The qca9557/qca956x reset-controller aren't a simple bus. A simple bus
would require node unit addresses.
Add the node unit addresses for the qca9557 usb phys. Add the regs for
the USB_PWRCTL and USB_CONFIG registers even not yet used.
Fix the wrong ar7100 pcie controller node unit address as well.
Signed-off-by: Mathias Kresin <dev@kresin.me>
PowerCloud Systems CAP324 has a bicolor power LED and OpenWrt DTS files /
base files support using both colours to better inform user of state
and to better match stock firmware, so use green power to indicate
normal operation.
Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
I-O DATA WN-AG300DGR is a 2T2R 2.4/5 GHz 11n router, based on Atheros
AR1022.
WN-AG300DGR does not have an LED to indicates power or system status,
I set "router" LED as OpenWrt status LED.
There is no eeprom data for 5 GHz wlan in "art" partition.
Specification:
- Atheros AR1022
- 64 MB of RAM (DDR2)
- 8 MB of Flash (SPI-NOR)
- 2T2R 2.4/5GHz wifi
- 2.4 GHz: SoC internal
- 5 GHz: Atheros AR93x2
- 5x 10/100/1000 Mbps Ethernet
- 6x LEDs, 6x keys (4x buttons, 1x slide switch)
- 1x USB 2.0 Type-A
- UART through-hole on PCB
- Vcc, GND, TX, RX from ethernet port side
- 115200n8
Flash instruction using factory image:
1. Connect the computer to the LAN port on WN-AG300DGR
2. Connect power cable to WN-AG300DGR and turn it
3. Access to "http://192.168.0.1/" and open firmware update page
("ファームウェア")
4. Select the OpenWrt factory image and click update ("更新") button
5. Wait ~150 seconds to complete flashing
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
WB2000 is a dual-band 11N AP using AR9344.
The factory firmware used the original DB120 partition table
with a small kernel partition at the end of firmware and the
kernel will easily get oversized in the future. Since it has
to be flashed using UART I also swapped kernel/rootfs and
changed the default load address.
Specification:
- SoC: Atheros AR9344
- RAM: 128 MB
- Flash: 16 MB
- Ethernet: 10/100/1000 Mbps (Atheros AR8035)
- 2x USB 2.0
- WIFI: AR9344(2G) + AR9382(5G)
- RTC: DS1338
Known issue:
5G ath9k led doesn't work due to commit ccab68f.
Flash instruction:
Set up a TFTP server on your computer and configure static IP.
Connect UART (J11 TX/GND/RX) and press any key to enter U-boot
shell.
1. Change the default boot command:
setenv bootcmd 'bootm 0x9f050000 || bootm 0x9fd50000'
saveenv
2. Set your router ipaddr and server ipaddr. e.g.:
setenv ipaddr 192.168.1.1
setenv serverip 192.168.1.50
3. Load and flash the firmware:
tftp 0x80060000 fw.bin
erase 0x9f050000 +$filesize
cp.b $fileaddr 0x9f050000 $filesize
4. Reset your router:
reset
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
[Drop the i2c node unit address. Move the ath9k-leds node out of the spi
node, it doesn't belong there. Add the #gpio-cells property to the pci
wifi node. All fix dtc compiler warnings]
Signed-off-by: Mathias Kresin <dev@kresin.me>
merge
This commit fixes several issues in eth0 on ETG3-R, and solve slowdown
in NA(P)T speed.
- add gmac-config with correct configurations
- fix pll-data value
And I added ref clock-frequency.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Neither the seama nor the wrgg splitter are used at the moment. Drop
them for now to not bloat the target from the beginning.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The userspace boardname derived from the dts compatible was out of sync
with the expected board added to the image metadata. This way a
sysupgrade is refused.
Sync the userspace boardname and the baordname used in the image metdata
to allow a seamless sasupgrade.
Signed-off-by: Mathias Kresin <dev@kresin.me>
This commit adds firmware partition compatible for the
AVM FRITZ!Box 4020 and AVM FRITZ!WLAN Repeater 300E.
