All definitions of gpio in SoC DTSI files do not set status, i.e.
have it enabled. This drops all remaining redundant "status = okay"
definitions in descendent files (mostly older ones).
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
In ath79, for several SoCs the console bootargs are defined to the
very same value in every device's DTS. Consolidate these definitions
in the SoC dtsi files and drop further redundant definitions elsewhere.
The only device without any bootargs set has been OpenMesh OM5P-AC V2.
This will now inherit the setting from qca955x.dtsi
Note that while this tidies up master a lot, it might develop into a
frequent pitfall for backports.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
These boards suffer from a sudden inability to establish a link on the
SGMII. Enable the workaround to fix the link when it dies.
Signed-off-by: David Bauer <mail@david-bauer.net>
There are at least 3 different chips in the Scorpion series of SoCs.
Rename the common DTSI to better reflect it's purpose for the whole
series.
Also rename the compatible bindings from qca,ar9557 and qca,qca9557
to qca,qca9550.
Signed-off-by: David Bauer <mail@david-bauer.net>
The hack-patch which introduced the "at803x-disable-smarteee" for
disabling SmartEEE did in fact not disable SmartEEE but rather disabled
802.3az "standard" EEE.
This can be done by using the upstream properties "eee-broken-100tx" and
"eee-broken-1000t". EEE is then disabled by the PHY subsystem.
Tested on devolo WiFi pro 1200e.
Signed-off-by: David Bauer <mail@david-bauer.net>
The "/dts-v1/;" identifier is supposed to be put once at the beginning
of a device tree file. Thus, it makes no sense to provide it a second
time in to-be-included DTSI files.
This removes the identifier from all DTSI files in /target/linux.
Most of the DTS files in OpenWrt do contain the "/dts-v1/;". It is
missing for most of the following targets, though:
mvebu, ipq806x, mpc85xx, ipq40xx
This does not touch ipq806x for now, as the bump to 4.19 is close.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This applies several style adjustments that have been requested in
recent reviews to older DTS files. Despite making the code base more
consistent, this will also help to reduce review time when DTSes
are copy/pasted.
Applied changes:
- Rename gpio-keys/gpio-leds to keys/leds
- Remove node labels that are not used
- Use label property for partitions
- Prefix led node labels with "led_"
- Remove redundant includes
- Harmonize new lines after status property
- Several smaller style fixes
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Upstream commit 6d4cd04 changes how the internal delays of the AR803x
based PHYs are enabled. With this commit, all internal delays are
disabled on driver probe and enabled based on the 'phy-mode' property in
the device-tree.
Before this commit, the RX delay was always enabled upon soft-reset
while the TX delay retained it's previous state. A hard reset enabled
the RX delay while the TX delay was disabled.
Because of this inconsistency, wrongly specified PHY-modes were working
correctly while the hardware was in a different state.
Fix the PHY-modes of some affected devices (and clean up misplaced
properties along the way) to keep the devices working flawlessly with
kernels >= 5.1.
Signed-off-by: David Bauer <mail@david-bauer.net>
Hardware
--------
CPU: Qualcomm Atheros QCA9558
RAM: 128M DDR2
FLASH: 16MiB
ETH: 1x Atheros AR8035 (PoE in)
1x Atheros AR8033
WiFi2: QCA9558 2T2R
WiFi5: QCA9880 2T2R
BTN: 1x Reset
LED: 1x LED blue
1x LED red
BEEP: 1x GPIO attached piezo beeper
UART: 3.3V GND TX RX (115200-N-8) (3.3V is square pad)
Header is located next to reset-button
Installation
------------
Make sure you set a password for the root user as prompted on first
setup!
1. Upload OpenWRT sysupgrade image via SSH to the device.
Use /tmp as the destination folder on the device.
User is root, password the one set in the web interface.
2. Install OpenWRT with
> sysupgrade -n -F /tmp/<openwrt-image-name>
Signed-off-by: David Bauer <mail@david-bauer.net>
Adrian Schmutzler
David Bauer