ath79: add support for devolo WiFi pro 1200e
Hardware -------- CPU: Qualcomm Atheros QCA9558 RAM: 128M DDR2 FLASH: 16MiB ETH: 1x Atheros AR8035 (PoE in) 1x Atheros AR8033 WiFi2: QCA9558 2T2R WiFi5: QCA9880 2T2R BTN: 1x Reset LED: 1x LED blue 1x LED red BEEP: 1x GPIO attached piezo beeper UART: 3.3V GND TX RX (115200-N-8) (3.3V is square pad) Header is located next to reset-button Installation ------------ Make sure you set a password for the root user as prompted on first setup! 1. Upload OpenWRT sysupgrade image via SSH to the device. Use /tmp as the destination folder on the device. User is root, password the one set in the web interface. 2. Install OpenWRT with > sysupgrade -n -F /tmp/<openwrt-image-name> Signed-off-by: David Bauer <mail@david-bauer.net>v19.07.3_mercusys_ac12_duma
parent
8471944325
commit
1724d4e9ed
@ -0,0 +1,47 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
/dts-v1/;
|
||||
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
|
||||
#include "qca9558_devolo_dvl1xxx.dtsi"
|
||||
|
||||
/ {
|
||||
compatible = "devolo,dvl1200e", "qca,qca9557";
|
||||
model = "devolo WiFi pro 1200e";
|
||||
|
||||
aliases {
|
||||
led-boot = &status_blue;
|
||||
led-failsafe = &status_red;
|
||||
led-running = &status_blue;
|
||||
led-upgrade = &status_red;
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
status_blue: status_blue {
|
||||
label = "dvl1200e:blue:status";
|
||||
gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
|
||||
default-state = "on";
|
||||
};
|
||||
|
||||
status_red: status_red {
|
||||
label = "dvl1200e:red:status";
|
||||
gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
};
|
||||
|
||||
beeper {
|
||||
compatible = "gpio-beeper";
|
||||
gpios = <&gpio 4 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
};
|
||||
|
||||
&mdio1 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
ð1 {
|
||||
status = "okay";
|
||||
};
|
@ -0,0 +1,149 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
|
||||
/*
|
||||
* The hardware of this board family is most likely shared with other devices
|
||||
* from other manufacturers.
|
||||
* Devolo seems to use hardware from Edimax, namely the Edimax WAP1750.
|
||||
*
|
||||
* The base board is identical but the single models differ in number of
|
||||
* buttons, ethernet ports, external console, USB, external / internal
|
||||
* antennas and number of spatial streams.
|
||||
*/
|
||||
|
||||
/dts-v1/;
|
||||
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
|
||||
#include "qca9557.dtsi"
|
||||
|
||||
/ {
|
||||
chosen {
|
||||
bootargs = "console=ttyS0,115200n8";
|
||||
};
|
||||
|
||||
keys {
|
||||
compatible = "gpio-keys";
|
||||
|
||||
reset {
|
||||
label = "Reset button";
|
||||
linux,code = <KEY_RESTART>;
|
||||
gpios = <&gpio 18 GPIO_ACTIVE_LOW>;
|
||||
debounce-interval = <60>;
|
||||
};
|
||||
};
|
||||
|
||||
watchdog {
|
||||
compatible = "linux,wdt-gpio";
|
||||
gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
|
||||
hw_algo = "toggle";
|
||||
hw_margin_ms = <300>;
|
||||
always-running;
|
||||
};
|
||||
};
|
||||
|
||||
&pcie0 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&uart {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&gpio {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&spi {
|
||||
status = "okay";
|
||||
num-cs = <1>;
|
||||
|
||||
flash@0 {
|
||||
compatible = "jedec,spi-nor";
|
||||
reg = <0>;
|
||||
spi-max-frequency = <25000000>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "u-boot";
|
||||
reg = <0x000000 0x040000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@40000 {
|
||||
label = "u-boot-env";
|
||||
reg = <0x040000 0x010000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
art: partition@50000 {
|
||||
label = "art";
|
||||
reg = <0x050000 0x010000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@60000 {
|
||||
label = "art_bak";
|
||||
reg = <0x060000 0x010000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@70000 {
|
||||
compatible = "denx,uimage";
|
||||
label = "firmware";
|
||||
reg = <0x070000 0xf90000>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&mdio0 {
|
||||
status = "okay";
|
||||
|
||||
phy4: ethernet-phy@4 {
|
||||
reg = <4>;
|
||||
at803x-disable-smarteee;
|
||||
};
|
||||
};
|
||||
|
||||
ð0 {
|
||||
status = "okay";
|
||||
|
||||
mtd-mac-address = <&art 0x00>;
|
||||
phy-handle = <&phy4>;
|
||||
pll-data = <0xae000000 0x80000101 0x80001313>;
|
||||
|
||||
gmac_config: gmac-config {
|
||||
device = <&gmac>;
|
||||
|
||||
rxdv-delay = <3>;
|
||||
rxd-delay = <3>;
|
||||
txen-delay = <0>;
|
||||
txd-delay = <0>;
|
||||
rgmii-enabled = <1>;
|
||||
};
|
||||
};
|
||||
|
||||
&mdio1 {
|
||||
phy1: ethernet-phy@1 {
|
||||
reg = <1>;
|
||||
};
|
||||
};
|
||||
|
||||
ð1 {
|
||||
mtd-mac-address = <&art 0x00>;
|
||||
mtd-mac-address-increment = <1>;
|
||||
phy-handle = <&phy1>;
|
||||
pll-data = <0x03000101 0x00000101 0x00001313>;
|
||||
};
|
||||
|
||||
&wmac {
|
||||
status = "okay";
|
||||
mtd-cal-data = <&art 0x1000>;
|
||||
mtd-mac-address = <&art 0x00>;
|
||||
mtd-mac-address-increment = <(-2)>;
|
||||
};
|
Loading…
Reference in New Issue