TP-Link Archer C60 v3 is a dual-band AC1350 router,
based on Qualcomm/Atheros QCA9561 + QCA9886.
It seems to be identical to the v2 revision, except that
it lacks a WPS LED and has different GPIO for amber WAN LED.
Specification:
- 775/650/258 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 2T2R 5 GHz
- 5x 10/100 Mbps Ethernet
- 6x LED, 2x button
- UART header on PCB
Flash instruction (WebUI):
Download *-factory.bin image and upload it via the firmwary upgrade
function of the stock firmware WebUI.
Flash instruction (TFTP):
1. Set PC to fixed IP address 192.168.0.66
2. Download *-factory.bin image and rename it to tp_recovery.bin
3. Start a tftp server with the file tp_recovery.bin in its root
directory
4. Turn off the router
5. Press and hold reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time the firmware should
be transferred from the tftp server
8. Wait ~30 second to complete recovery
While TFTP works for OpenWrt images, my device didn't accept the
only available official firmware "Archer C60(EU)_V3.0_190115.bin".
In contrast to earlier revisions (v2), the v3 contains the (same)
MAC address twice, once in 0x1fa08 and again in 0x1fb08.
While the partition-table on the device refers to the latter, the
firmware image contains a different partition-table for that region:
name device firmware
factory-boot 0x00000-0x1fb00 0x00000-0x1fa00
default-mac 0x1fb00-0x1fd00 0x1fa00-0x1fc00
pin 0x1fd00-0x1fe00 0x1fc00-0x1fd00
product-info 0x1fe00-0x1ff00 0x1fd00-0x1ff00
device-id 0x1ff00-0x20000 0x1ff00-0x20000
While the MAC address is present twice, other data like the PIN isn't,
so with the partitioning from the firmware image the PIN on the device
would actually be outside of its partition.
Consequently, the patch uses the MAC location from the device (which
is the same as for the v2).
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 646d95c374)
Based on a script for comparison, this fixes (hopefully) all errors
in SUPPORTED_DEVICES for ar71xx->ath79 upgrade.
Devices where old string is removed as the device does not exist
in ar71xx:
- dlink_dir-859-a1
- tplink_archer-a7-v5
- tplink_cpe510-v3 [only in master]
Devices where string is changed because it did not match the board
name in ar71xx:
- tplink_tl-mr3220-v1
- tplink_tl-mr3420-v1
- tplink_tl-wr2543-v1
- tplink_tl-wr741nd-v4
- tplink_tl-wr841-v7
- ubnt_unifiac-mesh
- ubnt_unifiac-mesh-pro
- ubnt_unifiac-pro
For this device, the correct string could not be found, but we could
not determine the correct one. Thus, the string is removed for now:
- tplink_tl-wr740n-v4
The script for checking this is quite simple (note that newer
entries, i.e. ath79->ath79 upgrade, are displayed as missing):
newpath=target/linux/ath79/image/
oldpath=target/linux/ar71xx/base-files/lib/ar71xx.sh
for s in $(grep -roh "SUPPORTED_DEVICES.*" $newpath | sed 's/SUPPORTED_DEVICES *.= *//'); do
found="Missing"
grep -q -r "\"$s\"" $oldpath && found="Found"
echo "$s: $found."
done
The errors might be filtered by appending 'grep "Missing"' to the script.
Fixes: FS#2751
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 07ce940b77)
This device has not been supported in ar71xx, so there is no need
for an explicit SUPPORTED_DEVICES entry.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 894bdee756)
This adds support for a popular low-cost 2.4GHz N based AP
Specifications:
SoC: Qualcomm Atheros QCA9533 (650MHz)
RAM: 64MB
Storage: 8 MB SPI NOR
Wireless: 2.4GHz N based built into SoC 2x2
Ethernet: 2x 100/10 Mbps, integrated into SoC
Installation:
Flash factory image through stock firmware WEB UI
or through TFTP
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP adress:192.168.0.254
This also applies some minor changes to the common DTSI:
- use &wmac for label-mac-device, as this one is actually set up in
common DTSI
- move ð0 to parent DTSI
- fix several leading spaces, added/removed newlines
Signed-off-by: Andrew Cameron <apcameron@softhome.net>
[DTS style fixes/improvements, updated commit message/title,
backport to 19.07]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The TL-WDR4300 v1 sold in Israel has a different TPLINK_HWID.
