Without this patch, when using rev 3 of the Atheros AR9344 SoC, the
gigabit switch (AR8327) does not work or works very erratically.
This is a re-spin of http://patchwork.ozlabs.org/patch/419857/ with a
different PLL value, according to the feedback from several users
(including myself) as shown here:
https://openwrt.org/toh/mikrotik/rb2011uias#tracking_reported_experience_with_suggested_patch_for_the_5_gige_ports
Performance is acceptable: testing L3 forwarding without NAT yields a
performance of 370 Mbit/s (iperf3 TCP) and 41 Kpps (iperf3 UDP with 64
bytes payload). Both tests show that 100% of CPU time is spent on softirq.
A similar fix for a different device (RB2011) was added in e457d22261
("Make GBit switch work on RB2011").
Signed-off-by: Baptiste Jonglez <git@bitsofnetworks.org>
The bootloader does not always initialize the MDIO pins before booting
Linux. E.g. on version "U-Boot 2012.07 [Chaos Calmer 15.05.1,r35193] (Jul
25 2017 - 11:36:26)" this is the case when booting automatically without
activating the U-Boot console.
Without this change, the kernel boot will complain about missing PHYs:
libphy: ipq40xx_mdio: probed
ar40xx c000000.ess-switch: Probe failed - Missing PHYs!
libphy: Fixed MDIO Bus: probed
With this change it will work as expected:
libphy: ipq40xx_mdio: probed
ESS reset ok!
ESS reset ok!
libphy: Fixed MDIO Bus: probed
Ref: GH-2835
Tested-by: Fredrik Olofsson <fredrik.olofsson@anyfinetworks.com>
Signed-off-by: Leon M. George <leon@georgemail.eu>
[commit description from Fredrik, subject facelift]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Seems to be working fine on my a64-olinuxino, it's 99.9% upstream stuff
anyway. Lets start wider userbase testing.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This is backport of v5.6 patch.
Allwinner A64 SoC has separate supplies for PC, PD, PE, PG and PL. This
patch adds regulators for them to the pinctrl node.
Exception is PL which is used by the RSB bus. To avoid circular
dependencies, VCC-PL is omitted.
On boards with eMMC, VCC-PC is supplied by ELDO1, instead of DCDC1.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
There is a red LED marked as `GPIO_LED1` on the silkscreen and connected
to PE17, so use this LED for status signalization.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Specifications:
SoC: Allwinner A64 (1.2 GHz Quad-Core ARM Cortex-A53 64-bit)
RAM: 1GB or 2GB RAM DDR3L @ 672Mhz
Flash: 0/4/16GB eMMC flash memory for storage and boot
MicroSD card connector for cards up to 32GB
Debug: serial UART debug header with 0.1" pins
Wired connectivity: 10/100/1000Mbps GbE Ethernet
Wireless connectivity: on-board RTL8723BS 1T1R 802.11bgn WiFi and
Bluetooth 4.0 module with built-in antenna
(only available in the A64-OLinuXino-1G4GW)
Flashing instructions:
Standard sunxi SD card installation procedure - copy eMMC image to SD
card, insert in into SD card slot on the device and boot. You should see
something like following if the eMMC is detected correctly:
mmcblk2: mmc2:0001 P1XXXX 3.60 GiB
mmcblk2boot0: mmc2:0001 P1XXXX partition 1 16.0 MiB
mmcblk2boot1: mmc2:0001 P1XXXX partition 2 16.0 MiB
Then flash SD card eMMC image straight into the mmcblk2 device:
dd if=/mnt/openwrt...a64-olinuxino-emmc-squashfs-sdcard.img of=/dev/mmcblk2
It also possible to boot from boot0 partition[1]:
1. Compile U-Boot with CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0x40
otherwise the U-Boot will get stuck in bootloop
2. Configure eMMC to boot from boot0 partition inside U-Boot:
mmc bootbus 1 1 0 0; mmc partconf 1 1 1 0
3. echo 0 > /sys/block/mmcblk2boot0/force_ro
4. Write U-Boot from offset 0 (not offset 8k as with SD card) into
boot0 partition
dd if=u-boot-sunxi-with-spl.bin of=/dev/mmcblk2boot0
Known issues:
Wireless doesn't work properly via netifd.
1. https://linux-sunxi.org/index.php?title=Bootable_eMMC
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Specifications:
SoC: Allwinner A64 (1.2 GHz Quad-Core ARM Cortex-A53 64-bit)
RAM: 1GB or 2GB RAM DDR3L @ 672Mhz
Flash: 0/4/16GB eMMC flash memory for storage and boot
MicroSD card connector for cards up to 32GB
Debug: serial UART debug header with 0.1" pins
Wired connectivity: 10/100/1000Mbps GbE Ethernet
Wireless connectivity: on-board RTL8723BS 1T1R 802.11bgn WiFi and
Bluetooth 4.0 module with built-in antenna
(only available in the A64-OLinuXino-1G4GW)
Flashing instructions:
Standard sunxi SD card installation procedure - copy image to SD card,
insert in into SD card slot on the device and boot.
