ath79: add TP-Link WR842N v3
This adds support for the TP-Link WR842N v3 which is already supported on ar71xx
target (0b45bec22c).
Specification:
* SoC: QCA9533 ver 2 rev 0
* 16 MB Flash (gd25q128)
* 64 MB RAM
* 1 WAN 10/100 MBit/s (blue connector)
* 4 LAN 10/100 MBit/s (AR8229; 4 ports; yellow connectors)
* Atheros AR9531 (2,4GHz, two fixed antennas)
* USB
* Reset / WPS button
* WiFi button (rf kill)
* 8 green leds; 1 red/green led
* serial console (115200 8N1, according to the OpenWrt-wiki some soldering is needed)
Installation:
* flash via vendor WebUI (the filename must not exceed certain length)
* sysupgrade from installed OpenWrt (also ar71xx)
Thanks to Holger Drefs for providing the hardware
Tested-by: @kofec (github)
Signed-off-by: Sven Roederer <devel-sven@geroedel.de>
v19.07.3_mercusys_ac12_duma
Sven Roederer
5 years ago
committed by
Christian Lamparter
parent
9385ff654e
commit
e0d98e120a
@ -0,0 +1,168 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
/dts-v1/;
|
||||
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
|
||||
#include "qca953x.dtsi"
|
||||
|
||||
/ {
|
||||
compatible = "tplink,tl-wr842n-v3", "qca,qca9533";
|
||||
model = "TP-Link TL-WR842N v3";
|
||||
|
||||
aliases {
|
||||
led-boot = &qss_led;
|
||||
led-failsafe = &qss_led;
|
||||
led-running = &qss_led;
|
||||
led-upgrade = &qss_led;
|
||||
};
|
||||
|
||||
gpio_leds: leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
system: power {
|
||||
label = "tp-link:green:power";
|
||||
gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
|
||||
default-state = "on";
|
||||
};
|
||||
|
||||
wifi {
|
||||
label = "tp-link:green:wlan";
|
||||
gpios = <&gpio 3 GPIO_ACTIVE_LOW>;
|
||||
linux,default-trigger = "phy0tpt";
|
||||
};
|
||||
|
||||
qss_led: qss {
|
||||
label = "tp-link:green:qss";
|
||||
gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
wan_green {
|
||||
label = "tp-link:green:wan";
|
||||
gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
wan_red {
|
||||
label = "tp-link:red:wan";
|
||||
gpios = <&gpio 4 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
lan1 {
|
||||
label = "tp-link:green:lan1";
|
||||
gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
lan2 {
|
||||
label = "tp-link:green:lan2";
|
||||
gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
lan3 {
|
||||
label = "tp-link:green:lan3";
|
||||
gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
lan4 {
|
||||
label = "tp-link:green:lan4";
|
||||
gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
usb {
|
||||
label = "tp-link:green:usb";
|
||||
gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
|
||||
linux,default-trigger = "usbport";
|
||||
trigger-sources = <&hub_port>;
|
||||
};
|
||||
};
|
||||
|
||||
keys {
|
||||
compatible = "gpio-keys";
|
||||
|
||||
reset {
|
||||
label = "Reset button";
|
||||
linux,code = <KEY_RESTART>;
|
||||
gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
|
||||
debounce-interval = <60>;
|
||||
};
|
||||
|
||||
rfkill {
|
||||
label = "RFKILL button";
|
||||
linux,code = <KEY_RFKILL>;
|
||||
gpios = <&gpio 0 GPIO_ACTIVE_LOW>;
|
||||
debounce-interval = <60>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&uart {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usb0 {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
status = "okay";
|
||||
|
||||
hub_port: port@1 {
|
||||
reg = <1>;
|
||||
#trigger-source-cells = <0>;
|
||||
};
|
||||
};
|
||||
|
||||
&usb_phy {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&spi {
|
||||
status = "okay";
|
||||
num-cs = <1>;
|
||||
|
||||
flash@0 {
|
||||
compatible = "jedec,spi-nor";
|
||||
reg = <0>;
|
||||
spi-max-frequency = <25000000>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
uboot: partition@0 {
|
||||
label = "u-boot";
|
||||
reg = <0x000000 0x020000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@20000 {
|
||||
compatible = "tplink,firmware";
|
||||
label = "firmware";
|
||||
reg = <0x020000 0xfd0000>;
|
||||
};
|
||||
|
||||
art: partition@ff0000 {
|
||||
label = "ART";
|
||||
reg = <0xff0000 0x010000>;
|
||||
read-only;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
ð1 {
|
||||
mtd-mac-address = <&uboot 0x1fc00>;
|
||||
};
|
||||
|
||||
ð0 {
|
||||
status = "okay";
|
||||
phy-handle = <&swphy4>;
|
||||
|
||||
mtd-mac-address = <&uboot 0x1fc00>;
|
||||
mtd-mac-address-increment = <1>;
|
||||
};
|
||||
|
||||
&wmac {
|
||||
status = "okay";
|
||||
mtd-cal-data = <&art 0x1000>;
|
||||
mtd-mac-address = <&uboot 0x1fc00>;
|
||||
};
|
||||
|
||||
Loading…
Reference in New Issue