Thanks to Josh4300 for testing on device.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit c642a97aa6)
TP-Link Archer C60 v2 is a dual-band AC1350 router,
based on Qualcomm/Atheros QCA9561 + QCA9886.
Specification:
- 775/650/258 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 2T2R 5 GHz
- 5x 10/100 Mbps Ethernet
- 7x LED, 2x button
- UART header on PCB
Flash instruction (WebUI):
Download *-factory.bin image and upload it via the firmwary upgrade
function of the stock firmware WebUI.
Flash instruction (TFTP):
1. Set PC to fixed IP address 192.168.0.66
2. Download *-factory.bin image and rename it to tp_recovery.bin
3. Start a tftp server with the file tp_recovery.bin in its root
directory
4. Turn off the router
5. Press and hold reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time the firmware should
be transferred from the tftp server
8. Wait ~30 second to complete recovery
Flash instruction (under U-Boot, using UART):
tftp 0x81000000 ...-sysupgrade.bin
erase 0x9f030000 +$filesize
cp.b $fileaddr 0x9f030000 $filesize
reset
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 974d6958a7)
TP-Link Archer C60v1 is a dual-band AC1350 router,
based on Qualcomm/Atheros QCA9561+QCA9886.
Specification:
- 775/650/258 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 2T2R 5 GHz
- 5x 10/100 Mbps Ethernet
- 7x LED, 2x button
- UART header on PCB
Flash instruction (WebUI):
Download *-factory.bin image and upload it via the firmwary upgrade
function of the stock firmware WebUI.
Flash instruction (TFTP):
1. Set PC to fixed ip address 192.168.0.66
2. Download *-factory.bin image and rename it to tp_recovery.bin
3. Start a tftp server with the file tp_recovery.bin in its root directory
4. Turn off the router
5. Press and hold Reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time
the firmware should be transferred from the tftp server
8. Wait ~30 second to complete recovery.
Flash instruction under U-Boot, using UART:
1. tftp 0x81000000 ...-sysupgrade.bin
2. erase 0x9f020000 +$filesize
3. cp.b $fileaddr 0x9f020000 $filesize
4. reset
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 6d313da6dc)
Ath10k packages were removed from ar71xx in master in commit
34113999ef ("ar71xx: Remove ath10k packages from archer-c7-v1 (fixes
FS#1743)") but ath79 in master and the 19.07 branch still suffer from
the issue.
Signed-off-by: Stijn Segers <foss@volatilesystems.org>
[commit subject and description facelift]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
In ar71xx, the board name for the TL-WR1043ND v3 is equal to v2:
tl-wr1043nd-v2
Fix SUPPORTED_DEVICES for v3 in ath79 accordingly.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit b5791118cc)
In ath79, identifiers tplink_tl-wdr3600 and tplink_tl-wdr4300 have
been used while most other TP-Link devices include the revision.
Although there actually is only one major revision of these
devices, they bear the revision on their bottom (v1.x). TP-Link
also refers to the devices as V1 on its web page.
This patch thus adds -v1 to both so it is more consistent
with other devices and with what you would expect from reading
the on-device sticker and the support pages.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The TP-Link Archer C25 is a low-cost dual-band router.
Specification:
- CPU: Atheros QCA9561 775 MHz
- RAM: 64 MB
- Flash: 8 MB
- Wifi: 3x3 2.4 GHz (integrated), 1x1 5 GHz QCA9887
- NET: 5x 10/100 Mbps Ethernet
Some LEDs are controlled by an additional 74HC595 chip, but not
all of them as e.g. for the C59.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
TP-Link Archer D50 v1 is a dual-band AC1200 router + modem.
The router section is based on Qualcomm/Atheros QCA9531 + QCA9882.
