This commit creates the ath79/mikrotik subtarget in order to support
MikroTik devices based on Qualcomm Atheros MIPS SoCs.
MikroTik devices need a couple of specific features: the split MiNOR
firmware MTD format, which is not used by other devices, and the 4k
sector erase size on SPI NOR storage, which can not be added to the
ath79/generic and ath79/nand subtargets now.
Additionally, the commit moves the two MikroTik devices already in
the generic and nand subtargets to this new one.
Tested on the RB922 board and the wAP AC router.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Sitecom WLR-8100 v1 002 (marketed as X8 AC1750) is a dual band wireless
router.
Specification:
- Qualcomm Atheros SoC QCA9558
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (Macronix MX25L12845EMI-10G - SPI NOR)
- 5x 10/100/1000 Mbps Ethernet
- 3T3R 2.4 GHz (QCA9558 WMAC)
- 3T3R 5.8 Ghz (QCA9880-BR4A)
- 1x USB 3.0 (Etron EJ168A)
- 1x USB 2.0
- 9x LEDs
- 2x GPIO buttons
Everything working.
Installation and restore procedure tested
Installation
1. Connect to one of LAN (yellow) ethernet ports,
2. Open router configuration interface,
3. Go to Toolbox > Firmware,
4. Browse for OpenWrt factory image with dlf extension and hit Apply,
5. Wait few minutes, after the Power LED will stop blinking, the router
is ready for configuration.
Restore OEM FW (Linux only)
1. Download OEM FW from website (tested with WLR-8100v1002-firmware-v27.dlf)
2. Compile the FW for this router and locate the "mksenaofw" tool
in build_dir/host/firmware-utils/bin/ inside the OpenWrt buildroot
3. Execute "mksenaofw -d WLR-8100v1002-firmware-v27.dlf -o WLR-8100v1002-firmware-v27.dlf.out" where:
WLR-8100v1002-firmware-v27.dlf is the path to the input file
(use the downloaded file)
WLR-8100v1002-firmware-v27.dlf.out is the path to the output file
(you can use the filename you want)
4. Flash the new WLR-8100v1002-firmware-v27.dlf.out file. WARNING: Do not keep settings.
Additional notes.
The original firmware has the following button configuration:
- Press for 2s the 2.4GHz button: WPS for 2.4GHz
- Press for 2s the 5GHz button: WPS for 5GHz
- Press for 15s both 2.4GHz and 5GHz buttons: Reset
I am not able to replicate this behaviour, so I used the following configuration:
- Press the 2.4GHz button: RFKILL (disable/enable every wireless interfaces)
- Press the 5GHz button: Reset
Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
This adds support for the Ubiquiti Picostation M (XM), which has the
same board/LEDs as the Bullet M XM, but different case and antennas.
Specifications:
- AR7241 SoC @ 400 MHz
- 32 MB RAM
- 8 MB SPI flash
- 1x 10/100 Mbps Ethernet, 24 Vdc PoE-in
- External antenna: 5 dBi (USA), 2 dBi (EU)
- POWER/LAN green LEDs
- 4x RSSI LEDs (red, orange, green, green)
- UART (115200 8N1) on PCB
Flashing via WebUI:
Upload the factory image via the stock firmware web UI.
Attention: airOS firmware versions >= 5.6 have a new bootloader with
an incompatible partition table!
Please downgrade to <= 5.5 _before_ flashing OpenWrt!
Refer to the device's Wiki page for further information.
Flashing via TFTP:
Same procedure as other NanoStation M boards.
- Use a pointy tool (e.g., pen cap, paper clip) and keep the reset
button on the device or on the PoE supply pressed
- Power on the device via PoE (keep reset button pressed)
- Keep pressing until LEDs flash alternatively LED1+LED3 =>
LED2+LED4 => LED1+LED3, etc.
