You cannot select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
92f83abc5e
6cafaca mt7603: use READ_ONCE instead of ACCESS_ONCE
9e2e0b8 mt76: round up length on mt76_wr_copy
e378ef1 mt76: mt7615: fix sparse warnings: warning: restricted __le16 degrades to integer
7991dd7 mt76: mt7615: introduce mt7615_regd_notifier
901a4c7 mt76: mt7615: add hw dfs pattern detector support
57c600e mt76: mt7615: do not perform txcalibration before cac is complited
6afc952 mt76: mt7615: add csa support
8919516 mt76: mt7615: add radar pattern test knob to debugfs
3be723c mt76: mt7615: clean up FWDL TXQ during/after firmware upload
47fe37e mt76: mt7615: fall back to sw encryption for unsupported ciphers
bc5e041 mt76: mt7603: enable hardware rate up/down selection
ae760db mt76: mt7615: move mt7615_mcu_set_rates to mac.c
2ae01f7 mt76: mt7615: reset rate index/counters on rate table update
6f98378 mt76: mt7615: sync with mt7603 rate control changes
edbe88e mt76: usb: fix endian in mt76u_copy
f43b622 mt76: usb: remove unneeded {put,get}_unaligned
5e1e5b7 mt76: usb: use full intermediate buffer in mt76u_copy
017d0ff mt76: mt76u: fix typo in mt76u_fill_rx_sg
2c0ccf1 mt76: mt7615: always release sem in mt7615_load_patch
0c6f1a2 mt76: mt7615: introduce mt7615_mcu_send_ram_firmware routine
3dfc1ee mt76: mt7615: fix sparse warnings: incorrect type in assignment (different base types)
9475320 mt76: mt7603: fix sparse warnings: warning: incorrect type in assignment (different base types)
e07451d mt76: mt7615: fix sparse warnings: warning: cast from restricted __le16
b973bef mt7603: do not use tssi-off power value for mt7628
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
5 years ago | |
|---|---|---|
| .github | 6 years ago | |
| config | 5 years ago | |
| include | 5 years ago | |
| package | 5 years ago | |
| scripts | 5 years ago | |
| target | 5 years ago | |
| toolchain | 5 years ago | |
| tools | 5 years ago | |
| .gitattributes | 12 years ago | |
| .gitignore | 6 years ago | |
| BSDmakefile | 18 years ago | |
| Config.in | 7 years ago | |
| LICENSE | 8 years ago | |
| Makefile | 6 years ago | |
| README | 6 years ago | |
| feeds.conf.default | 6 years ago | |
| rules.mk | 5 years ago | |
README
_______ ________ __
| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -__| || | | || _|| _|
|_______|| __|_____|__|__||________||__| |____|
|__| W I R E L E S S F R E E D O M
-----------------------------------------------------
This is the buildsystem for the OpenWrt Linux distribution.
To build your own firmware you need a Linux, BSD or MacOSX system (case
sensitive filesystem required). Cygwin is unsupported because of the lack
of a case sensitive file system.
You need gcc, binutils, bzip2, flex, python, perl, make, find, grep, diff,
unzip, gawk, getopt, subversion, libz-dev and libc headers installed.
1. Run "./scripts/feeds update -a" to obtain all the latest package definitions
defined in feeds.conf / feeds.conf.default
2. Run "./scripts/feeds install -a" to install symlinks for all obtained
packages into package/feeds/
3. Run "make menuconfig" to select your preferred configuration for the
toolchain, target system & firmware packages.
4. Run "make" to build your firmware. This will download all sources, build
the cross-compile toolchain and then cross-compile the Linux kernel & all
chosen applications for your target system.
Sunshine!
Your OpenWrt Community
http://www.openwrt.org