The device label shows the address currently assigned to the OpenWrt
LAN interface.
Current setup is:
LAN *:b8 factory 0xe006 label
WAN *:b7 factory 0xe000
For vendor FW bootlog we get (manually removed parts of the address):
[ 7.520000] set LAN/WAN LWLLL
[ 7.530000] GMAC1_MAC_ADRH -- : 0x00004031
[ 7.530000] GMAC1_MAC_ADRL -- : 0x3c****b7
[ 7.530000] GDMA2_MAC_ADRH -- : 0x00004031
[ 7.540000] GDMA2_MAC_ADRL -- : 0x3c****b8
[ 7.540000] eth1: ===> VirtualIF_open
Without further information, this does not allow verification of
the currently unexpected LAN/WAN assignment (we would expect 0xe000
to be LAN).
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
ipTIME A8004T is a 2.4/5GHz band AC2600 router, based on Mediatek
MT7621A.
Specifications:
- SoC: MT7621A
- RAM: DDR3 256M
- Flash: SPI NOR 16MB
- WiFi:
- 2.4GHz: MT7615E
- 5GHz: MT7615E
- Ethernet: 5x 10/100/1000Mbps
- Switch: SoC internal
- USB: 1 * USB3.0 port
- UART:
- J4: 3.3V, TX, RX, GND (3.3V is the square pad) / 57600 8N1
- Other info:
- J9: Unknown unpopulated header.
Installation via web interface:
1. Flash **initramfs** image through the stock web interface.
2. Boot into OpenWrt and perform sysupgrade with sysupgrade image.
Revert to stock firmware:
1. Perform sysupgrade with stock image.
Signed-off-by: Yong-hyu Ban <perillamint@quendi.moe>
[do not enable xhci node in DTS which is already enabled in DTSI]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Edimax RA21S is a dual band 11ac router,
based on MediaTek MT7621A and MT7615N chips.
Specification:
- SoC: MediaTek MT7621A dual-core @ 880MHz
- RAM: 256M (Nanya NT5CC128M16IP)
- FLASH: 16MB (Macronix MX25L12835F)
- WiFi: 2.4/5 GHz 4T4R
- 2.4GHz MediaTek MT7615N bgn
- 5GHz MediaTek MT7615N nac
- Switch: SoC integrated Gigabit Switch (4 x LAN, 1 x WAN)
- USB: No
- BTN: Reset, WPS
- LED: 4 red LEDs, indistinguishable when case closed
- UART: through-hole on PCB.
J1: 3.3V - RX - GND - TX / 57600-8N1. 3.3V is the square pad
Installation:
Update the factory image via the OEM web-interface
(by default: http://192.168.2.1/)
User: admin
Password: 1234
The sysupgrade image can be installed via TFTP
from the U-Boot bootloader. Connect via ethernet port 2.
Tested on device by @UAb5eSMn
Signed-off-by: Maksym Medvedev <redrathnure@gmail.com>
[split DTS and take over improvements from RG21S, extend commit
message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The device label contains:
E01: 74:4D:28:xx:xx:30
E05: 74:4D:28:xx:xx:34
The first value corresponds to the address set in hard_config 0x10.
That one is taken for the label MAC address.
Signed-off-by: Sven Roederer <freifunk@it-solutions.geroedel.de>
So far, lan/wan MAC address for Edimax RG21S are only read using
mtd_get_mac_ascii, so eth0.1 and eth0.2 addresses are set, but
eth0 address is random. Since the device's LAN address is the same
as for 2.4 GHz, though, this patch set's the eth0 address based
on the 2.4 GHz one, which can be extracted by mtd-mac-address.
This will also allow to move the label MAC address setup to DT.