The "DSL" section is based on BCM6318 but it's currently not supported.
Internally eth0 is connected to the Broadcom CPU.
Router section - Specification:
CPU: QCA9531 650/600/200 MHz (CPU/DDR/AHB)
RAM: 64 MB (DDR2)
Flash: 8 MB (SPI NOR)
Wifi 2.4GHz: QCA9531 2T2R
Wifi 5GHz: QCA9982 2T2R
4x 10/100 Mbps Ethernet
8x LED, 3x button
UART header on PCB
Known issues:
DSL not working (eth0) (WIP)
UART connection
---------------
J2 HEADER (Qualcomm CPU)
. TX
. RX
. GND
O VCC
J16 HEADER (Broadcom CPU)
O VCC
. GND
. RX
. TX
The following instructions require a connection to the J2 UART header.
Flash instruction under U-Boot, using UART
------------------------------------------
1. Press any key to stop autobooting and obtain U-Boot CLI access.
2. Setup ip addresses for U-Boot and your tftp server.
3. Issue below commands:
tftpboot 0x81000000 openwrt-ath79-generic-tplink_archer-d50-v1-squashfs-sysupgrade.bin
erase 0x9f020000 +$filesize
cp.b 0x81000000 0x9f020000 $filesize
reset
Initramfs instruction under U-Boot for testing, using UART
----------------------------------------------------------
1. Press any key to stop autobooting and obtain U-Boot CLI access.
2. Setup ip addresses for U-Boot and your tftp server.
3. Issue below commands:
tftpboot 0x81000000 openwrt-ath79-generic-tplink_archer-d50-v1-initramfs-kernel.bin
bootm 0x81000000
Restore the original firmware
-----------------------------
0. Backup every partition using the OpenWrt web interface
1. Download the OEM firmware from the TP-Link website
2. Extract the bin file in a folder (eg. Archer_D50v1_0.8.0_1.3_up_boot(170223)_full_2017-02-24_09.37.45.bin)
3. Remove the U-Boot and the Broadcom image part from the file.
Issue the following command:
dd if="Archer_D50v1_0.8.0_1.3_up_boot(170223)_full_2017-02-24_09.37.45.bin" of="Archer_D50v1_0.8.0_1.3_up_boot(170223)_full_2017-02-24_09.37.45.bin.mod" skip=257 bs=512 count=15616
4. Double check the .mod file size. It must be 7995392 bytes.
5. Flash it using the OpenWrt web interface. Force the update if needed.
WARNING: Remember to NOT keep settings.
5b. (Alternative to 5.) Flash it using the U-Boot and UART connection.
Issue below commands in the U-Boot:
tftpboot 0x81000000 Archer_D50v1_0.8.0_1.3_up_boot(170223)_full_2017-02-24_09.37.45.bin.mod
erase 0x9f020000 +$filesize
cp.b 0x81000000 0x9f020000 $filesize
reset
Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [removed
default-state = "off", it's already the default, added pcie node,
fixed typo]
Specifications:
- QCA9563 at 775 MHz
- 64 MB RAM Zentel A3R12E40CBF-8E
- 16 MB flash Winbond W25Q128FVSG
- 3 (non-detachable) Antennas / 450 Mbit
- 1x/4x WAN/LAN Gbps Ethernet (QCA8337)
- reset and Wi-Fi buttons
TP-Link TL-WR1043N v5 appears to be identical to the TL-WR1043ND v4,
except that the USB port has been removed and there is no longer a
removable antenna option. It also has different partitioning scheme.
The software is more in line with the Archer series in that it uses a
nested bootloader scheme.
(This has been adapted from the OpenWrt Wiki page)
<https://openwrt.org/toh/tp-link/tl-wr1043nd>
Installation on HW rev.5:
Factory firmware can be installed via the WEB interface.
Alternatively, it is also possible to use a TFTP server
for recovery purposes:
- Rename OpenWRT or original firmware to WR1043v5_tp_recovery.bin
- Set static IP of your PC to *192.168.0.66*
- Router will obtain IP 192.168.0.86 for a few seconds while
loading, when reset button pressed at power On.
