When the gettext-full host build phase finds an `emacs` exectuble during the
build it will launch an `emacs --batch` command to run some Lisp code.
On certain Debian systems the `/usr/bin/emacs` path might point, via
alternatives, to the `/usr/bin/jove` editor which will then launch an
interactive session when invoked by the gettext build.
In order to avoid this problem, explicitely disable emacs handling during
the build through a configure environment variable.
Also remove my now unreachable maintainer address.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The previous image creation code would have failed if the
unpadded kernel uImage size was less than 64 bytes from the
next erase block boundary. Fix that.
Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>
The CPE210 was still described for the OEM upgrade as compatible,
even the wireless configuration isn't compatible anymore between
both series (2ghz and 5ghz).
Update the CPE210 image profile to use the new profile.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
The CPE210's ancestor is the CPE510 not the other way around. The device
profile is also named after the CPE510.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
The bootloader on this device expects the kernel partition to end
on a 64k boundary. The last 64 byte of the kernel partition must
contain a valid uImage header (the fakeroot partition).
Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>
1)Changes
- Rebased the patches for linux-4.4.7
- Added patch to fix spi nor fifo and dma support
- Added patch to configure watchdog barktime
2)Testing
Tested on IPQ AP148 Board:
a. NOR boot and NAND boot
b. ethernet network and ath10k wifi
c. ubi sysupgrade
UnTested
dwc3 usb has not been validated on IPQ board(AP148)
3)Known Issues:
Once we flash ubi image on AP148, and if we reset the board, uboot on
first boot creates PEB and LEB for dynamic sized partitions, which is incorrect
and not what linux expects which causes errors when trying to mount rootfs.
In order to test this, we can use the below steps:
a. Flash the ubi image on board and don't reset the board
b. load the kernel fit image in RAM and boot from there.
Signed-off-by: Ram Chandra Jangir <rjangi@codeaurora.org>
The user benpicco in #openwrt reported that images are build which are
bigger that the available flash size.
He provided a proof of concept fix and gave permission to me to send it
for inclusion.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The RJ45 WAN port is used for xDSL as well as the IP101A.
The pins 1,2,3,6 of the RJ45 are connected to the IP101A and the
pins 4,5 are connected to the xdsl chip.
Drop the ip101a-rst node. It can't be controlled and is not required
at all.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The STP pinmux was initially added in assumption LAN2 led is driven by
it. It worked somehow because STP group and gphy0 led0 share the GPIO.
Do it the right way by adding the gphy0 led0 the gphy function.
According to the author, the SPI node is a copy & paste leftover. Which
makes sense since nothing is connected to the SPI bus on this device.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Based on a submission to the uboot-lantiq repo by Eddi De Pieri.
Major cleanup and addition of brnboot second stage u-boot was done by
me.
The second stage brnboot u-boot is untested, since the brnboot prompt
is secured by a still unknown password. But should work.
The former ram values are replaced with the ram values extracted from
the original brnboot. The old ones didn't worked with the ramboot
image.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The default bootloader partition of some devices is to small for an
u-boot with uncompressed gphy firmware(s).
Instead of increasing the bootloader partition size, in compare to the
stock firmware, compress the firmware. This would allow the bootloader
of at least the FritzBox 3370 as well as the bootloader of the
VGV7510KW22 to fit into the bootloader partition of the stock firmware.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Based on a submission to the uboot-lantiq repo by Eddi De Pieri.
Devices like the xrx200 Arcadyan VGV7519 are using two NOR flash chips.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Use the brnboot partition layout as it is listed in the OpenWrt wiki
article for this board.
Configure the brnboot root selector for this device as well.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Cleanup the pinmux configuration by removing the unused spi node. Nothing is connected to the SPI bus on devices.
The stp_out pinmux child node covers the same GPIOs as the already used
stp group.
The same applies to the gphy-leds_out pinmux node and the "gphy0
led1" as well as "gphy1 led0" groups.
Signed-off-by: Mathias Kresin <dev@kresin.me>
This patch fixes the missing Lan interface config in the file
/etc/config/network for ARV4518PWR01/A which results in eth0 and br-lan
being down and therefore no way to access the router unless via UART-TTL.
Signed-off-by: Mohammed Berdai <mohammed.berdai@gmail.com>
This makes brcmfmac compatible with mac80211 which uses dev_alloc_name
(and so returns -ENFILE on error).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
LEDE project seems to be using "LEDE" as its acronym everywhere. To keep
things consistent adjust default wireless SSID.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Jo-Philipp Wich <jo@mein.io>
Acked-by: John Crispin <john@phrozen.org>
Acked-by: Alexander Couzens <lynxis@fe80.eu>
Provide HTTPS URL when possible, try to keep 8 mirrors per entry and spread
over several locations of the world. Since most active contributors are in
US/CA and/or EU prioritize mirrors that are within those regions if possible.
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
The igb kmods selects kmod-i2c-algo-bit which in turn is invisible until
kmod-i2c-core gets selected, causing kmod-igb to be hidden from menuconfig
as well.
Let kmod-igb select kmod-i2c-core as well in order to make it visible
in menuconfig right away.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
- install correct libs to staging/usr/lib
fixes eudev, nfs-kernel-server
the lib*.a seem broken - use the correct .so files
and remove .a libs
- some build breakage was observed with parallel builds:
text-utils/more-more.o: In function `putstring':
more.c:(.text+0x1f4): undefined reference to `tputs'
text-utils/more-more.o: In function `initterm':
more.c:(.text+0x1b74): undefined reference to `setupterm'
more.c:(.text+0x1f0c): undefined reference to `tparm'
more.c:(.text+0x20ac): undefined reference to `tigetnum'
more.c:(.text+0x20c8): undefined reference to `tigetflag'
more.c:(.text+0x20ec): undefined reference to `tigetstr'
more.c:(.text+0x2148): undefined reference to `PC'
text-utils/more-more.o: In function `reset_tty':
more.c:(.text+0x2630): undefined reference to `tputs'
- fix line length
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
Florian Eckert
Stijn Segers
Jo-Philipp Wich
John Crispin
Maxim Storchak
Joseph C. Lehner
Daniel Gimpelevich
Alexander Couzens
Ash Benz
Ram Chandra Jangir
Alexey Brodkin
Mathias Kresin
Mohammed Berdai
Rafał Miłecki
Álvaro Fernández Rojas
Daniel Engberg
Dirk Neukirchen