This ports support for the TL-WA830RE v1 range extender from ar71xx to
ath79.
Specifications:
- SOC: Atheros AR7240
- CPU: 400MHz
- Flash: 4 MiB (Spansion S25FL032P)
- RAM: 32 MiB (Zentel A3S56D40FTP-G5)
- WLAN: Atheros AR9280 bgn 2x2
- Ethernet: 1 port (100M)
Flash instructions:
- install from u-boot with tftp (requires serial access)
> setenv ipaddr a.b.c.d
> setenv serverip e.f.g.h
> tftpboot 0x80000000 \
openwrt-ath79-tiny-tplink_tl-wa830re-v1-squashfs-factory.bin
> erase 0x9f020000 +0x3c0000
> cp.b 0x80000000 0x9f020000 0x3c0000
> bootm 0x9f020000
- flash factory image from OEM WebUI
- sysupgrade from ar71xx image
The device seems to be a clone of the following devices not yet
added to ath79:
- tl-wa701nd-v1
- tl-wa730re-v1
- tl-wa801nd-v1
- tl-wa901nd-v1
Signed-off-by: Christian Buschau <christian.buschau@mailbox.org>
[make use of ar7240_tplink.dtsi, add note about clones]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The current set of TP-Link devices with ar7240 SoC all share
the same DTSI file. As the latter is very similar to the
definition required for the to-be-supported TP-Link TL-WA devices
with ar7240, this patch splits the definitions into a shared part
for all TP-Link devices (ar7240_tplink.dtsi) and a file containing
the specific setup for the present TL-WR devices
(ar7240_tplink_tl-wr.dtsi), equivalent to the former
ar7240_tplink_tl-wr74xn-v1.dtsi.
While at it, remove unused firmware partition label and rename
pinmux_switch_led_pins.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
If bootloader doesn't terminate its last spi operation properly
before starting kernel, our first transfer in kernel becomes a
continuous transfer to that request instead of a new one.
Fix this flaw by restoring IOC register, which restored all pin
state to default.
Fixes: ebf0d8dade ("ath79: add new ar934x spi driver")
Reported-by: Russell Senior <russell@personaltelco.net>
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* wg-quick: android: split uids into multiple commands
Newer android's ndc implementations have limits on uid size, so we have to
break these into several lists.
* man: document dynamic debug trick for Linux
This comes up occasionally, so it may be useful to mention its
possibility in the man page. At least the Arch Linux and Ubuntu kernels
support dynamic debugging, so this advice will at least help somebody. So that
you don't have to go digging into the commit, this adds this helpful tidbit
to the man page for getting debug logs on Linux:
# modprobe wireguard && echo module wireguard +p > /sys/kernel/debug/dynamic_debug/control
* extract-{handshakes,keys}: rework for upstream kernel
These tools will now use the source code from the running kernel instead of
from the old monolithic repo. Essential for the functioning of Wireshark.
* netlink: remove libmnl requirement
We no longer require libmnl. It turns out that inlining the small subset of
libmnl that we actually use results in a smaller binary than the overhead of
linking to the external library. And we intend to gradually morph this code
into something domain specific as a libwg emerges. Performance has also
increased, thanks to the inliner. On all platforms, wg(8) only needs a normal
libc. Compile time on my system is still less than one second. So all in all
we have: smaller binary, zero dependencies, faster performance.
Packagers should no longer have their wireguard-tools package depend on
libmnl.
* embeddable-wg-library: use newer string_list
* netlink: don't pretend that sysconf isn't a function
Small cleanups.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
When changing compatibles in e4ba8c8294 ("brcm63xx: use more systematic
names for image and DTS files"), I forgot to update them in kernel
patches as well. So, do it now.
Fixes: e4ba8c8294 ("brcm63xx: use more systematic names for image and DTS files")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This uses the specific SOC names for several devices where the
Chip ID was used incorrectly before.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Since the model string in DTS is not required to derive board name
anymore, we can now align it with the model name in Makefile and
the compatible.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This patch removes the translation of device model name into a
board name in lib/brcm63xx.sh. The latter has been actually totally
useless as we have the compatible which can be used instead of
the board name (and actually is at other targets like ath79 or ramips).
The change requires updating the base-files with the new
identifiers based on compatible.
With all "board names" replaced by the compatible, we do not need
the old scripts to detect board name anymore and can also remove
the obsolete treatment of "legacy" devices without DTS, as there
are none of those left. So, this patch removes the target-specific
board detection and uses the standard procedure in
package/base-files/files/lib/preinit/02_sysinfo
This also fixes several cases where the board name was not set or
evaluated correctly:
- asmax,ar1004g in 02_network
- telsey,magic in 09_fix_crc/02_network
- brcm,bcm96338gw in 02_network
- brcm,bcm96338w in 02_network
- brcm,bcm96348gw in 02_network
- dynalink,rta1025w in 02_network
- huawei,echolife-hg520v in 02_network
- several cases in diag.sh
The following orphaned identifiers are removed from board.d files:
- dmv-s0
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
In brcm63xx image Makefile DEVICE_PACKAGE definitions are split
into multiple lines with no apparent need.