And finally, there's always u-boot access through the UART.
For information visit the wiki.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[reworked commit message]
This adds support for the TP-Link WR842N v3 which is already supported on ar71xx
target (0b45bec22c).
Specification:
* SoC: QCA9533 ver 2 rev 0
* 16 MB Flash (gd25q128)
* 64 MB RAM
* 1 WAN 10/100 MBit/s (blue connector)
* 4 LAN 10/100 MBit/s (AR8229; 4 ports; yellow connectors)
* Atheros AR9531 (2,4GHz, two fixed antennas)
* USB
* Reset / WPS button
* WiFi button (rf kill)
* 8 green leds; 1 red/green led
* serial console (115200 8N1, according to the OpenWrt-wiki some soldering is needed)
Installation:
* flash via vendor WebUI (the filename must not exceed certain length)
* sysupgrade from installed OpenWrt (also ar71xx)
Thanks to Holger Drefs for providing the hardware
Tested-by: @kofec (github)
Signed-off-by: Sven Roederer <devel-sven@geroedel.de>
Currently, tplink-safeloader definition is only used a base for
another common definition.
This patch adjusts tplink-safeloader so it can be actually used
for some targets in generic-tp-link.mk.
This patch is cosmetic except for the order of
"check-size $$$$(IMAGE_SIZE)" and "append-metadata" exchanged
for the tplink_re350k-v1 .
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [dealed with
tplink_cpe210-v2 and tplink_cpe210-v3, removed tplink-safeloader-uimage's
extra IMAGE/sysupgrade.bin rule]
This PR adds support for a popular low-cost 2.4GHz N based AP
Specifications:
- SoC: Qualcomm Atheros QCA9533 (650MHz)
- RAM: 64MB
- Storage: 8 MB SPI NOR
- Wireless: 2.4GHz N based built into SoC 2x2
- Ethernet: 1x 100/10 Mbps, integrated into SoC, 24V POE IN
Installation:
Flash factory image through stock firmware WEB UI
or through TFTP
To get to TFTP recovery just hold reset button while powering on
for around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP adress:192.168.0.254
This is based on the support patch for the identical CPE210 v3
by Mario Schroen <m.schroen@web.de>.
Tested-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
[renamed dtsi filename]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Specifications:
* SoC: Qualcomm Atheros QCA9533 (650MHz)
* RAM: 64MB
* Storage: 8 MB SPI NOR
* Wireless: 2.4GHz N based built into SoC 2x2
* Ethernet: 1x 100/10 Mbps, integrated into SoC, 24V POE IN
Installation:
Flash factory image through stock firmware WEB UI or TFTP
To get to TFTP recovery just hold reset button while powering
on for around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP adress:192.168.0.254
Thanks to robimarko for the work inside the ar71xx tree.
Thanks to adrianschmutzler for deep discussion and fixes.
Signed-off-by: Mario Schroen <m.schroen@web.de>
[Split into DTS/DTSI, read-only config partition in DTSI]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
[renamed dtsi filename, light subject touches]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This commit adds support for TP-Link TL-WR710N v1 router.
CPU: Atheros AR9331 400MHz
RAM: 32MB
FLASH: 8MiB
PORTS: 1 Port 100/10 LAN (connected to a switch), 1 Port 100/10 WAN
WiFi: Atheros AR9331 1x2:1 bgn
USB: ChipIdea HDRC USB2.0
LED: SYS
BTN: Reset
Sysupgrade from `ar71xx` works without glitches.
Network interfaces assigned for LAN and WAN ports are `eth1` and `eth0`
respectively, what's consistent with `ar71xx` target. Wireless radio
path is automatically upgraded from `platform/ar933x_wmac` to
`platform/ahb/18100000.wmac`.
Signed-off-by: Marcin Jurkowski <marcin1j@gmail.com>
TP-Link RE350K v1 (FCC ID: TE7RE350K) is a wall-plug AC1200 Wi-Fi range
extender with 'Kasa Smart' support. Device is based on Qualcomm/Atheros
QCA9558 + QCA9882 + AR8035 platform and is available only on US market.
