This patch ports the cybertan_part code from ar71xx and converts the
driver to a DT-supported mtd parser. As a result, it will no longer
add the u-boot, nvram and art partitions, which were never part of
the special Cybertan header.
Instead these partitions have to be specified in the DT, which has the
upside of making it possible to add properties (i.e.: read-only), labels
and references to these important partitions.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Currently it's close to impossible to tell what part of mac80211 setup
went wrong. Errors logged into system log look like this:
radio0 (6155): command failed: No error information (-524)
radio0 (6155): command failed: Not supported (-95)
radio0 (6155): command failed: I/O error (-5)
radio0 (6155): command failed: Too many open files in system (-23)
With this commit change it's getting clear:
command failed: No error information (-524)
Failed command: iw dev wlan0 del
command failed: Not supported (-95)
Failed command: iw phy phy0 set antenna_gain 0
command failed: I/O error (-5)
Failed command: iw phy phy0 set distance 0
command failed: Too many open files in system (-23)
Failed command: iw phy phy0 interface add wlan0 type __ap
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
The board is made by Avnet, so rename it accordingly as
upstream has done it
Also move the device to maintain alphabetic order
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Implement the generation of sdcard images with ext4 or
squashfs + f2fs overlay, but only enable the latter
automatically
Additionally, add mkf2fs and e2fsprogs to default packages
to manipulate ext4 and f2fs filesystems
Finally, disable the automatic generation of initramfs
and rootfs.tar.gz images, as they are no longer required
(they can still be selected in menuconfig)
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Use options from generic instead of target-specific,
as the bootargs are now passed by the bootloader
and can be device-specific
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Follow the strategy of other targets and create a
default environment file, uEnv.txt, to configure the
behavior of U-Boot.
For now, use it to pass bootargs to the kernel
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Create a directory inside STAGING_DIR and copy U-Boot
output images, so they can be used later when creating the
sdcard image
Additionally, like others targets, override the default
install method to avoid copying the images to bin directory
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Select the U-Boot variant automatically based on the
current selected device, and hide the package from
menuconfig
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
The board was added when creating the target, but the
corresponding device was never defined inside the target
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Refresh patches
Changes since latest bump:
af3bd07 Man page typo.
d682099 Picky changes to 47b45b2967c931fed3c89a2e6a8df9f9183a5789
47b45b2 Fix lengths of interface names
2b38e38 Minor improvements in lease-tools
282eab7 Mark die function as never returning
c346f61 Handle ANY queries in context of da8b6517decdac593e7ce24bde2824dd841725c8
03212e5 Manpage typo.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
When Package/xx/conffiles only contains directories that are empty at
package time, conffiles.resolved will be missing and the following
error messages will appear in the build log.
/home/yousong/git-repo/openwrt/openwrt/scripts/ipkg-build -c -o 0 -g 0 /home/yousong/git-repo/openwrt/openwrt/build_dir/target-mips_24kc_musl/linux-malta_be/openvswitch-2.10.0/ipkg-mips_24kc/openvswitch-common /home/yousong/git-repo/openwrt/openwrt/bin/packages/mips_24kc/packages
mv: cannot stat 'CONTROL/conffiles.resolved': No such file or directory
chmod: cannot access 'CONTROL/conffiles': No such file or directory
It will not break the ipkg-build process. The change is merely cosmetic
to not cause confusion when reading logs
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
The need arises from building Open vSwitch kernel datapath modules, e.g.
- kmod-openvswitch from Linux upstream
- kmod-openvswitch-intree from openvswitch source code
where both provides virtual package "kmod-openvswitch" for userspace
packages to select and depend on
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Allowing DHCPV6_CLIENT_FQDN and DHCPV6_ACCEPT_RECONFIGURE to be turned off.
Defaulting to false, former behavior remains unchanged.
Signed-off-by: pacien <pacien.trangirard@pacien.net>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> [PKG_RELEASE increase]
The bump to 4.14 changed the way mdio probes behind switches.
While the board_info is added to the list, the code that actually inserted
the list info into the phydev structure was missing.
This resulted in non-working ethernet ports.
Re-add it to fix switch probing.
This mimics the exact behaviour as it was in kernel 4.9.