Merge them into one line to increase readability and maintainability.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This changes brcm63xx target to achieve consistency between image
names, device nodes names, compatible, DTS name and device name
as much as possible. As with other targets, having consistent
names is supposed to make life easier for developers and reduces
the number of "variables" in the system. In particular, applying
the DTS scheme will make it easier to find the correct file and
architecture.
DTS files are named based on the increasingly common
soc-vendor-model scheme, using hyphens for separation as this seems
to be the kernel way. Since the compatible is not used at the
moment, I took the chance to also align them with this patch.
For the SOC, the already existing CFE_CHIP_ID can be exploiting
for all but two devices.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Most of the broadcom packaging codes were moved to broadcom.mk in commit
7f984dab1c ("mac80211: move broadcom packaging code to broadcom.mk"),
but b43/install still remained. Move it now.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
The $(space) definition in the hostapd Makefile ceased to work with
GNU Make 4.3 and later, leading to syntax errors in the generated
Kconfig files.
Drop the superfluous redefinition and reuse the working $(space)
declaration from rules.mk to fix this issue.
Fixes: GH#2713
Ref: https://github.com/openwrt/openwrt/pull/2713#issuecomment-583722469
Reported-by: Karel Kočí <cynerd@email.cz>
Suggested-by: Jonas Gorski <jonas.gorski@gmail.com>
Tested-by: Shaleen Jain <shaleen@jain.sh>
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The correct model name of WF-2881 is WF2881 without hyphen. The former used
boardnames are not added to SUPPORTED_DEVICES, to make it explicit that the
sysupgrade-tar image, which is newly added in the previous commit, should
not be used to upgrade from older version.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[adjust commit title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
WF-2881 sysupgrade image uses UBI rootfs, but still relies on
default_do_upgrade. Because of this, config backup is not restored after
sysupgrade. It can be fixed by switching to nand_do_upgrade and
sysupgrade-tar image. default_do_upgrade does not handle sysupgrade-tar
properly, so one should use factory image to upgrade from older version.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Inspired by commit c48b571ad7, add an LED trigger for the WAN LED on top of
the TP-Link TL-WR902AC v1. Currently, only the LED on the port itself shows the
link state, while the LED on top of the device stays dark.
The WAN port of the device is a hybrid LAN/WAN one, hence why the LED at the
port was labeled LAN.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
AR934x chips also got the 'old' qca,ar9330-uart in addition to the
'new' ns16550a compatible one. Add support for UART1 clock selector as
well as device-tree bindings in ar934x.dtsi to make use of that uart.
Reported-by: Piotr Dymacz <pepe2k@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
On AR934x this UART is usually not initialized by the bootloader
as it is only used as a secondary serial port while the primary
UART is a newly introduced NS16550-compatible.
In order to make use of the ar933x-uart on AR934x without RTS/CTS
hardware flow control, one needs to set the
UART_CS_{RX,TX}_READY_ORIDE bits as other than on AR933x where this
UART is used as primary/console, the bootloader on AR934x typically
doesn't set those bits.
Setting them explicitely on AR933x does not do any harm, so just set
them unconditionally.
Tested-by: Chuanhong Guo <gch981213@gmail.com
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Luxul ABR-4500 and XBR-4500 devices are wired routers with 5 Ethernet
ports and 1 USB 3.0 port. Flashing requires using Luxul firmware 6.4.0
or newer and uploading firmware using "Firmware Update" web UI page.
Signed-off-by: Dan Haab <dan.haab@legrand.com>
This new function make batch processing of network packets possible,
which slightly improves performance.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Tested-by: Rosen Penev <rosenp@gmail.com>
XTX XT25F128A shares it's chip ID with XM25QH128A which got identical
features. Hence there it makes no sense to add it to the driver.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
ar933x appears to have the same spi controller as ar934x but it's
not mentioned in datasheet at all. Use new spi driver instead to
gain more flash operating performance.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
A new shift mode was introduced since ar934x which has a way better
performance than current bitbang driver and can handle higher spi
clock properly. This commit adds a new driver to make use of this
new feature.
This new driver has chipselect properly configured and we don't need
cs-gpios hack in dts anymore. Remove them.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* compat: support building for RHEL-8.2
* compat: remove RHEL-7.6 workaround
Bleeding edge RHEL users should be content now (which includes the actual
RedHat employees I've been talking to about getting this into the RHEL kernel
itself). Also, we remove old hacks for versions we no longer support anyway.
* allowedips: remove previously added list item when OOM fail
* noise: reject peers with low order public keys
With this now being upstream, we benefit from increased fuzzing coverage of
the code, uncovering these two bugs.
