dumalogiya
/
openwrt
2
0
Fork 0
Code Issues Pull Requests Releases Wiki Activity

ath79: add support for TP-Link CPE610-v1

Browse Source 
TP-Link CPE610-v1 is an outdoor wireless CPE for 5 GHz with
one Ethernet port based on Atheros AR9344

Specifications:
 - Based on the same underlying hardware as the TP-Link CPE510
 - Power, LAN, WLAN5G green LEDs
 - 23dBi high-gain directional 2×2 MIMO antenna and a dedicated metal reflector

Flashing instructions:
 Flash factory image through stock firmware WEB UI
 or through TFTP
 To get to TFTP recovery just hold reset button while powering on for
 around 4-5 seconds and release.
 Rename factory image to recovery.bin
 Stock TFTP server IP:192.168.0.100
 Stock device TFTP adress:192.168.0.254

Signed-off-by: Andrew Cameron <apcameron@softhome.net>
master
Andrew Cameron 5 years ago committed by Christian Lamparter
parent 8a5a01a677
commit e15049c88b
5 changed files with 194 additions and 0 deletions
Show Stats Download Patch File Download Diff File

3
target/linux/ath79/base-files/etc/board.d/01_leds
Unescape Escape View File

@ -155,6 +155,9 @@ tplink,cpe210-v3)
ucidef_set_led_rssi "rssimediumhigh" "RSSIMEDIUMHIGH" "tp-link:green:link3" "wlan0" "60" "100"
ucidef_set_led_rssi "rssihigh" "RSSIHIGH" "tp-link:green:link4" "wlan0" "80" "100"
;;
tplink,cpe610-v1)
ucidef_set_led_netdev "lan" "LAN" "tp-link:green:lan" "eth0"
;;
tplink,re450-v2)
ucidef_set_led_netdev "lan_data" "LAN Data" "tp-link:green:lan_data" "eth0" "tx rx"
ucidef_set_led_netdev "lan_link" "LAN Link" "tp-link:green:lan_link" "eth0" "link"

1
target/linux/ath79/base-files/etc/board.d/02_network
Unescape Escape View File

@ -25,6 +25,7 @@ ath79_setup_interfaces()
pqi,air-pen|\
tplink,cpe210-v2|\
tplink,cpe210-v3|\
tplink,cpe610-v1|\
tplink,re350k-v1|\
tplink,re450-v2|\
tplink,tl-mr10u|\

140
target/linux/ath79/dts/ar9344_tplink_cpe610-v1.dts
Unescape Escape View File

@ -0,0 +1,140 @@
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
/dts-v1/;
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
#include "ar9344.dtsi"
/ {
model = "TP-Link CPE610 v1";
compatible = "tplink,cpe610-v1", "qca,ar9344";
aliases {
led-boot = &system;
led-failsafe = &system;
led-upgrade = &system;
};
leds {
compatible = "gpio-leds";
system: lan {
label = "tp-link:green:lan";
gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
};
wlan5g {
label = "tp-link:green:wlan5g";
gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
linux,default-trigger = "phy0tpt";
};
};
keys {
compatible = "gpio-keys";
reset {
linux,code = <KEY_RESTART>;
gpios = <&gpio 4 GPIO_ACTIVE_LOW>;
debounce-interval = <60>;
};
};
};
&ref {
clock-frequency = <40000000>;
};
&uart {
status = "okay";
};
&spi {
num-cs = <1>;
status = "okay";
flash@0 {
compatible = "jedec,spi-nor";
reg = <0>;
spi-max-frequency = <25000000>;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
uboot: partition@0 {
label = "u-boot";
reg = <0x000000 0x020000>;
read-only;
};
partition@20000 {
label = "partition-table";
reg = <0x020000 0x010000>;
read-only;
};
info: partition@30000 {
label = "info";
reg = <0x030000 0x010000>;
read-only;
};
partition@40000 {
label = "firmware";
reg = <0x040000 0x780000>;
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
label = "kernel";
reg = <0x000000 0x1c0000>;
};
partition@1c0000 {
label = "rootfs";
reg = <0x1c0000 0x5c0000>;
};
};
partition@7c0000 {
label = "config";
reg = <0x7c0000 0x030000>;
read-only;
};
art: partition@7f0000 {
label = "art";
reg = <0x7f0000 0x010000>;
read-only;
};
};
};
};
&wmac {
status = "okay";
mtd-cal-data = <&art 0x1000>;
mtd-mac-address = <&info 0x08>;
};
&eth0 {
status = "okay";
mtd-mac-address = <&info 0x08>;
phy-mode = "mii";
phy-handle = <&swphy4>;
};
&eth1 {
status = "okay";
compatible = "syscon", "simple-mfd";
};