Specification:
- 720/600/200 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of flash (SPI NOR)
- 1x 1 Gbps Ethernet (AR8035)
- 2T2R 2.4 GHz (QCA9558), with ext. PA (SE2565T) and LNA (SKY65971-11)
- 2T2R 5 GHz (QCA9882), with ext. PA (SE5003L1-R) and LNA (SKY65981-11)
- 2x U.FL connector on PCB
- 2x dual-band PCB antennas
- 1x LED, 2x dual-color LED (all driven by GPIO)
- 3x button (app config, led, reset)
- 1x mechanical on/off slide switch
- 1x UART (4-pin, 2.54 mm pitch) header on PCB
- 1x JTAG (8-pin, 1.27 mm pitch) header on PCB
Flash instruction:
Use 'factory' image directly in vendor GUI (default IP: 192.168.0.254,
default credentials: admin/admin).
Warning:
This device does not include any kind of recovery mechanism in U-Boot.
Vendor firmware access:
You can access vendor firmware over serial (RX line requires jumper
resistor in R306 place, near XTAL) with: root/sohoadmin credentials.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
The TP-Link WDR3600 shares the same machine-code in the ar71xx target,
thus expecting "tl-wdr4300" not "tl-wdr3600" in the support-list
metadata to allow non-forced sysupgrades from ar71xx to ath79.
With this, it is possible to flash a WDR4300 image on the WDR3600. It
is no problem however, as the only difference is the 5GHz WiFi chip
which has 3SS instead of 2SS. Both work with either image.
Signed-off-by: David Bauer <mail@david-bauer.net>
TP-Link Archer C7 v4 is a dual-band AC1750 router, based on the
Qualcomm/Atheros QCA9561 SoC + QCA9880.
Specification:
- 775/650/258 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 3T3R 5 GHz
- 5x 10/100/1000 Mbps Ethernet
- 7x LED, 2x button
- UART header on PCB
Flash instruction:
1. Upload openwrt-ath79-generic-tplink_archer-c7-v4-squashfs-factory.bin
via Web interface
Flash instruction using TFTP recovery:
1. Set PC to fixed ip address 192.168.0.66
2. Download openwrt-ath79-generic-tplink_archer-c7-v4-squashfs-factory.bin
and rename it to ArcherC7v4_tp_recovery.bin
3. Start a tftp server with the file tp_recovery.bin in its root directory
4. Turn off the router
5. Press and hold Reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time
the firmware should be transferred from the tftp server
8. Wait ~30 second to complete recovery.
Signed-off-by: Oldřich Jedlička <oldium.pro@gmail.com>
This patch adds support for TP-Link Archer C6 v2 (EU)
Hardware specification:
- SOC: Qualcomm QCA9563 @ 775MHz
- Flash: GigaDevice GD25Q64CSIG (8MiB)
- RAM: Zentel A3R1GE40JBF (128 MiB DDR2)
- Ethernet: Qualcomm QCA8337N: 4x 1Gbps LAN + 1x 1Gbps WAN
- Wireless:
- 2.4GHz (bgn) QCA9563 integrated (3x3)
- 5GHz (ac) Qualcomm QCA9886 (2x2)
- Button: 1x power, 1x reset, 1x wps
- LED: 6x LEDs: power, wlan2g, wlan5g, lan, wan, wps
- UART: There's no UART header on the board
Flash instructions:
Upload
openwrt-ath79-generic-tplink_archer-c6-v2-squashfs-factory.bin
via the router Web interface.
Flash instruction using tftp recovery:
1. Connect the computer to one of the LAN ports of the router
2. Set the computer IP to 192.168.0.66
3. Start a tftp server with the OpenWrt factory image in the
tftp root directory renamed to ArcherC6v2_tp_recovery.bin.