Before:
[ 1.066007] switch0: Atheros AR8327 rev. 4 switch registered on ag71xx-mdio.0
[ 1.073409] Atheros AR8216/AR8236/AR8316: probe of ag71xx-mdio.0:00 failed with error -22
[ 1.102455] libphy: ag71xx_mdio: probed
[ 1.737938] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.0:00 [uid=004dd034, driver=Generic PHY]
[ 1.747994] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:RGMII
[ 2.377642] ag71xx-mdio.1: Found an AR934X built-in switch
[ 2.429938] eth1: Atheros AG71xx at 0xba000000, irq 5, mode:GMII
After:
[ 11.163357] libphy: Fixed MDIO Bus: probed
[ 11.319898] libphy: ag71xx_mdio: probed
[ 11.360844] switch0: Atheros AR8327 rev. 4 switch registered on ag71xx-mdio.0
[ 12.447398] libphy: ag71xx_mdio: probed
[ 13.077402] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.0:00 [uid=004dd034, driver=Atheros AR8216/AR8236/AR8316]
[ 13.088989] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:RGMII
[ 13.717716] ag71xx-mdio.1: Found an AR934X built-in switch
[ 13.769990] eth1: Atheros AG71xx at 0xba000000, irq 5, mode:GMII
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
*** Changes in GDB 8.2
Support for the following target has been added:
RiscV ELF (riscv*-*-elf)
Support for following targets and native configurations has been removed:
m88k running OpenBSD (m88*-*-openbsd*)
SH-5/SH64 ELF (sh64-*-elf*)
SH-5/SH64 (sh*)
SH-5/SH64 running GNU/Linux (sh*-*-linux*)
SH-5/SH64 running OpenBSD (sh*-*-openbsd*)
Various Python API enhancements
Aarch64/Linux enhancements:
SVE support.
Hardware watchpoints improvements for entities stored at unaligned addresses.
New "c" response to disable the pager for the rest of the current command.
C expressions can now use _Alignof, and C++ expressions can now use alignof.
Improved flexibility for loading symbol files.
The 'info proc' command nows works on running processes on FreeBSD systems as well as core files created on FreeBSD systems.
A new --enable-codesign=CERT configure option to automatically codesign GDB after build (useful on MacOS X).
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
*** Changes in GDB 8.2
Support for the following target has been added:
RiscV ELF (riscv*-*-elf)
Support for following targets and native configurations has been removed:
m88k running OpenBSD (m88*-*-openbsd*)
SH-5/SH64 ELF (sh64-*-elf*)
SH-5/SH64 (sh*)
SH-5/SH64 running GNU/Linux (sh*-*-linux*)
SH-5/SH64 running OpenBSD (sh*-*-openbsd*)
Various Python API enhancements
Aarch64/Linux enhancements:
SVE support.
Hardware watchpoints improvements for entities stored at unaligned addresses.
New "c" response to disable the pager for the rest of the current command.
C expressions can now use _Alignof, and C++ expressions can now use alignof.
Improved flexibility for loading symbol files.
The 'info proc' command nows works on running processes on FreeBSD systems as well as core files created on FreeBSD systems.
A new --enable-codesign=CERT configure option to automatically codesign GDB after build (useful on MacOS X).
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
TP-Link TL-MR3020 v3 is a pocket-size router based on MediaTek MT7628N.
This PR is based on the work of @meyergru[1], with his permission.
Specification:
- MediaTek MT7628N/N (575 Mhz)
- 64 MB of RAM
- 8 MB of FLASH
- 2T2R 2.4 GHz
- 1x 10/100 Mbps Ethernet
Flash instruction:
The only way to flash the image in TL-MR3020 v3 is to use
tftp recovery mode in U-Boot:
1. Configure PC with static IP 192.168.0.225/24 and tftp server.
2. Rename "openwrt-ramips-mt76x8-tplink_tl-mr3020-v3-squashfs-tftp-recovery.bin"
to "tp_recovery.bin" and place it in tftp server directory.
3. Connect PC with the LAN port, press the reset button, power up
the router and keep button pressed for around 6-7 seconds, until
device starts downloading the file.
4. Router will download file from server, write it to flash and reboot.
[1] https://github.com/meyergru/lede-source/commits/TL-MR3020-V3
Signed-off-by: Carlo Nel <carlojnel@gmail.com>
Without "syscon" being present in an ag71xx ethernet DT node's
compatible property, a panic occurs at boot during probe citing
"Unhandled kernel unaligned access".
With this modification, the panic no longer occurs and instead the probe
simply fails, allowing the boot process to continue.