The setup of lan_mac and wan_mac are kept in 02_network, so those
locations are still in use, too.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The Edimax RG21S has a label which bears two MAC addresses:
2.4 GHz (n) and 5 GHz (n+1)
The complete MAC address setup is as follows:
2.4 GHz *:83 factory 0x4, u-boot-env wlanaddr
5 GHz *:84 factory 0x8004
LAN *:83 u-boot-env ethaddr
WAN *:85 u-boot-env wanaddr
Since 2.4 GHz is the first address on the label and the same
as used for ethernet, take this one for label MAC address.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
JCG JHR-AC876M is an AC2600M router
Hardware specs:
SoC: MT7621AT
2.4GHz: MT7615N 4x4 @ PCIe0
5GHz: MT7615N 4x4 @ PCIe1
Flash: Winbond W25Q128JVSQ 16MiB
RAM: Nanya NT5CB128M16 256MiB
USB 2.0 and 3.0 ports
6 LEDs, 3 of which are connected to SoC GPIO
Reset and WPS buttons
Flash instructions:
Stock to OpenWrt:
Upload factory.bin in stock firmware's upgrade page,
do not preserve settings
OpenWrt to stock:
Push and hold the reset button for 5s while power cycling to
enter recovery mode;
Visit 192.168.1.1 and upload stock firmware
MAC addresses map:
0x0004 *:1c wlan2g/wan/label
0x8004 *:20 wlan5g
0xe000 *:1b lan
0xe006 *:1a not used in stock fw
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
ipTIME A6ns-M is a 2.4/5GHz band AC1900 router, based on MediaTek MT7621A.
Specifications:
- SoC: MT7621AT
- RAM: DDR3 128MB
- Flash: SPI NOR 16MB
- WiFi:
- 2.4GHz: MT7615
- 5GHz: MT7615
- Ethernet: 5x 10/100/1000Mbps
- Switch: SoC internal
- UART:
- J4: 3.3V, TX, RX, GND (3.3V is the square pad) / 57600 8N1
Installation via web interface:
1. Flash **initramfs** image through the stock web interface.
2. Boot into OpenWrt and perform sysupgrade with sysupgrade image.
Revert to stock firmware:
1. Perform sysupgrade with stock image.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
ZIO FREEZIO is a 2.4/5GHz band AC1200 router, based on MediaTek MT7621A.
Specifications:
- SoC: MT7621AT
- RAM: DDR3 128MB
- Flash: SPI NOR 16MB
- WiFi:
- 2.4GHz: MT7603EN
- 5GHz: MT7612EN
- Ethernet: 5x 10/100/1000Mbps
- Switch: SoC internal
- USB: 1x 3.0
- UART:
- J4: 3.3V, RX, TX, GND (3.3V is the square pad) / 57600 8N1
Notes:
- FREEZIO has almost the same board as WeVO W2914NS v2.
- Stock firmware is based on OpenWrt BB.
MAC addresses in factory partition:
0x0004: WiFi 2.4GHz (label_mac-8)
0x002e: WAN (label_mac)
0x8004: WiFi 5GHz (label_mac-4)
0xe000: LAN (label_mac+1)
Installation via web interface:
1. Access web admin page and turn on "OpenWrt UI mode".
2. Flash sysupgrade image through LuCI, with the "Keep settings" option
OFF.
Revert to stock firmware:
1. Perform sysupgrade with stock image.
Make sure to NOT preserve settings.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[rebase, use mt7621_wevo_w2914ns-v2.dtsi]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The device label contains:
E01: B8:69:F4:xx:xx:07
E02: B8:69:F4:xx:xx:09
The first value corresponds to the address set in hard_config 0x10.
That one is taken for the label MAC address.
Thanks to Martin Schiller for retrieving the information.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This uses the flash locations instead of eth0 MAC address to
calculate MAC address increments for WAN.
The change will make the MAC address setup of a particular device
more obvious and removes the dependency of 02_network on the eth0
initialization.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The evaluation boards do not set up a MAC address for eth0
in the first place, so it does not make sense to calculate a WAN
address from the random MAC used there.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The switch LAN port numbers are in reversed order with original config.
With this patch they are fixed.
Port order checked on both devices.