- Release reset button
- The device starts a TFTP server at 192.168.1.20
- Set a static IP on the computer (e.g., 192.168.1.21/24)
- Upload via tftp the factory image:
$ tftp 192.168.1.20
tftp> bin
tftp> trace
tftp> put openwrt-ath79-generic-xxxxx-ubnt_picostation-m-squashfs-factory.bin
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This adds support for the Ubiquiti Nanostation Loco M (XM), which
has the same board/LEDs as the Bullet M XM, but different case and
antennas.
Specifications:
- AR7241 SoC @ 400 MHz
- 32 MB RAM
- 8 MB SPI flash
- 1x 10/100 Mbps Ethernet, 24 Vdc PoE-in
- NS Loco M2: built-in antenna: 8 dBi; AR9287
- NS Loco M5: built-in antenna: 13 dBi; 2T2R 5 GHz radio
- POWER/LAN green LEDs
- 4x RSSI LEDs (red, orange, green, green)
- UART (115200 8N1) on PCB
Flashing via WebUI:
Upload the factory image via the stock firmware web UI.
Note that only certain firmware versions accept unsigned
images. Refer to the device's Wiki page for further information.
Flashing via TFTP:
Same procedure as other NanoStation M boards.
- Use a pointy tool (e.g., pen cap, paper clip) and keep the reset
button on the device or on the PoE supply pressed
- Power on the device via PoE (keep reset button pressed)
- Keep pressing until LEDs flash alternatively LED1+LED3 =>
LED2+LED4 => LED1+LED3, etc.
- Release reset button
- The device starts a TFTP server at 192.168.1.20
- Set a static IP on the computer (e.g., 192.168.1.21/24)
- Upload via tftp the factory image:
$ tftp 192.168.1.20
tftp> bin
tftp> trace
tftp> put openwrt-ath79-generic-xxxxx-ubnt_nanostation-loco-m-squashfs-factory.bin
Tested on NanoStation Loco M2.
Signed-off-by: Sven Roederer <freifunk@it-solutions.geroedel.de>
Co-developed-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adapt Netgear WNDR3700v2 device identification string to ath79 naming
scheme by changing from 'wndr3700v2' to 'wndr3700-v2' (affects config,
makefile, init scripts and device tree definition).
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
This commit adds support for the MikroTik RouterBOARD wAP G-5HacT2HnD
(wAP AC), a small weatherproof dual band, dual-radio 802.11ac
wireless AP with integrated omnidirectional anntennae and one
10/100/1000 Mbps Ethernet port.
See https://mikrotik.com/product/RBwAPG-5HacT2HnD for more info.
Specifications:
- SoC: Qualcomm Atheros QCA9556
- RAM: 64 MB
- Storage: 16 MB NOR
- Wireless:
· Atheros AR9550 (SoC) 802.11b/g/n 2x2:2, 2 dBi antennae
· Qualcomm QCA9880 802.11a/n/ac 3x3:3, 2 dBi antennae
- Ethernet: Atheros AG71xx (SoC, AR8033), 1x 1000/100/10 port,
passive PoE in
Working:
- Board/system detection
- Sysupgrade
- Serial console
- Ethernet
- 2.4 GHz radio
- 5 GHz radio and LED
- Reset button
Not working/Unsupported:
- 2.4 GHz LED
- AP/CAP LED
- ZT2046Q SPI temperature and voltage sensor
This adds the basic features for supporting MikroTik devices:
- a common recipe for mikrotik images in common-mikrotik.mk
- support for minor (MikroTik NOR) split firmware (only for
generic subtarget so far)
Acknowledgments: Robert Marko <robimarko@gmail.com>
Andrew Cameron <apcameron@softhome.net>
Koen Vandeputte <koen.vandeputte@ncentric.com>
Chuanhong Guo <gch981213@gmail.com>
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Co-developed-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
This commit adds support for the D-Link DIR-505, previously supported in
ar71xx.
Hardware
--------
SoC: Atheros AR9330
FLASH: 8M SPI-NOR
RAM: 64M
WIFI: 1T1R 1SS Atheros AR9330
LED: Power green, Status red
BTN: WPS, Reset
Installation
------------
Currently, installation is only possible by sysupgrading from an earlier
OpenWrt version, U-Boot TFTP or a modded U-Boot. I do not have the
original bootloader from D-Link on my device anymore, so i cannot test
the factory image.
