CONFIG_SG_POOL symbol is selected only by CONFIG_SCSI, since the last
one is disabled by default then disable CONFIG_SG_POOL by default too.
And explicitly enable it only for platforms that use CONFIG_SCSI.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Fixes these prints on boot:
[ 13.785600] imx-uart 2020000.serial: DMA transaction error.
[ 13.793134] imx-uart 2020000.serial: DMA transaction error.
[ 13.798721] imx-uart 2020000.serial: DMA transaction error.
Based on following upstream patch by Tim Harvey (Gateworks):
80a01b6582
TX complete DMA messages are getting missed.
This is also currently an issue in mainline.
For now we will disable DMA in serial/imx.c.
This resolves an issue encountered with RS485 transmit.
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
The IMX6 PCIe host controller does not fire legacy interrupts if MSI is
enabled. A patch is being worked on to enable MSI at runtime only when
it is needed but meanwhile this patch will disable MSI for the imx6 kernel.
This fixes the no interrupt issue on cards/drivers that use legacy interrupts
such as ath9k.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
The MV88E6176 switch is present on the GW16083 and the GW5904
As of a5c32a1f19 these drivers are to be
enabled static in per-target kernels.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
If a 'fixfdt' uboot script exists, execute it prior to bootm to allow
easy bootloader env based fdt fixups and tweaks
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Bump kernel to 4.4.44. Compile-tested on ar71xx, ramips/mt7621 and x86/64.
.44 has been run-tested on the 17.01 branch here on ar71xx and mt7621.
Signed-off-by: Stijn Segers <francesco.borromini@inventati.org>
Fixes the same hctosys init issue as described in commit
5481ce9a11
The Gateworks Ventana family uses an emulated Dallas 1672
RTC device.
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Otherwise if we use ds1307 as kernel module, hctosys fails as ds1307 is
being initialized later then hctosys:
[ 2.427349] hctosys: unable to open rtc device (rtc0)
[ 3.714263] snvs_rtc 20cc000.snvs:snvs-rtc-lp: rtc core: registered 20cc000.snvs:snvs-r as rtc1
[ 8.990061] rtc-ds1307 3-006f: rtc core: registered mcp7941x as rtc0
Signed-off-by: Petr Štetiar <ynezz@true.cz>
In dc92917 there was introduced login.sh wrapper which allows
configuration of console passwords via UCI system ttylogin config
option.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Only add them where they are actually required.
Should help with compatibility issues with stock U-Boot images that
access UBI
Signed-off-by: Felix Fietkau <nbd@nbd.name>
commit a2386c384d requires the
module to be static in the kernel.
So lets actually add support for it inside the kernel config.
Tested on Ventana
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
The Gateworks Ventana GW553x is a single-board computer based on the NXP
IMX6 SoC with the following features:
* IMX6 DualLite Soc (supports IMX6S,IMX6DL,IMX6Q)
* small form factor (35x70mm)
* 512MB DDR3 DRAM (2x32bit) (options up to 2GB)
* 256MB NAND flash (4GB option)
* Gateworks System Controller:
- hardware watchdog
- hardware monitor
- pushbutton controller
- EEPROM storage
- power control
* JTAG programmable
* 1x miniPCI socket (with PCIe, USB, SIM)
* 1x microSD socket
* 1x SIM socket
* Inertial Module (LSM9DS1 9DOF: 3x acc, 3x rate, 3x mag)
* analog CVBS video in
* GPS (optional uBlox EVA-M8M)
* Application headers:
- 2x TTL UART (TX/RX)
- 4x TTL GPIO (3x configurable as PWM)
- 3x CVBS Analog video input (1x decoder with 3x selectable inputs)
* Front panel connectors:
* micro-HDMI audio/video out
- 1x user programmable LED
- 1x configurable user pushbutton
- 1x USB OTG
See http://www.gateworks.com for more info
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Point to correct devices when booting from msata or MMC
Changes fetched from Gateworks git
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
[Jo-Philipp Wich: rebased to apply against current LEDE version]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The image builder does not bundle sub-directories within $(KERNEL_BUILD_DIR),
therfore the intermediate "ventana-uImage.boot" directory is not shipped,
leading to failures with "make image" later on.
To circumvent the issue, store the intermediate boot files as tar archive
instead of putting them into a directory to ensure that they end up in the
final image builder tarball. Fixes FS#102
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Fix ubifs mkfs options
Use standard Build/* commands instead of doing everything in the hackish
ubi-boot-overlay template
Fix bootfs.tar.gz build error
Signed-off-by: Felix Fietkau <nbd@nbd.name>
It is used by a core build template, so the variable should be
initialized and added to DEVICE_VARS in the core.
Same for DEVICE_DTS_DIR
Signed-off-by: Felix Fietkau <nbd@nbd.name>
In order to create a bootable block storage device, both bootfs and rootfs
tarballs are required. However, our current scheme does not export a bootfs
tarball so add the packaging of it here.
Signed-off-by: Pushpal Sidhu <psidhu@gateworks.com>
SVN-Revision: 49196
Change the name of the .ubi produced to strip out the word 'factory'. This is
mainly due to the fact that there is no difference between the Ventana 'factory'
image vs the standard image.