Signed-off-by: Gabor Varga <vargagab@gmail.com>
[merged definitions into appropriate block, extended commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The Mikrotik RBM33G has only 2 LAN ports.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
[moved node in 02_network to maintain alphabetic sorting]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
ALFA Network Quad-E4G is a universal Wi-Fi/4G platform, which offers
three miniPCIe (PCIe, USB 2.0, SIM) and a single M.2 B-key (dual-SIM,
USB 3.0) slots, RTC and five Gigabit Ethernet ports with PoE support.
Specification:
- MT7621A (880 MHz)
- 256/512 MB of RAM (DDR3)
- 16/32+ MB of FLASH (SPI NOR)
- optional second SPI flash (8-pin WSON/SOIC)
- 1x microSD (SDXC) flash card reader
- 5x 10/100/100 Mbps Ethernet, with passive PoE support (24 V) in LAN1
- optional 802.3at/af PoE module for WAN
- 3x miniPCIe slot (with PCIe and USB 2.0 buses, micro SIM and 5 V)
- 1x M.2/NGFF B-key 3042 (USB 3.0/2.0, mini + micro SIM)
- RTC (TI BQ32002, I2C bus) with backup battery (CR2032)
- external hardware watchdog (EM Microelectronic EM6324)
- 1x USB 2.0 Type-A
- 1x micro USB Type-B for system serial console (Holtek HT42B534)
- 11x LED (5 for Ethernet, 5 driven by GPIO, 1x power indicator)
- 3x button (reset, user1, user2)
- 1x I2C (4-pin, 2.54 mm pitch) header on PCB
- 4x SIM (6-pin, 2.00 mm pitch) headers on PCB
- 2x UART2/3 (4-pin, 2.54 mm pitch) headers on PCB
- 1x mechanical power switch
- 1x DC jack with lock (24 V)
Other:
- U-Boot selects default SIM slot, based on value of 'default_sim' env
variable: '1' or unset -> SIM1 (mini), '2' -> SIM2 (micro). This board
has additional logic circuit for M.2 SIM switching. The 'sim-select'
will work only if both SIM slots are occupied. Otherwise, always slot
with SIM inside is selected, no matter 'sim-select' value.
- U-Boot enables power in all three miniPCIe and M.2 slots before
loading the kernel
- this board supports 'dual image' feature (controlled by 'dual_image'
U-Boot environment variable)
- all three miniPCIe slots have additional 5 V supply on pins 47 and 49
- the board allows to install up to two oversized miniPCIe cards (vendor
has dedicated MediaTek MT7615N/D cards for this board)
- this board has additional logic circuit controlling PERSTn pins inside
miniPCIe slots. By default, PERSTn (GPIO19) is routed to all miniPCIe
slots but setting GPIO22 to high allows PERSTn control per slot, using
GPIO23-25 (value is inverted)
You can use the 'sysupgrade' image directly in vendor firmware which is
based on OpenWrt (make sure to not preserve settings - use 'sysupgrade
-n -F ...' command). Alternatively, use web recovery mode in U-Boot:
1. Power the device with reset button pressed, the modem LED will start
blinking slowly and after ~3 seconds, when it starts blinking faster,
you can release the button.
2. Setup static IP 192.168.1.2/24 on your PC.
3. Go to 192.168.1.1 in browser and upload 'sysupgrade' image.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
This replaces all uses of $(cat /sys/class/ieee80211/phyX/macaddress)
by retrieval from the proper flash locations. This will make
02_network independent of WiFi setup again.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
As started in 19724e28c8 ("ramips: split base-files into
subtargets"), this moves some smaller left-over files to the
appropriate base-files folder of their subtarget:
- /etc/init.d/bootcount
- /etc/uci-defaults/04_led_migration
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
- remove WAN port index
- load WAN MAC address directly from the flash
- provide label MAC address
- increase flash's SPI frequency to 80MHz
- add mt76 led nodes to make WiFi LEDs work
- drop unnecessary pinmux groups
The factory partition scheme for MAC addresses (verified on both devices):
0x4 : WiFi 2.4GHz (label_mac-9)
0x28 : unused
0x2e : WAN (label_mac)
0x8004: WiFi 5GHz (label_mac-5)
0xe000: LAN (label_mac-1)
0xe006: unused
By improving flash speed,
`time dd if=/dev/mtdblock3 of=/dev/null bs=64k`
has been reduced from 14.51s to 3.11s.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[rebased]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
So far, MAC address assignment in ramips has contained a default
case, which defined wan_mac = eth0 + 1 for _every_ device not
having an explicit case there.
