI FLASH
- 2T2R 2.4 GHz (QCA9531), 802.11b/g/n
- 1T1R 5 GHz (QCA9887), 802.11ac/n/a
- 2x 10/100 Mbps Ethernet (one port with PoE support)
- 1x Power LED, 2x LAN LEDs, 1x WLAN 2.4G LED, 1x WLAN 5G LED
- 1x RESET button
- built-in watchdog chipset

Flash instruction:

From EnGenius firmware to OpenWrt firmware:

Original firmware is based on QSDK.
Use sysupgrade firmware directly in vendor GUI.
Reset to factory default is necessary.

From OpenWrt firmware to EnGenius firmware:

1. Setup a TFTP server on your computer and configure static IP to 192.168.99.8
   Put the OpenWrt firmware in the root directory on your computer.
2. Power up EWS511AP. Press 4 and then press any key to enter u-boot.
3. Download OpenWrt firmware
   (ath)> tftpboot 0x80060000 ${dir}"openwrt-ath79-generic-engenius_ews511ap-squashfs-sysupgrade.bin"
4. Flash the firmware
   (ath)> erase 0x9f060000 +f50000
   (ath)> cp.b $fileaddr 0x9f060000 $filesize
5. Reboot
   (ath)> reset

Signed-off-by: Guan-Hong Lin <GH.Lin@senao.com>
6 years ago
Paul Wassi 6e78d546d1 ath79: fix boardname of GL.iNet GL-AR300M
This device is called GL-AR300M, therefore rename the board(s)
to 'gl-ar300m-nor' and 'gl-ar300m-nand'

Signed-off-by: Paul Wassi <p.wassi@gmx.at>
[change boardname in uboot envtools as well, don't use wildcards for
boardname]
Signed-off-by: Mathias Kresin <dev@kresin.me>
6 years ago
Paul Wassi cdbf2de777 ath79: Add support for TP-Link WR810N
Device specifications given in b23b0fb28b

Signed-off-by: Paul Wassi <p.wassi@gmx.at>
6 years ago
Paul Wassi 8ba76d6e74 ath79: fix boardname of GL.iNet GL-AR150
This device is called GL-AR150, therefore rename the board
to 'gl-ar150'

Signed-off-by: Paul Wassi <p.wassi@gmx.at>
6 years ago
INAGAKI Hiroshi caf306ce91 ath79: add support for ELECOM WRC-1750GHBK2-I/C
ELECOM WRC-1750GHBK2-I/WRC-1750GHBK2-C are 2.4/5 GHz band 11ac
routers, based on Qualcomm Atheros QCA9563.

This commit also includes small fix; use "0x0x03000101" as pll_1000
instead of "0x03000000".

Specification:

- SoC:      Qualcom Atheros QCA9563
- RAM:      128 MB (DDR2)
- Flash:    16 MB (SPI-NOR)
- WLAN:     2.4/5 GHz
  - 2.4 GHz: 2T2R (SoC internal)
  - 5 GHz:   3T3R (QCA9880)
- Ethernet: 10/100/1000 Mbps
- LED/key:  4x/3x (2x buttons, 1x slide-switch)
- UART:     through-hole on PCB
  - Vcc, RX, GND, TX from switch (QCA8337N) side
  - 115200n8

Flash instruction using factory image:

1. Boot WRC-1750GHBK2-I/C normaly
2. Access to "http://192.168.2.1/" and open firmware upgrade page
("ファームウェア更新 手動更新(アップデート)")
3. Select the OpenWrt factory image and click apply ("適用") button
to perform firmware update
4. On the (initramfs) factory image, perform sysupgrade with
squashfs-sysupgrade image
5. Wait ~150 seconds to complete flashing

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
6 years ago
Antonio Silverio 9601d94138 ath79: add support for TP-Link TL-WR841N/ND v8
CPU: Atheros AR9341 535MHz
RAM: 32MB
FLASH: 4MiB
PORTS: 4 Port 100/10 Switch, 1 Port 100/10 Wan
WiFi: Atheros AR9341 2x2:2 bgn
LED: Power (static on), LAN (controlled by Switch), WAN, SYS, WiFi, RFKill
BTN: WPS, WiFi, Reset

Installation:
Upload the factory image via the vendor-GUI.