Signed-off-by: David Bauer <mail@david-bauer.net>
The TL-WDR4300 v1 sold in Israel has a different TPLINK_HWID.
Thanks to Josh4300 for testing on device.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
When Nanostation M was renamed from ubnt,nano-m to ubnt,nanostation-m
in commit f1396ac753 ("ath79: align naming of Ubiquiti Nanostation M"),
the caldata extraction in 10-ath9k-eeprom was overlooked.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This patch adds ath79 support for Netgear WNR2200.
Router was previously supported by ar71xx target only (8 MiB variant).
Netgear WNR2200 has two flash versions - 8MiB sold in EU, US etc. and
16 MiB for Russia and China markets. Apart from flash size both variants
share the same hardware specification.
Specification
=============
* Description: Netgear WNR2200
* Loader: U-boot
* SOC: Atheros AR7241 (360 MHz)
* RAM: 64 MiB
* Flash: 8 MiB or 16 MiB (SPI NOR)
- U-boot binary: 256 KiB
- U-boot environment: 64 KiB
- Firmware: 7808 KiB or 16000 KiB
- ART: 64 KiB
* Ethernet: 4 x 10/100 LAN + 1 x 10/100 WAN
* Wireless: 2.4 GHz b/g/n (Atheros AR9287)
* USB: yes, 1 x USB 2.0
* Buttons:
- Reset
- WiFi (rfkill)
- WPS
* LEDs:
- Power (amber/green)
- WAN (amber/green)
- WLAN (blue)
- 4 x LAN (amber/green)
- WPS (green)
* UART: 4-pin connector JP1, 3.3V (Vcc, TX, RX, GND), 115200 8N1
* Power supply: DC 12V 1.5A
* MAC addresses: LAN on case label, WAN +1, WLAN +2
Installation
============
* TFTP recovery
* TFTP via U-boot prompt
* sysupgrade
* Web interface
Test build configuration
========================
CONFIG_TARGET_ath79=y
CONFIG_TARGET_ath79_generic=y
CONFIG_TARGET_ath79_generic_DEVICE_netgear_wnr2200-8m=y
CONFIG_ALL_KMODS=y
CONFIG_DEVEL=y
CONFIG_CCACHE=y
CONFIG_COLLECT_KERNEL_DEBUG=y
CONFIG_IMAGEOPT=y
CONFIG_KERNEL_DEBUG_INFO=y
CONFIG_KERNEL_DEBUG_KERNEL=y
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
Due to rebase of the base-files split patch after adding support
for the ZyXEL NBG6716, its base-files were added to the generic
subtarget, although the device belongs to the nand subtarget.
This moves the definitions to their proper locations.
Fixes: 0130022bae ("ath79: split base-files into subtargets")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
[improve commit message, rebase]
Signed-off-by: David Bauer <mail@david-bauer.net>
While most of the target's contents are split into subtargets, the
base-files are maintained for the target as a whole.
However, OpenWrt already implements a mechanism that will use (and
even prefer) files in the subtargets' directories. This can be
exploited to make several scripts subtarget-specific and thus save
some space (especially helpful for the tiny devices).
The only script remaining in parent base-files is
/etc/hotplug.d/ieee80211/00-wifi-migration, everything else is
moved/split.
Note that this will increase overall code lines, but reduce code
per subtarget.
base-files ipk size reduction:
master (generic) 49135 B
split (generic) 48533 B (- 0.6 kiB)
split (tiny) 43337 B (- 5.7 kiB)
split (nand) 44423 B (- 4.6 kiB)
Tested on TL-WR1043ND v4 (generic) and TL-WR841N v12 (tiny).
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Roger Pueyo Centelles
Davide Fioravanti
Adrian Schmutzler
Sven Roederer
Michal Cieslakiewicz
David Bauer