This is not desirable, as many device supporters will just not
care or know about this definition, so another MAC address will be
introduced by accident. In some cases the wan_mac is assigned
although it is not needed, in other cases even addresses not
dedicated to the device will be used (e.g. wan_mac actually is
eth0 - 1, but during support nobody cared, so eth0 + 1 is used now,
which might actually belong to another device ...).
Thus, in this PR the former default case is converted to an
explicit case. This one comprises all devices not being accounted
for by other cases, reduced by those not having wan at all.
The big number of entries for this node might be another indication
that many of them wouldn't actually be there if there hadn't been
default wan_mac setup.
In exchange, the current "do nothing" case can be removed, as it
will be the new default case.
The devices being put in the newly created explicit case were
determined as follows:
1. Create a list of all devices based on the DTS files.
2. Remove all devices already having an explicit entry setting
their address.
3. Remove all devices that only have lan set up in the first part
of 02_network:
mt7620:
- alfa-network,tube-e4g
- asus,rp-n53
- buffalo,wmr-300
- comfast,cf-wr800n
- edimax,ew-7476rpc
- edimax,ew-7478ac
- elecom,wrh-300cr
- hnet,c108
- kimax,u25awf-h1
- kimax,u35wf
- kingston,mlw221
- kingston,mlwg2
- microduino,microwrt
- netgear,ex2700
- netgear,ex3700
- netgear,wn3000rp-v3
- planex,cs-qr10
- planex,mzk-ex300np
- planex,mzk-ex750np
- ravpower,wd03
- sercomm,na930
- yukai,bocco
- zbtlink,zbt-cpe102
- zte,q7
mt7621:
- gnubee,gb-pc1
- gnubee,gb-pc2
- linksys,re6500
- mikrotik,rbm11g
- netgear,ex6150
- thunder,timecloud
- tplink,re350-v1
- tplink,re650-v1
mt76x8:
- alfa-network,awusfree1
- d-team,pbr-d1
- glinet,vixmini
- vocore,vocore2-lite
- tama,w06
- tplink,tl-mr3020-v3
- tplink,tl-wa801nd-v5
- tplink,tl-wr802n-v4
- tplink,tl-wr902ac-v3
- vocore,vocore2
- widora,neo-16m
- widora,neo-32m
rt288x:
- buffalo,wli-tx4-ag300n
- dlink,dap-1522-a1
rt305x:
- allnet,all0256n-4m
- allnet,all0256n-8m
- allnet,all5002
- allnet,all5003
- alphanetworks,asl26555-16m
- alphanetworks,asl26555-8m
- asus,wl-330n
- aximcom,mr-102n
- dlink,dcs-930
- easyacc,wizard-8800
- hame,mpr-a2
- hootoo,ht-tm02
- huawei,d105
- intenso,memory2move
- planex,mzk-dp150n
- rt305x dlink,dcs-930l-b1
- sparklan,wcr-150gn
- tenda,3g150b
- tenda,3g300m
- tenda,w150m
- trendnet,tew-638apb-v2
- unbranded,a5-v11
- vocore,vocore-16m
- vocore,vocore-8m
- wansview,ncs601w
- zorlik,zl5900v2
rt3883:
- loewe,wmdr-143n
- omnima,hpm
4. Put the remaining devices in the new case.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This patch does the following:
1. remove u-boot-env partition
Stock bootloader saves env variables at 0x80000 in flash,
and there is nothing stored at 0x30000.