Signed-off-by: Antonio Silverio <menion@gmail.com>
[resolve merge conflicts, squash commits, fix commit title, remove
default default off led properties, mark sysupgrade image compatible
with the ar71xx version of the board, drop blank lines from dts]
Signed-off-by: Mathias Kresin <dev@kresin.me>
6 years ago
Christoph Krapp af28d8a539 ath79: add support for GL.iNet GL-AR750S
Right now this patch adds nor image generation only. NAND image
generation is not supportet at the moment.

Furtheremore support for the MicroSD port is not implemented as of now.

Specification:
- SOC: QCA9563 (775MHz)
- Flash: 16 MiB (W25Q128FVSG)
- RAM: 128 MiB DDR2
- Ethernet: 2x 1Gbps LAN + 1x 1Gbps WAN
- Wireless: 2.4GHz (bgn) and 5GHz (ac)
- USB: 1x USB 2.0 port
- Button: 1x switch button, 1x reset button
- LED: 3x LEDS (green)
  - Another LED can be accessed on GPIO 7 if soldered

Flash instruction:
- Set static ip to 192.168.1.2
- Unplug the power cord
- Hold reset button
- Plug power back in
- Right led will flash 5 times
- Release reset button
- Browse to 192.168.1.1
- Choose sysupgrade image in NOR-flash section
- Press "update nor firmware"
- After successful transfer unplug network cable before device restarts

Signed-off-by: Christoph Krapp <achterin@googlemail.com>
[resolve merge conflicts, rename buttons, use switch input type for mode
switch]
Signed-off-by: Mathias Kresin <dev@kresin.me>
6 years ago
Weijie Gao abc7ed2c58 ath79: add support for D-Link DIR-859 A1
Hardware spec of DIR-859 A1:
SoC: QCA9563
DRAM: 64MB DDR2
Flash: 16MB SPI-NOR
Switch: QCA8337N
WiFi 5.8GHz: QCA9880

USB is supported on the PCB but not connected.

Flash instructions:

1. Upgrade the factory.bin through the factory web interface or the u-boot
   failsafe interface.
   The firmware will boot up correctly for the first time.
   Do not power off the device after OpenWrt has booted. Otherwise the u-boot
   will enter failsafe mode as the checksum of the firmware has been changed.
2. Upgrade the sysupgrade.bin in OpenWrt.
   After upgrading completes the u-boot won't complain about the firmware
   checksum and it's OK to use now.
3. If you powered off the device before upgrading the sysupgrade.bin, just
   upgrade the factory.bin through the u-boot failsafe interface and then goto
   step 2.

Signed-off-by: Weijie Gao <hackpascal@gmail.com>
[squash commits, use common seama recipes, sync factory image recipe
with ramips version]
Signed-off-by: Mathias Kresin <dev@kresin.me>
6 years ago
Eduardo Barros 335c69fbb2 ath79: Fix wrong TL-WR740N v4 switch port order
Fix the switch port order to have the correct order in LuCI.

Fixes: FS#1469

Signed-off-by: Eduardo Barros <geadas@gmail.com>
[trim commit title, add a proper commit message, add fixes tag, keep
alphabetical order of the blocks]
Signed-off-by: Mathias Kresin <dev@kresin.me>
6 years ago
David Bauer e67da34431 ath79: add support for devolo WiFi pro 1750c
Hardware
--------
CPU:   Qualcomm Atheros QCA9558
RAM:   128M DDR2
FLASH: 16MiB
ETH:   1x Atheros AR8035 (PoE in)
WiFi2: QCA9558 3T3R
WiFi5: QCA9880 3T3R
BTN:   1x Reset
LED:   1x LED blue
       1x LED red
BEEP:  1x GPIO attached piezo beeper
UART:  3.3V GND TX RX (115200-N-8) (3.3V is square pad)
       Header is located next to reset-button

There is also a Micro-B USB-port present but this only seems to be a
dummy as the circuit next to it is not present (at least in my unit).

It is also not mentioned in the devolo manual.

Installation
------------
Make sure you set a password for the root user as prompted on first
setup!

1. Upload OpenWRT sysupgrade image via SSH to the device.
Use /tmp as the destination folder on the device.
User is root, password the one set in the web interface.