4. Connect power cable to router, press and hold the reset
button and turn the router on
5. Keep the reset button pressed until the WPS LED lights up
6. Wait ~150 seconds to complete flashing
According to the GPL source the non-EU variant has different
GPIOs assigned to some of the LEDs and buttons. The flash
layout might be different as well. The wikidevi entry for
Archer A6/C6 assumes they are identical.
Signed-off-by: Georgi Vlaev <georgi.vlaev@gmail.com>
This commit adds support for TP-Link Archer C7 v5, leveraging most effort
from commit ea9baee and 1e4ee63. Archer C7 v5 is identical to Archer A7 v5
but with a different flash layout.
Specification:
- QCA9563 SoC (750 MHz)
- 128 MiB of RAM (DDR2)
- 16 MiB of flash (SPI)
- 5x 1 Gbps Ethernet (1x WAN + 4x LAN)
- 2.4GHz (bgn) SoC internal + 5GHz (ac) QCA9880
- 10x LED, 2x button
- UART header on PCB
Flash instructions:
1. Upload openwrt-ath79-generic-tplink_archer-c7-v5-squashfs-factory.bin
via web interface.
Flash instructions using TFTP recovery:
1. Plug PC to one of the LAN ports
2. Set PC to fixed IP address 192.168.0.66
3. Rename the factory image to ArcherC7v5_tp_recovery.bin and place it in
TFTP root directory
4. Turn on the router with the reset button pressed for about 15 secs
5. Release the button and wait about 150 secs to complete flashing
Signed-off-by: TOCK Chiu <tock.chiu@gmail.com>
This patch adds support for TP-Link Archer A7
Specification:
- SOC: QCA9563
- Flash: 16 MiB (SPI)
- RAM: 128 MiB (DDR2)
- Ethernet: 4x 1Gbps LAN + 1x 1Gbps WAN
- Wireless:
- 2.4GHz (bgn) SoC internal
- 5GHz (ac) QCA988x
- USB: 1x USB 2.0 port
- Button: 1x power, 1x reset, 1x wps
- LED: 10x LEDs
- UART: holes in PCB
- Vcc, GND, RX, TX from ethernet port side
- 115200n8
Flash instructions:
Upload openwrt-ath79-generic-tplink_archer-a7-v5-squashfs-factory.bin
via the Webinterface.
Flash instruction using tftp recovery:
1. Connect the computer to one of the LAN ports of the Archer A7
2. Set the computer IP to 192.168.0.66
3. Start a tftp server with the OpenWrt factory image in the tftp
root directory renamed to ArcherC7v5_tp_recovery.bin
2. Connect power cable to Archer A7, press and hold the reset button
and turn the router on
3. Keep the reset button pressed for ~5 seconds
4. Wait ~150 seconds to complete flashing
Changes since first revision:
- Flash instructions using stock image webinterface
- Changed "Version 5" in model string to "v5"
- Split DTS file in qca9563_tplink_archer-x7-v5.dtsi
and qca9563_tplink_archer-a7-v5.dts
- Firmware image is now build with dynamic partitioning
- Default to ath10k-ct
Changes since second revision:
- Changed uboot@0 to uboot@20000 in DTS file
- Fixed ordering issue in board led script
- Specify firmware partition format in DTS file
- Rebased Makefile device definition on common
Device/tplink-safeloader-uimage definition
- Merged switch section in network script
(same configuration as tplink,tl-wdr3600
and tplink,tl-wdr4300)
Signed-off-by: Karl-Felix Glatzer <karl.glatzer@gmx.de>
This ports support for TP-Link TL-WR842N/ND v1 from ar71xx.
CPU: Atheros AR7241 400 MHz
RAM: 32 MiB
FLASH: 8 MiB
PORTS: 4 Port 100/10 Switch, 1 Port 100/10 Wan
WiFi: Atheros AR9287
LED: SYS, WiFi, LAN, WAN, 3G, QSS
BTN: WiFi, Reset/WPS
AR71xx target used "tl-mr3420" as board id so force flag is needed
if upgrading from old target.
Signed-off-by: Marcin Jurkowski <marcin1j@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [trivial cleanup]
This commit adds support for the Archer C58 v1 and C59 v1, previously
supported in the ar71xx target.