This allows to select the correct mtdsplit parser
instead of trying all available ones one by one.
Signed-off-by: David Bauer <mail@david-bauer.net>
Parsing "firmware" partition (to create kernel + rootfs) was implemented
using OpenWrt downstream code enabled by CONFIG_MTD_SPLIT_FIRMWARE. With
recent upstream mtd changes we can do it in a more clean way for DTS
targets. It just requires adding a proper "compatible" string to the
"firmware" partition node.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
qca9533 is a costdown version of qca9531 which doesn't have USB and PCIE.
Rename the misleading dtsi names and fix the SoC type of gl-ar300m.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
[apply the changes for the gl-x750 as well]
Signed-off-by: Mathias Kresin <dev@kresin.me>
I wanted to add status LEDs support to my imx6 based board and have found out,
that I could use diag.sh script found in ramips platform, which seems to be
also shared in a few other platforms:
4801276bc2078c5bcf03003c831e3b0a target/linux/ramips/base-files/etc/diag.sh
4801276bc2078c5bcf03003c831e3b0a target/linux/ipq40xx/base-files/etc/diag.sh
4801276bc2078c5bcf03003c831e3b0a target/linux/ath79/base-files/etc/diag.sh
And @chunkeey suggested to me, that I can also add lantiq, ipq806x and
apm821xx to the list of platforms which could share this generic
diag.sh.
I've extended the base diag.sh in a way, that if it detects any of the
DTS LED aliases, then it would use the generic DTS set_led_state code.
The code in platform's diag.sh has moved to base-files package in this
commit:
base-files: diag.sh: Make it more generic towards DTS so it could be reused
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Tested-by: Christian Lamparter <chunkeey@gmail.com> (apm821xx and ipq40xx)
Indoor low-power router with 2.4 GHz radio
CPU: Atheros AR7241 rev 1
RAM: 32 MB
Flash: 8 MB NOR SPI
Switch: Atheros AR7240
Ports: 1x WAN, 4x LAN 10/100 Ethernet
WLAN: Atheros AR9285 (2.4 GHz)
USB: 1x USB2 host port
Note: Ethernet WAN/LAN port naming is reversed from ar71xx.
WAN is eth0; LAN is eth1.1.
UART settings: 115200, 8N1
LEDs
+--------------------------
|
|
|
|
|
|
|
|
VCC | x x
RX | * x
| x x
| x x
TX | * x
GND | * x
|
|
|
|
+--------------------------
ETHERNET PORTS
Installation from Ubiquiti firmware, is as for other ubnt-xm AirOs devices.
Signed-off-by: Russell Senior <russell@personaltelco.net>
Having MIT as alternative is sometimes preferred by upstream maintainers
and allows sharing that simple code with other projects. We don't really
want multiple DTS versions for the same device.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Having MIT as alternative is sometimes preferred by upstream maintainers
and allows sharing that simple code with other projects. We don't really
want multiple DTS versions for the same device.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This commit adds support for the ROSINSON WR818 WiFi-Router
SoC: Qualcomm Atheros QCA9563,
FLASH: Winbond W25Q128FV 16MBytes,
WiFi: QCA9563 b/g/n 3x3 450Mbit/s,
USB: 1x USB 2.0 Type A, 1x USB2.0 Type C,
IN: WPS/Reset button GPIO1,
OUT: Power LED red, Internet LED red, WLAN LED red,
LAN1 LED red, LAN2 LED red, System LED red,
UART: RX-GPIO18, TX-GPIO22,
Tested and working:
- Ethernet (LAN + WAN)
- WiFi
- OpenWRT sysupgrade
- Button
- LEDs
Installation of OpenWRT from vendor firmware:
- Connect to the Web-interface at http://192.168.1.1
- Go to "Administration" -> "Firmware Upgrade"
- Upload the OpenWrt sysupgrade image
Signed-off-by: Rosy Song <rosysong@rosinson.com>
The board doesn't come in different flash type flavours, hence there is
no need to keep a dtsi + dts for this purpose.