2. Install OpenWRT with

> sysupgrade -n -F /tmp/<openwrt-image-name>

Signed-off-by: David Bauer <mail@david-bauer.net>
6 years ago
David Bauer 1724d4e9ed ath79: add support for devolo WiFi pro 1200e
Hardware
--------
CPU:   Qualcomm Atheros QCA9558
RAM:   128M DDR2
FLASH: 16MiB
ETH:   1x Atheros AR8035 (PoE in)
       1x Atheros AR8033
WiFi2: QCA9558 2T2R
WiFi5: QCA9880 2T2R
BTN:   1x Reset
LED:   1x LED blue
       1x LED red
BEEP:  1x GPIO attached piezo beeper
UART:  3.3V GND TX RX (115200-N-8) (3.3V is square pad)
       Header is located next to reset-button

Installation
------------
Make sure you set a password for the root user as prompted on first
setup!

1. Upload OpenWRT sysupgrade image via SSH to the device.
Use /tmp as the destination folder on the device.
User is root, password the one set in the web interface.

2. Install OpenWRT with

> sysupgrade -n -F /tmp/<openwrt-image-name>

Signed-off-by: David Bauer <mail@david-bauer.net>
6 years ago
TOCK Chiu 8471944325 ath79: add support for TP-Link Archer C7 v5
This commit adds support for TP-Link Archer C7 v5, leveraging most effort
from commit ea9baee and 1e4ee63. Archer C7 v5 is identical to Archer A7 v5
but with a different flash layout.

Specification:
-   QCA9563 SoC (750 MHz)
-   128 MiB of RAM (DDR2)
-   16 MiB of flash (SPI)
-   5x 1 Gbps Ethernet (1x WAN + 4x LAN)
-   2.4GHz (bgn) SoC internal + 5GHz (ac) QCA9880
-   10x LED, 2x button
-   UART header on PCB

Flash instructions:
1.  Upload openwrt-ath79-generic-tplink_archer-c7-v5-squashfs-factory.bin
    via web interface.

Flash instructions using TFTP recovery:
1.  Plug PC to one of the LAN ports
2.  Set PC to fixed IP address 192.168.0.66
3.  Rename the factory image to ArcherC7v5_tp_recovery.bin and place it in
    TFTP root directory
4.  Turn on the router with the reset button pressed for about 15 secs
5.  Release the button and wait about 150 secs to complete flashing

Signed-off-by: TOCK Chiu <tock.chiu@gmail.com>
6 years ago
INAGAKI Hiroshi c566439c9b ath79: add support for NEC Aterm WG800HP
NEC Aterm WG800HP is a 2.4/5 GHz band 11ac router, based on Qualcomm
Atheros QCA9563.

Specification:

- Qualcomm Atheros QCA9563
- 64 MB of RAM (DDR2)
- 8 MB of Flash (SPI-NOR)
- 2.4/5 GHz wifi
  - 2.4 GHz: 2T2R (SoC internal)
  - 5 GHz: 1T1R (QCA9887)
- 4x 10/100/1000 Mbps Ethernet
- 8x LEDs, 3x keys (2x buttons, 1x slide-switch)
- UART through-hole on PCB (J2)
  - Vcc, GND, NC, TX, RX from SoC side
  - 115200n8

Flash instruction using factory image:

1. Connect the computer to the LAN port on WG800HP
2. Connect power cable to WG800HP and turn on it
3. Access to "http://192.168.10.1/" and open firmware update page
("ファームウェア更新")
4. Select the OpenWrt factory image and click update ("更新") button
5. Wait ~150 seconds to complete flashing

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
6 years ago
Karl-Felix Glatzer 1e4ee63cc8 ath79: add support for TP-Link Archer A7
This patch adds support for TP-Link Archer A7

Specification:
- SOC: QCA9563
- Flash: 16 MiB (SPI)
- RAM: 128 MiB (DDR2)
- Ethernet: 4x 1Gbps LAN + 1x 1Gbps WAN
- Wireless:
  - 2.4GHz (bgn) SoC internal
  - 5GHz (ac) QCA988x
- USB: 1x USB 2.0 port
- Button: 1x power, 1x reset, 1x wps
- LED: 10x LEDs
- UART: holes in PCB
  - Vcc, GND, RX, TX from ethernet port side
  - 115200n8

Flash instructions:

Upload openwrt-ath79-generic-tplink_archer-a7-v5-squashfs-factory.bin
via the Webinterface.