CPU: Qualcomm QCA9561
RAM: 64M (C58) / 128M (C59)
FLASH: 8M (C58) / 16M (C59)
WiFi: QCA9561 bgn 3x3:3
QCA9888 nac 2x2:2
LED: Power, WiFi 2.4, WiFi 5, WAN green, WAN amber, LAN, WPS
Only C59: USB
BTN: WPS, WiFi, Reset
Installation
------------
Via Web-UI:
Update factory image via Web-UI.
Via TFTP:
Rename factory image to "tp_recovery.bin" and place it in the root-dir
of your tftp server. Configure to listen on 192.168.0.66. Power up the
router while holding down the reset-button. The router will flash itself
and reboot.
Note: For TFTP, you might need a switch between router and computer, as
link establishment might take to long.
Signed-off-by: David Bauer <mail@david-bauer.net>
This PR adds support for TP-Link TL-WR842N-v2 router which is supported by ar71xx to ath79.
This is a low cost model with following specs:
CPU: Atheros AR9341 SoC
RAM: 32 MB DDR1
Flash: 8 MB NOR SPI
Switch: Internal AR9341 5 port 10/100 Mbit
Ports: 5x 10/100 Mbit(1x WAN, 4x LAN)
USB: 1x USB2.0
WLAN: 2.4 GHZ AR9341
Installation:
Simply flash the factory image through stock firmware WEB UI.
Signed-off-by: Robert Marko <robimarko@gmail.com>
We select ath10k-ct by default, but it is still possible to build
the upstream version.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John Crispin <john@phrozen.org>
TP-Link Archer C7 v1 is a dual band router
based on Qualcomm/Atheros QCA9558 + QCA9880.
Specification:
- 720 MHz CPU
- 128 MB of RAM (Various chips)
- 8 MB of FLASH (Various chips)
- SoC QCA9558 integrated 3T3R 2.4 GHz Wi-Fi
- minipcie slot with 3T3R 5 GHz QCA9880-AR1A (unsupported by ath10k!)
- 5x 10/100/1000 Mbps Ethernet (AR8327N Switch)
- 10x LEDs, 2x software buttons
For further informwation on the device, visit the wiki:
<https://openwrt.org/toh/tp-link/archer-c7-1750>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This router is called RE450 and the tl prefix was used to identify it
as a TP-Link device. Drop the tl prefix since we now have tplink in
dts and device name.
Signed-off-by: Peter Lundkvist <peter.lundkvist@gmail.com>
Including the tl-wdr3600 image build code just to overwrite most of it
doesn't make much sense and only makes it hard to read.
Furthermore, the tl-wdr4300 image will be marked as compatible with the
tl-wdr3600 this way.
Signed-off-by: Mathias Kresin <dev@kresin.me>
This router is called Archer C7 and the tl was used to identify
TP-LINK. Since we have added tplink in dts/board name, the tl
prefix is useless now.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
- fix sysupgrade check
- move usb to v4 dts because v5 doesn't have it
- make wan mac address behave like ar71xx target
- add orange wan led support, it can be userspace activated like:
on:
echo default-on > /sys/class/leds/tp-link\:orange\:wan/trigger
off:
echo none > /sys/class/leds/tp-link\:orange\:wan/trigger
Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
Use the new dynamic partition split in tplink-safeloader so we no longer
have to worry about kernel size increases.
Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
Adrian Schmutzler
Andrew Cameron
Paul Fertser
Stijn Segers
Davide Fioravanti
Sven Roederer
Mario Schroen
Marcin Jurkowski
Piotr Dymacz
Bart Lauret
David Bauer
Paul Wassi
Oldřich Jedlička
Skirmantas Lauzikas
Georgi Vlaev
TOCK Chiu
Karl-Felix Glatzer
Mathias Kresin
Robert Marko
John Crispin
Christian Lamparter
Peter Lundkvist
Chuanhong Guo
Lucian Cristian
Sibren Vasse
Alex Maclean