Known issues:
Wireless doesn't work properly via netifd.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Current boot script uses hardcoded bootdevice, which allows booting from
SD card only, so this patch allows booting directly from eMMC as well.
While at it, replace fixed root device with more flexible UUID based
probing, so from now on probing order of MMC device doesn't matter.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Adding U-Boot image for Olimex A64-Olinuxino eMMC, including patch which
adds eMMC boot partition configuration commands.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Rename the board as done in upstream commit 268ae6548779 ("sunxi: Rename
Sinovoip BPI M2 Plus to Bananapi M2 Plus H3") which backs the rename
with the following reasoning:
The brand Sinovoip is used for Sinovoip's original VOIP products, while
the Bananapi brand is for the single board computers they produce. This
has been verified by Bananapi. Rename the board from "Sinovoip BPI M2
Plus" to "Bananapi M2 Plus". For the defconfig file, all lowercase is
used.
To support the H5 variant of this board, the "H3" suffix is added to
the defconfig name.
This has to be done in order to allow building U-Boot past v2019.04
release where this change was introduced.
Ref: https://github.com/openwrt/openwrt/pull/2849#discussion_r396401489
Suggested-by: Pawel Dembicki <paweldembicki@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
U-boot also have defconfig for this board. In 2019.01 branch they are identical.
Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
In RouterBOARD parlance there never was an "art" partition.
This partition has always been named 'hard_config' on ar71xx.
This partition contains more than just ART (Atheros Radio Test) data. It
includes the hardware description (product code, serial, board
identifier, name, hardware options, MAC address), as well as other bits
affecting the operation of RouterBoot.
To avoid confusion with regular ART data, this partition is renamed in
line with historical ar71xx and ramips nomenclature as 'hard_config'.
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
[minor commit title/message adjustments]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
In RouterBOARD parlance there never was an "art" partition.
This partition has always been named 'hard_config' on ar71xx.
This partition contains more than just ART (Atheros Radio Test) data. It
includes the hardware description (product code, serial, board
identifier, name, hardware options, MAC address), as well as other bits
affecting the operation of RouterBoot.
To avoid confusion with regular ART data, this partition is renamed in
line with historical ar71xx and ramips nomenclature as 'hard_config'.
This commit fixes the previous support files and implements the nested
RouterBoot partition scheme as already used by ramips-based SPI-NOR
RouterBOARD DTSes, as previously reviewed and implemented in
bbe2cf657c ("ramips: fix RBM11G partitioning").
Tested-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
[minor commit title/message adjustments]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The Pogoplug E02 was not using the correct partitions
in device tree, but used the ones from upstream and
thus could not boot OpenWrt images.
In contrast, uboot-kirkwood is using the correct
partitions since d3fc4fbd74 ("uboot-kirkwood: re-add
Pogoplug E02 support").
This patch corrects the partitions in DTS for kernels
4.14, 4.19 and 5.4.
Fixes: 2b0fa00da8 ("kirkwood: add Pogoplug E02 Kernel support")
Signed-off-by: Alberto Bursi <bobafetthotmail@gmail.com>
Reviewed-by: Pawel Dembicki <paweldembicki@gmail.com>
Reviewed-by: Sungbo Eo <mans0n@gorani.run>
[commit title/message facelift, refresh 4.14 patch]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This commit adds support for the MT7622-based Elecom WRC-2533gent router,
with spi-nand storage and 512MB RAM.
The device has the following specifications:
* MT7622 (arm64 dual-core)
* 512MB RAM (DDR3)
* 4GB storage (spi-nand)
* 5x 1Gbps Ethernet (RTL8337C switch)
* 1x UART header
* 1x USB 3.0 port
* 5x LEDs
* 1x reset button
* 1x WPS button
* 1x slider switch
* 1x DC jack for main power (12V)
The following has been tested and is working:
* Ethernet switch
* 2.4g and 5g wifi
* USB 3.0 port
* sysupgrade
* buttons/leds
Not working:
* bluetooth firmware does not load even though it is present int he rootfs
Signed-off-by: John Crispin <john@phrozen.org>
the code would unconditionally tear down all interfaces upon a reconf.
This should only be done when the reconf call fails.
Signed-off-by: John Crispin <john@phrozen.org>
Release notes for 017:
Wave-1:
* March 19, 2020: Fix problem where power-save was not enabled when going off-channel to scan.
The problem was a boolean logic inversion in the chmgr code, a regression I introduced
a long time ago.
* March 19, 2020: When scanning only on current working channel, do not bother with disable/enable
powersave. This should make an on-channel scan less obtrusive than it was previously.
* March 23, 2020: Fix channel-mgr use-after-free problem that caused crashes in some cases. The crash
was exacerbated by recent power-save changes.