Flash instruction using tftp recovery:

1. Connect the computer to one of the LAN ports of the Archer A7
2. Set the computer IP to 192.168.0.66
3. Start a tftp server with the OpenWrt factory image in the tftp
   root directory renamed to ArcherC7v5_tp_recovery.bin
2. Connect power cable to Archer A7, press and hold the reset button
   and turn the router on
3. Keep the reset button pressed for ~5 seconds
4. Wait ~150 seconds to complete flashing

Changes since first revision:

  - Flash instructions using stock image webinterface
  - Changed "Version 5" in model string to "v5"
  - Split DTS file in qca9563_tplink_archer-x7-v5.dtsi
    and qca9563_tplink_archer-a7-v5.dts
  - Firmware image is now build with dynamic partitioning
  - Default to ath10k-ct

Changes since second revision:
  - Changed uboot@0 to uboot@20000 in DTS file
  - Fixed ordering issue in board led script
  - Specify firmware partition format in DTS file
  - Rebased Makefile device definition on common
    Device/tplink-safeloader-uimage definition
  - Merged switch section in network script
    (same configuration as tplink,tl-wdr3600
    and tplink,tl-wdr4300)

Signed-off-by: Karl-Felix Glatzer <karl.glatzer@gmx.de>
6 years ago
Sebastian Kemper 6c3c4436ee ath79: add d-link dir-825-c1 and dir-835-a1
This commit ports both dir-825-c1 and dir-835-a1 from ar71xx to ath79.
They're pretty much identical, except dir-835-a1 has less LEDs.

The routers come with 128 MByte of RAM and 16 MBytes of flash and sport
2.4GHz and 5.0GHz wireless. Both routers have entries already in
OpenWrt's TOH. Please check there for more information on these
antiquities.

https://openwrt.org/toh/hwdata/d-link/d-link_dir-825_c1
https://openwrt.org/toh/hwdata/d-link/d-link_dir-835_a1

Installation:

1. Connect to the web interface of the vendor firmware (usually
   listening on 192.168.0.1).
2. Go to "Tools", then "Firmware".
3. In the "Firmware Upgrade" box click "Browse".
4. Select the OpenWrt factory image for your router.
5. Click "Upload", confirm the popups if you agree to flash the file you
   selected.
6. Wait for firmware upgrade to complete. It takes about 5 minutes.

Run-tested on dir-825-c1. dir-835-a1 should work as well, but I don't
have this router so I can't confirm.

Signed-off-by: Sebastian Kemper <sebastian_ml@gmx.net>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [trivial changes]
6 years ago
Marcin Jurkowski 3c3eaa57d9 ath79: add support for TP-Link TL-WR842N/ND v1 router
This ports support for TP-Link TL-WR842N/ND v1 from ar71xx.

CPU: Atheros AR7241 400 MHz
RAM: 32 MiB
FLASH: 8 MiB
PORTS: 4 Port 100/10 Switch, 1 Port 100/10 Wan
WiFi: Atheros AR9287
LED: SYS, WiFi, LAN, WAN, 3G, QSS
BTN: WiFi, Reset/WPS

AR71xx target used "tl-mr3420" as board id so force flag is needed
if upgrading from old target.

Signed-off-by: Marcin Jurkowski <marcin1j@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [trivial cleanup]
6 years ago
INAGAKI Hiroshi 3358cae523 ath79: add support for I-O DATA WN-AG300DGR
I-O DATA WN-AG300DGR is a 2T2R 2.4/5 GHz 11n router, based on Atheros
AR1022.

WN-AG300DGR does not have an LED to indicates power or system status,
I set "router" LED as OpenWrt status LED.

There is no eeprom data for 5 GHz wlan in "art" partition.

Specification:

- Atheros AR1022
- 64 MB of RAM (DDR2)
- 8 MB of Flash (SPI-NOR)
- 2T2R 2.4/5GHz wifi
  - 2.4 GHz: SoC internal
  - 5 GHz: Atheros AR93x2
- 5x 10/100/1000 Mbps Ethernet
- 6x LEDs, 6x keys (4x buttons, 1x slide switch)
- 1x USB 2.0 Type-A
- UART through-hole on PCB
  - Vcc, GND, TX, RX from ethernet port side
  - 115200n8

Flash instruction using factory image:

1. Connect the computer to the LAN port on WN-AG300DGR
2. Connect power cable to WN-AG300DGR and turn it
3. Access to "http://192.168.0.1/" and open firmware update page
("ファームウェア")
4. Select the OpenWrt factory image and click update ("更新") button
5. Wait ~150 seconds to complete flashing

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
6 years ago
Chuanhong Guo 9dd7147f6b ath79: add support for Winchannel WB2000
WB2000 is a dual-band 11N AP using AR9344.
The factory firmware used the original DB120 partition table
with a small kernel partition at the end of firmware and the
kernel will easily get oversized in the future. Since it has
to be flashed using UART I also swapped kernel/rootfs and
changed the default load address.