While at it, fix some whitespace issues.
Signed-off-by: Mathias Kresin <dev@kresin.me>
This commit adds firmware partition compatible for the
TP-Link Archer C58 v1 and Archer C59 v1.
Since a22311e this allows to select the correct mtdsplit
parser instead of trying all available ones one by one.
Signed-off-by: David Bauer <mail@david-bauer.net>
This commit adds firmware partition compatible for the
OCEDO Raccoon and OCEDO Koala.
Since a22311e this allows to select the correct mtdsplit
parser instead of trying all available ones one by one.
Signed-off-by: David Bauer <mail@david-bauer.net>
Specify firmware partition format (denx,uimage) by compatible string
for ELECOM WRC-300GHBK2-I.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
This commit modifies mtd partitions define for Buffalo BHR-4GRV2 and
move it to generic subtarget.
In Buffalo BHR-4GRV2, "kernel" partition is located behined "rootfs"
partition in the stock firmware. This causes the size of the kernel
to be limited by the fixed value.
0x50000 0xe80000 0xff0000
+-------------------------------+--------------+
| rootfs | kernel |
| (14528k) | (1472k) |
+-------------------------------+--------------+
After ar71xx was updated to Kernel 4.14, the kernel size of BHR-4GRV2
exceeded the limit, and it breaks builds on official buildbot.
Since this issue was also confirmed in ath79, I modified the mtd
partitions to get rid of that limitation.
0x50000 0xff0000
+----------------------------------------------+
| firmware |
| (16000k) |
+----------------------------------------------+
However, this commit breaks compatibility with ar71xx firmware, so I
dropped "SUPPORTED_DEVICES += bhr-4grv2".
This commit requires new flash instruction instead of the old one.
Flash instruction using initramfs image:
1. Connect the computer to the LAN port of BHR-4GRV2
2. Set the IP address of the computer to 192.168.12.10
3. Rename the OpenWrt initramfs image to
"bhr4grv2-uImage-initramfs-gzip.bin" and place it into the TFTP
directory
4. Start the tftp server on the computer
5. While holding down the "ECO" button, connect power cable to
BHR-4GRV2 and turn on it
6. Flashing (orange) diag LED and release the finger from the button,
BHR-4GRV2 downloads the intiramfs image from TFTP server and boot
with it
7. On the initramfs image, create "/etc/fw_env.config" file with
following contents
/dev/mtd1 0x0 0x10000 0x10000
8. Execute following commands to add environment variables for
u-boot
fw_setenv ipaddr 192.168.12.1
fw_setenv serverip 192.168.12.10
fw_setenv ethaddr 00:aa:bb:cc:dd:ee
fw_setenv bootcmd "bootm 0x9f050000 || bootm 0x9fe80000"
9. Perform sysupgrade with squashfs-sysupgrade image
10. Wait ~150 seconds to complete flashing
And this commit includes small fix; BHR-4GRV2 has QCA9557 as a SoC,
not QCA9558.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Remove the source-only flag from ath79, its supposed to replace ar71xx after next stable release but buildbots are not currently generating images for it.
So in order to expand testing as much as possible and prepare for moving to ath79 lets enable the buildbots to actually build the target.
Signed-off-by: Robert Marko <robimarko@gmail.com>
This commit adds support for the Archer C58 v1 and C59 v1, previously
supported in the ar71xx target.
CPU: Qualcomm QCA9561
RAM: 64M (C58) / 128M (C59)
FLASH: 8M (C58) / 16M (C59)
WiFi: QCA9561 bgn 3x3:3
QCA9888 nac 2x2:2
LED: Power, WiFi 2.4, WiFi 5, WAN green, WAN amber, LAN, WPS
Only C59: USB
BTN: WPS, WiFi, Reset
Installation
------------
Via Web-UI:
Update factory image via Web-UI.