Signed-off-by: Matt Merhar <mattmerhar@protonmail.com>
This adds "syscon" to the compatible properties for the eth0/eth1 nodes
in ar7100.dtsi.
Without this, a kernel panic is encountered on boot with some ar7100
boards. This for some reason wasn't an issue for the WNDR3800, which
uses a Realtek switch chipset, but the panic was encountered on the
RouterStation Pro (using an AR8216 switch) and some other boards that
haven't yet been merged.
The panic message mentions an unaligned access and happens in
ag71xx_mdio_probe in drivers/net/ethernet/atheros/ag71xx/ag71xx_mdio.c.
Even if the unaligned access is fixed, the ag71xx_mdio probe still fails
without the "syscon" property.
This was already being worked around in
ar7161_ubnt_routerstation-pro.dts by overriding the compatible property,
so this commit removes that as well.
All of the other ath79 .dtsi already have this property, so no changes
are needed elsewhere.
Signed-off-by: Matt Merhar <mattmerhar@protonmail.com>
The pinmux for all SoCs using this driver is now set via the pinmux. It
makes this code obsolete.
Some of the code targeting the mt76x8 SoCs is still required. The sd
card pins share the pads with the EPHY. These pads need to be switched
to digital mode if the pins are used for sd cards.
The eMMC 8-bit mode has to be enabled via pinmux instead of a kernel
option. The uart2 group need to be set to function "sdxc d5 d4", pwm1
to "sdxc d6" and pwm0 to "sdxc d7" to do so. It can't be done by as
part of a default pinmux, as it would break the normal operation of
uart2.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Set the pins to the required mode via the pinmux driver. It allows to
get rid of the pinmux related code in the sd card driver.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Drop the nd_sd gpio pinmux in case sdcard is used. They're mutually
exclusive and for most of the boards not even used as GPIOs.
If the pins are in sdcard mode, the pins ND_WE_N and ND_CS_N are still
GPIOs (#45 and #46).
Signed-off-by: Mathias Kresin <dev@kresin.me>
The rt3352 has a pin that can be used as second spi chip select,
watchdog reset or GPIO. The pinmux setup was missing the definition of
said pin but it is already used in the SoC dtsi.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The dnsmasq variants should provide dnsmasq, otherwise it is impossible
to include them in the image.
This change allows one to have CONFIG_PACKAGE_dnsmasq=m and
CONFIG_PACKAGE_dnsmasq-full=y, e.g. because you want DNSSEC support, or
IPSETs suport on your 3000-devices fleet ;-)
Signed-off-by: Henrique de Moraes Holschuh <henrique@nic.br>
Refresh patches
Remove 240-ubus patch as upstream accepted.
Add uci option ubus which allows to enable/disable ubus support (enabled
by default)
Upstream commits since last bump:
da8b651 Implement --address=/example.com/#
c5db8f9 Tidy 7f876b64c22b2b18412e2e3d8506ee33e42db7c
974a6d0 Add --caa-record
b758b67 Improve logging of RRs from --dns-rr.
9bafdc6 Tidy up file parsing code.
97f876b Properly deal with unaligned addresses in DHCPv6 packets.
cbfbd17 Fix broken DNSSEC records in previous.
b6f926f Don't return NXDOMAIN to empty non-terminals.
c822620 Add --dhcp-name-match
397c050 Handle case of --auth-zone but no --auth-server.
1682d15 Add missing EDNS0 section. EDNS0 section missing in replies to EDNS0-containing queries where answer generated from --local=/<domain>/
dd33e98 Fix crash parsing a --synth-domain with no prefix. Problem introduced in 2.79/6b2b564ac34cb3c862f168e6b1457f9f0b9ca69c
c16d966 Add copyright to src/metrics.h
1dfed16 Remove C99 only code.
6f835ed Format fixes - ubus.c
9d6fd17 dnsmasq.c fix OPT_UBUS option usage
8c1b6a5 New metrics and ubus files.
8dcdb33 Add --enable-ubus option.
aba8bbb Add collection of metrics
caf4d57 Add OpenWRT ubus patch
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
As of version 4.21, strace enforces mpers by default. The current
implementation of aarch64 compat in strace assumes it's identical to
ARMv7 EABI and therefore tries to enable m32 personality support. As
there is no -m32 support on aarch64, this causes the build to fail.
Restore previous strace behavior to fix build on aarch64.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Tested-by: Karl Palsson <karlp@tweak.net.au>
u-boot.mk checks for the Default profile to build images for all targets.