Specification:

- SoC: Atheros AR9344
- RAM: 128 MB
- Flash: 16 MB
- Ethernet: 10/100/1000 Mbps (Atheros AR8035)
- 2x USB 2.0
- WIFI: AR9344(2G) + AR9382(5G)
- RTC: DS1338

Known issue:
5G ath9k led doesn't work due to commit ccab68f.

Flash instruction:
Set up a TFTP server on your computer and configure static IP.
Connect UART (J11 TX/GND/RX) and press any key to enter U-boot
shell.
1. Change the default boot command:
   setenv bootcmd 'bootm 0x9f050000 || bootm 0x9fd50000'
   saveenv
2. Set your router ipaddr and server ipaddr. e.g.:
   setenv ipaddr 192.168.1.1
   setenv serverip 192.168.1.50
3. Load and flash the firmware:
   tftp 0x80060000 fw.bin
   erase 0x9f050000 +$filesize
   cp.b $fileaddr 0x9f050000 $filesize
4. Reset your router:
   reset

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
[Drop the i2c node unit address. Move the ath9k-leds node out of the spi
node, it doesn't belong there. Add the #gpio-cells property to the pci
wifi node. All fix dtc compiler warnings]
Signed-off-by: Mathias Kresin <dev@kresin.me>

merge
6 years ago
Russell Senior 73127a878d ath79: add support for Ubiquiti AirRouter
Indoor low-power router with 2.4 GHz radio

CPU:    Atheros AR7241 rev 1
RAM:    32 MB
Flash:  8 MB NOR SPI
Switch: Atheros AR7240
Ports:  1x WAN, 4x LAN 10/100 Ethernet
WLAN:   Atheros AR9285 (2.4 GHz)
USB:    1x USB2 host port

Note: Ethernet WAN/LAN port naming is reversed from ar71xx.
WAN is eth0; LAN is eth1.1.

UART settings: 115200, 8N1

                LEDs
        +--------------------------
        |
        |
        |
        |
        |
        |
        |
        |
    VCC | x x
     RX | * x
        | x x
        | x x
     TX | * x
    GND | * x
        |
        |
        |
        |
        +--------------------------
                ETHERNET PORTS

Installation from Ubiquiti firmware, is as for other ubnt-xm AirOs devices.

Signed-off-by: Russell Senior <russell@personaltelco.net>
6 years ago
Rosy Song 31469aebd4 ath79: add support for ROSINSON WR818 board
This commit adds support for the ROSINSON WR818 WiFi-Router

SoC:    Qualcomm Atheros QCA9563,
FLASH:  Winbond W25Q128FV 16MBytes,
WiFi:   QCA9563 b/g/n 3x3 450Mbit/s,
USB:    1x USB 2.0 Type A, 1x USB2.0 Type C,
IN:     WPS/Reset button GPIO1,
OUT:    Power LED red, Internet LED red, WLAN LED red,
        LAN1 LED red, LAN2 LED red, System LED red,
UART:   RX-GPIO18, TX-GPIO22,

Tested and working:
    - Ethernet (LAN + WAN)
    - WiFi
    - OpenWRT sysupgrade
    - Button
    - LEDs

Installation of OpenWRT from vendor firmware:
    - Connect to the Web-interface at http://192.168.1.1
    - Go to "Administration" -> "Firmware Upgrade"
    - Upload the OpenWrt sysupgrade image

Signed-off-by: Rosy Song <rosysong@rosinson.com>
6 years ago
Mathias Kresin 68d77241cd ath79: rename glinet x750
The boardname is gl-x750 and is already used for the led names.

Signed-off-by: Mathias Kresin <dev@kresin.me>
6 years ago
Mathias Kresin f4abc962ec ath79: fix shebang
The shebang was accidentally changed with 9989fd5154 ("ath79: add
support for GL-iNet GL-X750").

Signed-off-by: Mathias Kresin <dev@kresin.me>
6 years ago