By merging the partition "u-boot-env" with "u-boot",
the partition table becomes the same as used in stock firmware:
00000000-00080000: "Bootloader"
00080000-00100000: "Config"
00100000-00140000: "Factory"
00140000-07f80000: "Kernel"
2. fix LAN/WAN MAC addresses and provide label MAC address
Ethernet MAC addresses are stored in factory partition at:
0xe000: LAN (label_mac)
0xe006: WAN (label_mac+1)
3. fix LAN port order
WF-2881 LAN ports are in reverse order of switch ports.
4. fix WiFi LEDs
mt76 led nodes are added to make WiFi LEDs work.
On top of this, mt76 node names are changed to more generic ones,
and compatible strings are also added.
5. fix pinmux groups
uart3 and uart2 pins are used as button and led, but jtag pins are not.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
While most of the target's contents are split into subtargets, the
base-files are maintained for the target as a whole.
However, OpenWrt already implements a mechanism that will use (and
even prefer) files in the subtargets' directories. This can be
exploited to make several scripts subtarget-specific and thus save
some space.
In certain cases, keeping files in parent (=target) base-files was
more convenient, and thus no splitting was performed for those.
Note that this will increase overall code lines, but reduce code
per subtarget.
base-files ipk size reduction:
master (mt7621) 60958 B
split (mt7620) 46358 B (- 14.3 kiB)
split (mt7621) 48759 B (- 11.9 kiB)
split (mt76x8) 44948 B (- 15.6 kiB)
split (rt288x) 43508 B (- 17.0 kiB)
split (rt305x) 45616 B (- 15.0 kiB)
split (rt3883) 44176 B (- 16.4 kiB)
Run-tested on:
GL.iNet GL-MT300N-V2 (mt76x8)
D-Link DWR-116 (mt7620)
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This removes _all_ occurrences of kmod-usb-core from
DEVICE_PACKAGES and similar variables.
This package is pulled as dependency by one of the following
packages in any case:
- kmod-usb-chipidea
- kmod-usb-dwc2
- kmod-usb-ledtrig-usbport
- kmod-usb-ohci
- kmod-usb2
- kmod-usb2-pci
- kmod-usb3
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
[remove kmod-usb-core from EnGenius ESR600]
Signed-off-by: David Bauer <mail@david-bauer.net>
Revert "mac80211: add new minstrel_ht patches to improve probing on mt76x2" (9861050b85)
Revert "kernel: use bulk free in kfree_skb_list to improve performance" (98b654de2e)
Revert "ramips: add preliminary support for WIO ONE" (085141dc5b)
Revert "ramips: add preliminary support for SGE AP-MTKH7-0006 developer board" (b1db6d0539)
Revert "build: use config.site generated by autoconf-lean, drop hardcoded sitefiles" (363ce4329d)
Revert "toolchain: add autoconf-lean" (fdb30eed03)
Revert "build: allow overriding the filename on the remote server when downloading" (6fa0e07758)
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Upstream kernel added support for RAW_APPENDED_DTB on ralink arch
in the following commit:
02564fc89d3d ("ralink: Introduce fw_passed_dtb to arch/mips/ralink")
Use upstream solution and get rid of our OWRTDTB hack.
This commit set DEVICE_DTS to $$(DTS) instead of replacing DTS with
DEVICE_DTS in device profile because DTS variable will be dropped
in later commits.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
[Tested on mt7621/mt76x8]
Tested-by: Chuanhong Guo <gch981213@gmail.com>
[Tested on rt305x/mt7620]
Tested-by: INAGAKI Hiroshi <musashino.open@gmail.com>
It's no longer needed as all mt7621 devices use DT binding (supported by
upstream mtd code) for specifying "firmware" part format explicitly.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This commit adds support for the Mikrotik RouterBOARD RBM33g.