This brings the target default profile in sync with other targets
Signed-off-by: Felix Fietkau <nbd@nbd.name>
* Kconfig: use new-style help marker
* global: run through clang-format
* uapi: reformat
* global: satisfy check_patch.pl errors
* global: prefer sizeof(*pointer) when possible
* global: always find OOM unlikely
Tons of style cleanups.
* crypto: use unaligned helpers
We now avoid unaligned accesses for generic users of the crypto API.
* crypto: import zinc
More style cleanups and a rearrangement of the crypto routines to fit how this
is going to work upstream. This required some fairly big changes to our build
system, so there may be some build errors we'll have to address in subsequent
snapshots.
* compat: rng_is_initialized made it into 4.19
We therefore don't need it in the compat layer anymore.
* curve25519-hacl64: use formally verified C for comparisons
The previous code had been proved in Z3, but this new code from upstream
KreMLin is directly generated from the F*, which is preferable. The
assembly generated is identical.
* curve25519-x86_64: let the compiler decide when/how to load constants
Small performance boost.
* curve25519-arm: reformat
* curve25519-arm: cleanups from lkml
* curve25519-arm: add spaces after commas
* curve25519-arm: use ordinary prolog and epilogue
* curve25519-arm: do not waste 32 bytes of stack
* curve25519-arm: prefix immediates with #
This incorporates ASM nits from upstream review.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
PCI paths of the WLAN devices have changed between kernel 4.4 and 4.9;
migrate config so existing wifi-iface definitions don't break.
This is implemented as a hotplug handler rather than a uci-defaults script
as the migration script must run before the 10-wifi-detect hotplug handler.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
A buffer is split into multiple descriptors if it exceeds 16 KB.
Apply the same split for the skb head as well (to deal with corner cases
on fraglist support)
Signed-off-by: Felix Fietkau <nbd@nbd.name>
9d843334 Update bash_completion
23cb3f38 Update manual pages
1d682dcd Bump up version number to 1.33.0, LT revision to 31:0:17
601fbbb4 Update doc
f44aa246 Update AUTHORS
dd74a6dd Update manual pages
e959e733 src: Refactor utos
fb9a204d nghttpx: Fix compile error without mruby
cd096802 Update doc
7417fd71 nghttpx: Per-pattern not per-backend
2d1a981c Merge branch 'akonskarm-master'
45acc922 clang-format
214d0899 Merge branch 'master' of https://github.com/akonskarm/nghttp2 into akonskarm-master
31fd707d nghttpx: Fix broken healthmon frontend
9a2e38e0 fix code for reuse addr on asio client
d24527e7 Bump up LT revision due to v1.32.1 release
6195d747 nghttpx: Share mruby context if it is compiled from same file
fb97f596 nghttpx: Allocate mruby file because fopen requires NULL terminated string
0ccc7a77 nghttpx: Move blocked request data to request buffer for API request
32826466 nghttpx: Fix crash with API request
0422f8a8 nghttpx: Fix worker process crash with neverbleed write error
e329479a Merge pull request #1215 from nghttp2/mruby-per-backend
f80a7873 Merge branch 'akonskarm-reuse_addr'
866ac6ab add option reuse addr in local endpoint configuration of asio client
b574ae6a nghttpx: Support per-backend mruby script
de4fd7cd doc: Update doc
32d7883c nghttpx: Downstream::request_buf_full: take into account blocked_request_buf_
9b24e197 nghttpx: Choose h1 protocol if headers have been sent to backend on retry
13ffece1 Merge pull request #1214 from nghttp2/fix-rst-without-dconn
9d5b781d Fix stream reset if data from client is arrived before dconn is attached
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
CAKE supports overriding of its internal classification of
packets through the tc filter mechanism.
Update the man page in our package, even though we don't
build them. Someone may find the documentation useful.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
(cherry picked from commit 30598a05385b0ac2380dd4f30037a9f9d0318cf2)
Christian Lamparter
Rafał Miłecki
Rosen Penev
Luis Araneda
Hans Dedecker
Daniel Engberg
Yousong Zhou
pacien
Koen Vandeputte
Carlo Nel
Matt Merhar
Mathias Kresin
Henrique de Moraes Holschuh
Stijn Tintel
Felix Fietkau
Jason A. Donenfeld
Matthias Schiffer
Alexander Couzens
Kevin Darbyshire-Bryant