* netns: ensure non-addition of peers with failed precomputation
* netns: tie socket waiting to target pid
An added test to our test suite for the above and a small fix for high-load CI
scenarios.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
This commit adds the ability to set custom uImage magic to
Build/wr1201-factory-header and renames it to
"Build/custom-initramfs-uimage".
Custom uImage header in initramfs image is required on following
devices:
- I-O DATA WN-AX1167GR2
- I-O DATA WN-AX2033GR
- I-O DATA WN-AX2033GR2
- I-O DATA WN-DX1167R
While at it, fix typo in comment.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Reviewed-by: Sungbo Eo <mans0n@gorani.run>
[shorten commit title, minor commit message adjustments]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This reverts commit 96424c143d.
The commit changed libiwinfo's internal ABI which breaks a number of
downstream projects, including LuCI and rpcd-mod-iwinfo.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Bump procd package to reduce log spam related to missing jail binaries
in a non-jail capable system.
bcb8655 instance: add 'requirejail' attribute
An additional jail attribute 'requirejail' can now be used to indicate
mandatory use of a jailed environment and hence prevent process startup
in the event that the jail subsystem is unavailable.
Procd will now only log errors if jail is unavailable and 1) is a mandatory
requirement or 2) a procd debug level of at least 2 is in use.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
eba5a20 iwinfo: add device id for BCM43602
a6914dc iwinfo: add BSS load element to scan result
bb21698 iwinfo: add device id for Atheros AR9287
7483398 iwinfo: add device id for MediaTek MT7615E
Signed-off-by: David Bauer <mail@david-bauer.net>
dts file does not need to be executable. 644 is enough.
Fixes: f098c612b6 ("ramips: create shared DTSI for Netgear EX2700 and WN3000RP v3")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
kernel config and patch files do not need to be executable. 644 is enough.
Fixes: 01c8f2e97c ("mediatek: bump to v4.19")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Add Netgear WNDR3700v2 to the list of supported boards.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
[rebase, adjusted commit title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Remove read-only flag from U-boot environment partition for Netgear
WNDR3700 v1 and v2 so u-boot-envtools can modify data there.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
Since whole target has been bumped to kernel 4.19 in 01c8f2e97c
("mediatek: bump to v4.19") we do not need the overwrite in mt7629
subtarget anymore.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This commit adds support for the COMFAST CF-E560AC, an ap143 based
in-wall access point.
Specifications:
- SoC: Qualcomm Atheros QCA9531
- RAM: 128 MB DDR2 (Winbond W971GG6SB-25)
- Storage: 16 MB NOR (Winbond 25Q128JVSO)
- WAN: 1x 10/100 PoE ethernet (48v)
- LAN: 4x 10/100 ethernet
- WLAN1: QCA9531 - 802.11b/g/n - 2x SKY85303-21 FEM
- WLAN2: QCA9886 - 802.11ac/n/a - 2x SKY85735-11 FEM
- USB: one external USB2.0 port
- UART: 3.3v, 2.54mm headers already populated on board
- LED: 7x external
- Button: 1x external
- Boot: U-Boot 1.1.4 (pepe2k/u-boot_mod)
MAC addressing:
- stock
LAN *:40 (label)
WAN *:41
5G *:42
2.4G *:4a
- flash (art partition)
0x0 *:40 (label)
0x6 *:42
0x1002 *:41
0x5006 *:43
This device contains valid MAC addresses in art 0x0, 0x6, 0x1002 and
0x5006, however the vendor firmware only reads from art:0x0 for the LAN
interface and then increments in 02_network. They also jump 8 addresses
for the second wifi interface (2.4 GHz). This behavior has been duplicated
in the DTS and ath10k hotplug to align addresses with the vendor firmware
v2.6.0.
Recovery instructions:
This device contains built-in u-boot tftp recovery.
1. Configure PC with static IP 192.168.1.10/24 and tftp server.
2. Place desired image at /firmware_auto.bin at tftp root.
3. Connect device to PC, and power on.
4. Device will fetch flash from tftp, flash and reboot into new image.
Signed-off-by: August Huber <auh@google.com>
[move jtag_disable_pins, remove unnecessary statuses in DTS, remove
duplicate entry in 11-ath10k-caldata, remove hub_port0 label in DTS]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adapt Netgear WNDR3700v2 device identification string to ath79 naming
scheme by changing from 'wndr3700v2' to 'wndr3700-v2' (affects config,
makefile, init scripts and device tree definition).
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
Christian Buschau
Adrian Schmutzler
Chuanhong Guo
Hans Dedecker
Jason A. Donenfeld
Sungbo Eo
Jo-Philipp Wich
Lech Perczak
Daniel Golle
Dan Haab
Rafał Miłecki
INAGAKI Hiroshi
Kevin Darbyshire-Bryant
David Bauer
Álvaro Fernández Rojas
Koen Vandeputte
Michal Cieslakiewicz
John Crispin
August Huber
Felix Fietkau