11
target/linux/ath79/image/generic-tp-link.mk
Unescape Escape View File

@ -146,6 +146,17 @@ define Device/tplink_cpe210-v3
endef
TARGET_DEVICES += tplink_cpe210-v3
define Device/tplink_cpe610-v1
$(Device/tplink-safeloader)
ATH_SOC := ar9344
IMAGE_SIZE := 7680k
DEVICE_TITLE := TP-Link CPE610 v1
TPLINK_BOARD_ID := CPE610V1
LOADER_TYPE := elf
KERNEL := kernel-bin | append-dtb | lzma | loader-kernel
endef
TARGET_DEVICES += tplink_cpe610-v1
define Device/tplink_archer-d50-v1
ATH_SOC := qca9531
DEVICE_TITLE := TP-Link Archer D50 v1

39
tools/firmware-utils/src/tplink-safeloader.c
Unescape Escape View File

@ -278,6 +278,45 @@ static struct device_info boards[] = {
.first_sysupgrade_partition = "os-image",
.last_sysupgrade_partition = "support-list",
},
/** Firmware layout for the CPE610V1 */
{
.id = "CPE610V1",
.vendor = "CPE610(TP-LINK|UN|N300-5|00000000):1.0\r\n",
.support_list =
"SupportList:\r\n"
"CPE610(TP-LINK|EU|N300-5|00000000):1.0\r\n"
"CPE610(TP-LINK|EU|N300-5|45550000):1.0\r\n"
"CPE610(TP-LINK|EU|N300-5|55530000):1.0\r\n"
"CPE610(TP-LINK|UN|N300-5|00000000):1.0\r\n"
"CPE610(TP-LINK|UN|N300-5|45550000):1.0\r\n"
"CPE610(TP-LINK|UN|N300-5|55530000):1.0\r\n"
"CPE610(TP-LINK|US|N300-5|55530000):1.0\r\n"
"CPE610(TP-LINK|UN|N300-5):1.0\r\n"
"CPE610(TP-LINK|EU|N300-5):1.0\r\n"
"CPE610(TP-LINK|US|N300-5):1.0\r\n",
.support_trail = '\xff',
.soft_ver = NULL,
.partitions = {
{"fs-uboot", 0x00000, 0x20000},
{"partition-table", 0x20000, 0x02000},
{"default-mac", 0x30000, 0x00020},
{"product-info", 0x31100, 0x00100},
{"signature", 0x32000, 0x00400},
{"os-image", 0x40000, 0x1c0000},
{"file-system", 0x200000, 0x5b0000},
{"soft-version", 0x7b0000, 0x00100},
{"support-list", 0x7b1000, 0x00400},
{"user-config", 0x7c0000, 0x10000},
{"default-config", 0x7d0000, 0x10000},
{"log", 0x7e0000, 0x10000},
{"radio", 0x7f0000, 0x10000},
{NULL, 0, 0}
},
.first_sysupgrade_partition = "os-image",
.last_sysupgrade_partition = "support-list",
},
{
.id = "WBS210",

Write Preview
Loading…
Cancel
Save