=Hardware=
The RBM33g is a mt7621 based device featuring three gigabit ports, 2
miniPCIe slots with sim card sockets, 1 M.2 slot, 1 USB 3.0 port and a male
onboard RS-232 serial port. Additionally there are a lot of accessible
GPIO ports and additional buses like i2c, mdio, spi and uart.
==Switch==
The three Ethernet ports are all connected to the internal switch of the
mt7621 SoC:
port 0: Ethernet Port next to barrel jack with PoE printed on it
port 1: Innermost Ethernet Port on opposite side of RS-232 port
port 2: Outermost Ethernet Port on opposite side of RS-232 port
port 6: CPU
==Flash==
The device has two spi flash chips. The first flash chips is rather small
(512 kB), connected to CS0 by default and contains only the RouterBOOT
bootloader and some factory information (e.g. mac address).
The second chip has a size of 16 MB, is by default connected to CS1 and
contains the firmware image.
==PCIe==
The board features three PCIe-enabled slots. Two of them are miniPCIe
slots (PCIe0, PCIe1) and one is a M.2 (Key M) slot (PCIe2).
Each of the miniPCIe slots is connected to a dedicated mini SIM socket
on the back of the board.
Power to all three PCIe-enabled slots is controlled via GPIOs on the
mt7621 SoC:
PCIe0: GPIO9
PCIe1: GPIO10
PCIe2: GPIO11
==USB==
The board has one external USB 3.0 port at the rear. Additionally PCIe
port 0 has a permanently enabled USB interface. PCIe slot 1 shares its
USB interface with the rear USB port. Thus only either the rear USB port
or the USB interface of PCIe slot 1 can be active at the same time. The
jumper next to the rear USB port controls which one is active:
open: USB on PCIe 1 is active
closed: USB on rear USB port is active
==Power==
The board can accept both, passive PoE and external power via a 2.1 mm
barrel jack. The input voltage range is 11-32 V.
=Installation=
==Prerequisites==
A USB -> RS-232 Adapter and a null modem cable are required for
installation.
To install an OpenWRT image to the device two components must be built:
1. A openwrt initramfs image
2. A openwrt sysupgrade image
===initramfs & sysupgrade image===
Select target devices "Mikrotik RBM33G" in
openwrt menuconfig and build the images. This will create the images
"openwrt-ramips-mt7621-mikrotik_rbm33g-initramfs-kernel.bin" and
"openwrt-ramips-mt7621-mikrotik_rbm33g-squashfs-sysupgrade.bin" in the output
directory.
==Installing==
**Make sure to back up your RouterOS license in case you do ever want to
go back to RouterOS using "/system license output" and back up the created
license file.**
Serial settings: 115200 8N1
The installation is a two-step process. First the
"openwrt-ramips-mt7621-mikrotik_rbm33g-initramfs-kernel.bin" must be booted
via tftp:
1. Set up a dhcp server that points the bootfile to tftp server serving
the "openwrt-ramips-mt7621-mikrotik_rbm33g-initramfs-kernel.bin"
initramfs image
2. Connect to WAN port (left side, next to sys-LED and power indicator)
3. Connect to serial port of board
4. Power on board and enter RouterBOOT setup menu
5. Set boot device to "boot over ethernet"
6. Set boot protocol to "dhcp protocol" (can be omitted if DHCP server
allows dynamic bootp)
6. Save config
7. Wait for board to boot via Ethernet
On the serial port you should now be presented with the OpenWRT boot log.
The next steps will install OpenWRT persistently.
1. Copy "openwrt-ramips-mt7621-mikrotik_rbm33g-squashfs-sysupgrade.bin" to the device
using scp.
2. Write openwrt to flash using "sysupgrade
openwrt-ramips-mt7621-mikrotik_rbm33g-squashfs-sysupgrade.bin"
Once the flashing completes reboot the router and let it boot from flash.
It should boot straight to OpenWRT.
Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
Define USB port power on/off GPO as voltage regulator type instead of
exposing as a normal GPIO.
