Currently all PCI devices get the same IRQ that affects performance badly.
This commit adresses this problem and cleans the code.
ar7100 has a special PCI interrupt controller@18060018 that works exactly
the same way as misc interrupt controller.
This patch does the following:
1. Defines pci-intc interrupt controller@18060018 in dtsi.
2. Removes interrupt-controller property from PCI node.
3. Sets a correct interrupt mask for PCI devices.
4. Removes all IRQ handling code from the PCI driver.
"qca,ar7100-misc-intc" should be used as the compatible property, becuase on ar7100
the controlled status register is read-only and the ack method used in
"qca,ar7240-misc-intc" won't work properly.
There are two very minor downsides of this patch that don't affect perormance:
1. We allocate an IRQ domain of 32 IRQ, whan we need only 5. But ar7100 aren't tiny un terms of RAM
and that is not very important and can be tuned if we implement "nr-interrupts" property".
2. It reuses the same irg chip name "MISC" for both controllers.
Run tested on DIR-825 B1.
Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com>
Without this patch you will get an error "gpio-export probe deferral
not supported" when you try to export i2c expander gpio pins.
gpio-export is probed long before i2c-bus and i2c expander are created
and it doesn't retry it so none pins are exported.
Signed-off-by: René van Dorst <opensource@vdorst.com>
apply the change to all instances of the gpio exports patch
Signed-off-by: Mathias Kresin <dev@kresin.me>
In the new DT-based pci-ar71xx driver, ar71xx_pci_irq_init() was being
called before populating the PCI controller's device_node struct member.
This led to no IRQ being assigned to connected PCI devices (e.g. ath9k
cards) and caused them to be non-functional aside from simply being
detected.
The previous errors encountered in dmesg were: "irq: no irq domain found
for /ahb/apb/pcie-controller@180c0000 !". /proc/interrupts listed an IRQ
of 0 for the cards.
While this has been only been tested on a yet-to-be-merged RouterStation
Pro target, it should also fix the broken wifi people have reported for
the ath79 WNDR3800 target.
Signed-off-by: Matt Merhar <mattmerhar@protonmail.com>
Check if the GPIO is valid (or set at all). If no GPIO is set in the
devicetree, a gpiolib related kernel warning + stacktrace is shown during
boot and gpio-export reports GPIOs as exported albeit none really is.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Add the missing enable and disable function.
Remove dummy mask and unmask function and use the one provided by
irq_dummy_chip.
Allow interrupt status register being defined from dts.
Add ddr_wb_flush for ar934x/qca953x.
Rename controller name to qca,ar9340-intc because this design was
first introduced in AR934x.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de>
Add support for the common led property "linux,default-trigger". It
allows to set a default led trigger via devicetree.
Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de>
[add commit message]
Signed-off-by: Mathias Kresin <dev@kresin.me>
This target aims to replace ar71xx mid-term. The big part that is still
missing is making the MMIO/AHB wifi work using OF. NAND and mikrotik
subtargets will follow.
Signed-off-by: John Crispin <john@phrozen.org>
John Crispin
Dmitry Tunin
Christian Lamparter
René van Dorst
Koen Vandeputte
Stijn Tintel
Matt Merhar
Mathias Kresin
Johann Neuhauser
Lucian Cristian