ath79: add support for I-O DATA WN-AG300DGR
I-O DATA WN-AG300DGR is a 2T2R 2.4/5 GHz 11n router, based on Atheros AR1022. WN-AG300DGR does not have an LED to indicates power or system status, I set "router" LED as OpenWrt status LED. There is no eeprom data for 5 GHz wlan in "art" partition. Specification: - Atheros AR1022 - 64 MB of RAM (DDR2) - 8 MB of Flash (SPI-NOR) - 2T2R 2.4/5GHz wifi - 2.4 GHz: SoC internal - 5 GHz: Atheros AR93x2 - 5x 10/100/1000 Mbps Ethernet - 6x LEDs, 6x keys (4x buttons, 1x slide switch) - 1x USB 2.0 Type-A - UART through-hole on PCB - Vcc, GND, TX, RX from ethernet port side - 115200n8 Flash instruction using factory image: 1. Connect the computer to the LAN port on WN-AG300DGR 2. Connect power cable to WN-AG300DGR and turn it 3. Access to "http://192.168.0.1/" and open firmware update page ("ファームウェア") 4. Select the OpenWrt factory image and click update ("更新") button 5. Wait ~150 seconds to complete flashing Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>v19.07.3_mercusys_ac12_duma
INAGAKI Hiroshi
6 years ago
committed by
Mathias Kresin
parent
9dd7147f6b
commit
3358cae523
@ -0,0 +1,222 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
/dts-v1/;
|
||||
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
|
||||
#include "ar9344.dtsi"
|
||||
|
||||
/ {
|
||||
compatible = "iodata,wn-ag300dgr", "qca,ar9344";
|
||||
model = "I-O DATA WN-AG300DGR";
|
||||
|
||||
aliases {
|
||||
led-boot = &router;
|
||||
led-failsafe = &router;
|
||||
led-running = &router;
|
||||
led-upgrade = &router;
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
router: router {
|
||||
label = "wn-ag300dgr:green:router";
|
||||
gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
|
||||
default-state = "on";
|
||||
};
|
||||
|
||||
children {
|
||||
label = "wn-ag300dgr:green:children";
|
||||
gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
|
||||
default-state = "off";
|
||||
};
|
||||
|
||||
eco {
|
||||
label = "wn-ag300dgr:green:eco";
|
||||
gpios = <&gpio 3 GPIO_ACTIVE_LOW>;
|
||||
default-state = "off";
|
||||
};
|
||||
|
||||
notification {
|
||||
label = "wn-ag300dgr:amber:notification";
|
||||
gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
|
||||
default-state = "off";
|
||||
};
|
||||
|
||||
wlan2g {
|
||||
label = "wn-ag300dgr:green:wlan2g";
|
||||
gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
|
||||
default-state = "off";
|
||||
linux,default-trigger = "phy0tpt";
|
||||
};
|
||||
|
||||
wlan5g {
|
||||
label = "wn-ag300dgr:green:wlan5g";
|
||||
gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
|
||||
default-state = "off";
|
||||
linux,default-trigger = "phy1tpt";
|
||||
};
|
||||
};
|
||||
|
||||
keys {
|
||||
compatible = "gpio-keys-polled";
|
||||
poll-interval = <20>;
|
||||
|
||||
eco {
|
||||
label = "eco";
|
||||
gpios = <&gpio 0 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <BTN_1>;
|
||||
debounce-interval = <60>;
|
||||
};
|
||||
|
||||
router {
|
||||
label = "router";
|
||||
gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <BTN_0>;
|
||||
linux,input-type = <EV_SW>;
|
||||
debounce-interval = <60>;
|
||||
};
|
||||
|
||||
auto {
|
||||
label = "auto";
|
||||
gpios = <&gpio 4 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <BTN_0>;
|
||||
linux,input-type = <EV_SW>;
|
||||
debounce-interval = <60>;
|
||||
};
|
||||
|
||||
wps {
|
||||
label = "wps";
|
||||
gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_WPS_BUTTON>;
|
||||
debounce-interval = <60>;
|
||||
};
|
||||
|
||||
reset {
|
||||
label = "reset";
|
||||
gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_RESTART>;
|
||||
debounce-interval = <60>;
|
||||
};
|
||||
|
||||
children {
|
||||
label = "children";
|
||||
gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <BTN_1>;
|
||||
debounce-interval = <60>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&ref {
|
||||
clock-frequency = <25000000>;
|
||||
};
|
||||
|
||||
&spi {
|
||||
num-cs = <1>;
|
||||
status = "okay";
|
||||
|
||||
flash@0 {
|
||||
compatible = "jedec,spi-nor";
|
||||
reg = <0>;
|
||||
spi-max-frequency = <25000000>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "u-boot";
|
||||
reg = <0x000000 0x030000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@30000 {
|
||||
label = "u-boot-env";
|
||||
reg = <0x030000 0x010000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@40000 {
|
||||
compatible = "denx,uimage";
|
||||
label = "firmware";
|
||||
reg = <0x040000 0xf10000>;
|
||||
};
|
||||
|
||||
partition@f50000 {
|
||||
label = "manufacture";
|
||||
reg = <0xf50000 0x40000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@f90000 {
|
||||
label = "backup";
|
||||
reg = <0xf90000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@fa0000 {
|
||||
label = "storage";
|
||||
reg = <0xfa0000 0x50000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@ff0000 {
|
||||
label = "art";
|
||||
reg = <0xff0000 0x010000>;
|
||||
read-only;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&mdio0 {
|
||||
status = "okay";
|
||||
|
||||
phy0: ethernet-phy@0 {
|
||||
reg = <0>;
|
||||
phy-mode = "rgmii";
|
||||
|
||||
qca,ar8327-initvals = <
|
||||
0x04 0x07a00000 /* PORT0 PAD MODE CTRL */
|
||||
0x7c 0x000000fe /* PORT0_STATUS */
|
||||
>;
|
||||
};
|
||||
};
|
||||
|
||||
ð0 {
|
||||
status = "okay";
|
||||
|
||||
pll-data = <0x06000000 0x00000101 0x00001616>;
|
||||
|
||||
phy-mode = "rgmii";
|
||||
phy-handle = <&phy0>;
|
||||
|
||||
gmac-config {
|
||||
device = <&gmac>;
|
||||
rgmii-gmac0 = <1>;
|
||||
};
|
||||
};
|
||||
|
||||
&pcie {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&uart {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usb {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usb_phy {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&wmac {
|
||||
status = "okay";
|
||||
qca,no-eeprom;
|
||||
};
|
||||
Loading…
Reference in New Issue