The GPO is now controlled by the USB driver via the voltage regulator
definition. The regulator is of fixed output type (5V for USB) hence the
GPO switches power on/off to USB pin 1 (Vcc)
USB port power is enabled on driver load and disabled on driver unload.
Enable kernel support for fixed voltage regulator types on mt7621.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
- removed upstreamed patches
- 0901-spansion_nand_id_fix.patch is disabled, not clear if it's needed
Signed-off-by: Roman Yeryomin <roman@advem.lv>
Signed-off-by: John Crispin <john@phrozen.org>
The kernel 4.4 patches where already removed with the bump to 4.9. Drop
the the subtarget configs as well.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The TP-Link RE350 is a wall-wart AC1200 range extender/access point with
a single gigabit ethernet port and two non-detachable antennas, based on
the MT7621A SoC with MT7603E and MT7612E radios.
Firmware wise it is very similar to the QCA based RE450.
SoC: MediaTek MT7621A (880MHz)
Flash: 8MiB (Winbond W25Q64)
RAM: 64MiB (DDR2)
Ethernet: 1x 1Gbit
Wireless: 2T2R 2.4Ghz (MT7603E) and 5GHz (MT7612E)
LEDs: Power, 2.4G, 5G (blue), WPS (red and blue), ethernet link/act
(green)
Buttons: On/off, LED, reset, WPS
Serial header at J1, 57600 8n1:
Pin 1 TX
Pin 2 RX
Pin 3 GND
Pin 4 3.3V
Factory image can be uploaded directly through the stock UI.
Signed-off-by: Alex Maclean <monkeh@monkeh.net>
CONFIG_SG_POOL symbol is selected only by CONFIG_SCSI, since the last
one is disabled by default then disable CONFIG_SG_POOL by default too.
And explicitly enable it only for platforms that use CONFIG_SCSI.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
In order to have a smaller initramfs image remove all packages not
needed on all devices and add them explicitely for those actually
needing them. Also remove wpad-mini from ramips default package set
and add it to all sub-targets except for MT7621.
While at it reorder packages alphabetically and replace kmod-mt76 with
kmod-mt7603 and/or kmod-mt76x2 depending on the chip actually used on
a specific board.
Hopefully fixes FS#758
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
I made a commit that added the RTC driver to the kernel config with
the intent that it would fix hctosys. Unfortunately while the RTC
driver is in there, it's connected through I2C, the driver for which
comes in module form and is thus loaded late. After this commit, it
works fine.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Build the RTC driver into the kernel, (and remove the optional module), in order
to make hctosys working. (Currently the module is loaded after hctosys has failed previously)
Signed-off-by: Rosen Penev <rosenp@gmail.com>
This makes init.d script handle existing UCI entries using the new
trigger. It also switches all targets to use its package.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
The D-Link DIR-860L B1 has a flash chip which doesn't support
4K sectors. Since the DIR-860L B1 was the only mt7621 board which had
the 4k blocksize set, the 4K sector support is removed from the kernel
config.
I've checked the flash chips of all boards having set a 4K blocksize
again. This time I searched harder to finding bootlogs instead of
relying on wikis articles and/or the device tree source file.
The Planex MZK-DP150N has an en25q32b instead of the mentioned one in
the dts. Albeit the en25q32b supports 4K sectors, 4K support is not
enabled in the driver. Change the blocksize for this board back to 64K.
Reported-by: Russell Senior <russell@personaltelco.net>
Signed-off-by: Mathias Kresin <dev@kresin.me>
DENG Qingfang
Adrian Schmutzler
Yong-hyu Ban
Maksym Medvedev
Sven Roederer
Sungbo Eo
Gabor Varga
Martin Schiller
Piotr Dymacz
Felix Fietkau
Chuanhong Guo
Rafał Miłecki
Tobias Schramm
Kevin Darbyshire-Bryant
Roman Yeryomin
Mathias Kresin
Alex Maclean
John Crispin
Stijn Tintel
Sergey Ryazanov
Daniel Golle
Paul Spooren
Rosen Penev