Name changes from:
openwrt-imx6-ventana-squashfs.nand-factory_<size>.ubi to
openwrt-imx6-ventana-squashfs-nand_<size>.ubi
Signed-off-by: Pushpal Sidhu <psidhu@gateworks.com>
SVN-Revision: 48016
Some Ventana boards have a Marvell sky2 GigE controller as eth1 however
assigning the mac address through device-tree is difficult because the
PCI slot can move around depending on board configuration and slot population.
To work around this we add a patch to the sky2 driver to allow accessing its
mac address via a device-tree alias.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Pushpal Sidhu <psidhu@gateworks.com>
SVN-Revision: 48013
On Ventana boards the Gateworks System Controller is the only device on I2C1
(/dev/i2c-0) and it can NAK transfers if it is busy in an ADC loop. Because
this is a multi-function device with several slave addresses it is best to
add retries at the controller level instead of within each slave driver. This
adds a patch that adds 3 retries for i2c transactions only for Ventana boards
and only for I2C1
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Pushpal Sidhu <psidhu@gateworks.com>
SVN-Revision: 48012
This is a backport of a2291badc355d58ead5c19ae0609468947416040 from thermal-soc
accepted upstream.
The IMX6Q/IMX6DL SoC's have a 2-bit temperature grade stored in OTP. Instead
of assuming 85C for passive cooling threshold and 100C for critical base
these thresholds off the thermal gade max CPU temperature:
- passive threshold: max - 10C
- critical threshold: max - 5C
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
SVN-Revision: 48011
Certain board revisions of the GW52xx support an SPI host controller with
a single chip-select going to an off board connector.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Pushpal Sidhu <psidhu@gateworks.com>
SVN-Revision: 48009
Replace former uci-defaults.sh implementation with the uci-defaults-new.sh one
and update all users accordingly.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47867
Removed video related kernel params that are only appropriate for the
Freescale downstream vendor kernel and not appriate for mainline linux.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
SVN-Revision: 47532
The 206-ARM-imx-ventana-added-GW16083-to-device-tree.patch merged wrong in
the conversion from 3.18 to 4.1. This patch resolves that and puts the
device-tree nodes in the correct place.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
SVN-Revision: 47510
Replace the ventana ubi images from a single rootfs volume containing the
rootfs as well as kernel+dtbs in the boot/ subdir to a multi-volume ubi
containing kernel+dtbs+bootscript in 'root' ubifs volume, rootfs in 'rootfs'
squasfs volume, and rootfs_data an empty ubifs volume.
At the same time move ventana image creation over to using the new
TARGET_DEVICE syntax as a cleanup.
Additionally removed FIT image creation as it is recommended that this be
done manually to produce signed FIT images if needed.
Note that a bootscript is needed for Ventana to change its default mtdparts
to rename the 2nd partition from 'rootfs' to 'ubi'. This is because there
are patches in OpenWrt kernels that try to auto-attach and auto-mount and these
get in the way if the mtd partition is named 'rootfs'.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
SVN-Revision: 47508
Upstream patch: e9d6d6b62f306ba83e1441af5daf2809a6167474
Add support for the Gateworks GW5510 board featuring:
* i.MX6 SoC
* up to 512MB DDR3
* up to 2GB NAND flash
* 1x miniPCIe socket (with USB)
* HDMI out (micro-HDMI)
* HDMI in (micro-HDMI) (currently supported by only vendor kernel)
* TTL level I/O (supported by GW16111 breakout board):
* I2C
* 2x UART
* CAN
* 2x DIO (GPIO/PWM)
* USB OTG
Also add support to OpenWrt build system
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Pushpal Sidhu <psidhu@gateworks.com>
SVN-Revision: 47505
It was wrong anyway, missing file sort order parameter which was fixed
in base month ago.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
SVN-Revision: 47312
We're in process of cleaning nand_do_platform_check. Currently is leaves
a special mark in /tmp/sysupgrade-nand-path triggering some diffent code
path in nand_upgrade_stage1. This can be a bit confusing.
The plan is to have the check function only check the image and nothing
else. Then platform code (platform_pre_upgrade) should trigger NAND
specific upgrade path. This is what this patch implements.
This follows ar71xx, lantiq and partially bcm53xx.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 46944
Disable ARCH_NEEDS_CPU_IDLE_COUPLED by-default in generic config, since
only one platfrom (omap) needs them.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 44614
HAMRADIO enabled in all generic configs, but no one platform directly
use related drivers/protocols. This symbol is only used for kmod-ax25
package modules. Furthermore, half of platforms explicitly disables
this symbol, what silently disables build of modules for kmod-ax25
package.
So disable HAMRADIO by-default in generic config, add it to kmod-ax25
package and remove it from platform specific configs.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 44613
CONFIG_GENERIC_NET_UTILS is selected by CONFIG_NET and already enabled
in generic config, so we don't need this symbol in platform specific
configurations.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 44611
Koen Vandeputte
Mathias Kresin
Stijn Tintel
Sergey Ryazanov
Felix Fietkau
Tim Harvey
Hauke Mehrtens
Stijn Segers
Petr Štetiar
Álvaro Fernández Rojas
Jo-Philipp Wich
John Crispin
John Crispin
Luka Perkov
John Crispin
Felix Fietkau
Jo-Philipp Wich
Rafał Miłecki
Jonas Gorski