You cannot select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
Tomasz Maciej Nowak 3a3d998c12 layerscape: resurrect support for FRDM-LS1012A
Re-add support for NXP FRDM-LS1012A, which mimics the flash layout of the
rest boards supported by LSDK.

0x000000000000-0x000000100000 : "bl2"
0x000000100000-0x000000500000 : "fip"
0x000000500000-0x000000600000 : "u-boot-env"
0x000000600000-0x000000a00000 : "reserved-1"
0x000000a00000-0x000000d00000 : "pfe"
0x000000d00000-0x000000f00000 : "reserved-2"
0x000000f00000-0x000001000000 : "dtb"
0x000001000000-0x000002000000 : "kernel"
0x000002000000-0x000004000000 : "ubifs"

Specification
SoC: LS1012A single core 800MHz
RAM: 512 MB DDR3
Flash: 64 MB QSPI NOR
Ethernet: 2x 10/100/1000 Mbps
Connectors: µUSB 3.0 OTG
            µUSB 2.0 (debugging & power input)
            2x 3.5mm jack for microphone & headphone (SGTL5000)
            Arduino Shield expansion with I2C, SPI, UART, and GPIO
            JTAG
LEDS: 3x (non-configurable)
Buttons: 1x (reset, non-configurable)

Be advised that erasing or writing 64MB flash takes some time to finish.
Do not reset the board until all operations end with success, otherwise
You'll need external tools to re-program the flash chip.

Installation
Follow the QSPI programing procedure for LS1012AFRWY board in
target/linux/layerscape/README, point 3.3.
Don't forget about updating U-Boot environment with MAC addresses of
ethernet interfaces, variable 'ethaddr' for eth0 and 'eth1addr' for eth1.

As the LSDK images do not support sysupgrade, nor do changes in this
commit, it's planed in upcoming submissions.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
4 years ago
..
ls1012afrdm-uEnv.txt layerscape: resurrect support for FRDM-LS1012A 4 years ago
ls1012afrwy-uEnv.txt layerscape: add ls1012afrwy support and drop ls1012afrdm 6 years ago
ls1012ardb-uEnv.txt layerscape: convert to use TF-A for firmware 5 years ago
ls1021aiot-sdboot-uEnv.txt layerscape: add LS1021AIOT board support 6 years ago
ls1021atwr-sdboot-uEnv.txt layerscape: add SD card boot support 6 years ago
ls1021atwr-uEnv.txt layerscape: add armv7 subtarget and ls1021atwr board support 6 years ago
ls1043ardb-sdboot-uEnv.txt layerscape: add SD card boot support 6 years ago
ls1043ardb-uEnv.txt layerscape: convert to use TF-A for firmware 5 years ago
ls1046ardb-sdboot-uEnv.txt layerscape: add SD card boot support 6 years ago
ls1046ardb-uEnv.txt layerscape: convert to use TF-A for firmware 5 years ago
ls1088ardb-sdboot-uEnv.txt layerscape: add SD card boot support 6 years ago
ls1088ardb-uEnv.txt layerscape: convert to use TF-A for firmware 5 years ago
ls2088ardb-uEnv.txt layerscape: convert to use TF-A for firmware 5 years ago