* March 23, 2020: Fix station-mode power-save related crash: backported the fix from 10.2 QCA firmware.
* March 23, 2020: Attempt to better clean up power-save objects and state, especially in station mode.
Release notes for 016:
Wave-1 changes, some debugging code for a crash someone reported, plus:
* February 28, 2020: Fix custom-tx path when sending in 0x0 for rate-code. Have tries == 0 mean
one try but NO-ACK (similar to how wave-2 does it).
wave-2:
* Fixed some long-ago regressions related to powersave and/or multicast. Maybe fix some
additional multicast and/or tx-scheduling bugs.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Acked-by: Petr Štetiar <ynezz@true.cz>
Use power led for device status.
The status led behavior has already been fixed in af28d8a539
("ath79: add support for GL.iNet GL-AR750S") when porting the
device to ath79. This fixes it for ar71xx as well.
Signed-off-by: Jan Alexander <jan@nalx.net>
[minor commit title/message adjustments]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This ports support for the TL-WA860RE v1 range extender from ar71xx
to ath79.
Specifications:
Board: AP123 / AR9341 rev. 3
Flash/RAM: 4/32 MiB
CPU: 535 MHz
WiFi: 2.4 GHz b/g/n
Ethernet: 1 port (100M)
Two external antennas
Flashing instructions:
Upload the factory image via the vendor firmware upgrade option.
Recovery:
Note that this device does not provide TFTP via ethernet like many
other TP-Link devices do. You will have to open the case if you
require recovery beyond failsafe.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Sebastian Knapp <sebastian4842@outlook.com>
This device seems to be identical to the TL-WDR4300, just with
different release date/region and TPLINK_HWID.
Support is added based on the ar71xx implementation.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Fix the test for an enabled sysntp initscript in dnsmasq.init, and get
rid of "test -o" while at it.
Issue reproduced on openwrt-19.07 with the help of pool.ntp.br and an
RTC-less ath79 router. dnssec-no-timecheck would be clearly missing
from /var/etc/dnsmasq.conf.* while the router was still a few days in
the past due to non-working DNSSEC + DNS-based NTP server config.
The fix was tested with the router in the "DNSSEC broken state": it
properly started dnsmasq in dnssec-no-timecheck mode, and eventually ntp
was able to resolve the server name to an IP address, and set the system
time. DNSSEC was then enabled by SIGINT through the ntp hotplug hook,
as expected.
A missing system.ntp.enabled UCI node is required for the bug to show
up. The reasons for why it would be missing in the first place were not
investigated.
Signed-off-by: Henrique de Moraes Holschuh <henrique@nic.br>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> [PKG_RELEASE increase]
Refer to shellcheck SC2166. There are just too many caveats that are
shell-dependent on test -a and test -o to use them.
Signed-off-by: Henrique de Moraes Holschuh <henrique@nic.br>
5e1bc34 ustream-openssl: clear error stack before SSL_read/SSL_write
f7f93ad add support for specifying usable ciphers
Also bump the ABI version since the layout of `struct ustream_ssl_ops`
changed.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
There is a restriction in the number of parameters(10) that may be passed to
the SetupHostCommand macro so continually adding explicit gcc'n' version
checks ends up breaking the compiler check for the later versions and
oddballs like Darwin as was done in 835d1c68a0 which added gcc10.
Drop all the explicitly specified gcc version checks. If a suitable gcc
compiler is not found, it may be specified at the dependency checking
stage after which that version will be symlinked into the build staging
host directory.
eg. 'CC=gccfoo CXX=g++foo make prereq'
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Acked-by: Jo-Philipp Wich <jo@mein.io>
In the geode subtarget all default x86 features were overwritten via :=
instead of extending them via +=.
This patch fixes the inheritance and thereby the compilation of
x86/geode target.
Compile tested x86/geode.
Signed-off-by: Paul Spooren <mail@aparcar.org>
The x86 image generation was refacted via cb007a7bf6 and accidently not
included `geode.mk` when selected as subtarget.
Now the file is included and image compilation for x86/geode works
again.
Thanks to Russell Senior <russell@personaltelco.net> for reporting the
problem and suggesting a patch!
Signed-off-by: Paul Spooren <mail@aparcar.org>
Lets add GCC 10 detection to the build system as distributions like Fedora 32 have started shipping with it.
Some tools like mtd-utils need work to compile under GCC10, but that will be next step.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Baptiste Jonglez
Petr Štetiar
Leon M. George
Aleksander Jan Bajkowski
Thibaut VARÈNE
Alberto Bursi
John Crispin
Rafał Miłecki
Álvaro Fernández Rojas
Hans Dedecker
Jan Alexander
Adrian Schmutzler
Henrique de Moraes Holschuh
Jo-Philipp Wich
Kevin Darbyshire-Bryant
Paul Spooren
Robert Marko