Via TFTP:
Rename factory image to "tp_recovery.bin" and place it in the root-dir
of your tftp server. Configure to listen on 192.168.0.66. Power up the
router while holding down the reset-button. The router will flash itself
and reboot.
Note: For TFTP, you might need a switch between router and computer, as
link establishment might take to long.
Signed-off-by: David Bauer <mail@david-bauer.net>
this patch adds supports for GL-X750.
Specification:
- SOC: QCA9531 (650MHz)
- Flash: 16 MiB (W25Q128FVSG)
- RAM: 128 MiB DDR2
- Ethernet: 10/100: 1xLAN + 10/100: 1xWAN
- Wireless: 2.4GHz (bgn) and 5GHz (ac)
- USB: 1x USB 2.0 port
- Button: 1x reset button
- LED: 5x LEDS (green)
Flash instruction:
The original firmware is openwrt, so both LuCI or sysupgrade can be used.
Signed-off-by: Luo chongjun <luochongjun@gl-inet.com>
Ubiquity allows flashing of unsigned factory images via TFTP recovery
method[1]. They claim in airOS v6.0.7 release changelog[2] following:
All future airOS versions will be signed in this way and not allow
unsigned firmware to be loaded except via TFTP.
U-boot bootloader on M-XW devices expects factory image revision
version in specific format. On airOS v6.1.7 with `U-Boot 1.1.4-s1039
(May 24 2017 - 15:58:18)` bootloader checks if the revision major(?)
number is actually a number, but in currently generated images there's
OpenWrt text and so the check fails:
Hit any key to stop autoboot: 0
Setting default IP 192.168.1.20
Starting TFTP server...
Receiving file from 192.168.1.25:38438
Received 4981148 bytes
Firmware check failed! (1)
By placing arbitrary correct number first in major version, we make the
bootloader happy and we can flash factory images over TFTP again:
Received 3735964 bytes
Firmware Version: XW.ar934x.v6.0.4-42.r8474-56aa1ac-OpenWrt
Setting U-Boot environment variables
Un-Protected 1 sectors
Erasing Flash.... done
Patch provided by AREDN[3] project, tested on Bullet M2 XW (ynezz) and
Nanostation M5 XW (ae6xe).
1. https://help.ubnt.com/hc/en-us/articles/204910124-UniFi-TFTP-Recovery-for-Bricked-Access-Points
2. https://dl.ubnt.com/firmwares/XW-fw/v6.0.7/changelog.txt
3. https://github.com/aredn
Signed-off-by: Petr Štetiar <ynezz@true.cz>
CPU: AR9342 SoC
RAM: 64 MB DDR2
Flash: 8 MB NOR SPI
Ports: 100 MBit (24V PoE in)
WLAN: 2.4/5 GHz
UART: 1 UART on PCB marked as J1 with 115200 8N1 config
LEDs: Power, Ethernet, 4x RSSI LEDs (orange, red, 2x green)
Buttons: Reset
UART connection details
.---------------------------------.
| |
[ETH] J1 [ANT]
| o VCC o RX o TX o GND |
`---------------------------------'
Flashing instructions
A) Serial console, U-Boot and TFTP
1. Connect to serial header J1 on the PCB
2. Power on device and enter U-Boot console
3. Set up TFTP server serving an OpenWrt initramfs build
4. Load initramfs build using the command tftpboot in the U-Boot cli
5. Boot the loaded image using the command bootm
6. Copy squashfs OpenWrt sysupgrade build to the booted device
7. Use mtd to write sysupgrade to partition "firmware"
8. Reboot and enjoy
B) Experimental factory image flashing over SSH from airOS v6.1.7
1. You need to flash your UBNT M2HP with airOS v6.1.7 firmware
no other airOS version is currently supported
2. git clone https://github.com/true-systems/ubnt-bullet-m2hp-openwrt-flashing
3. cd ubnt-bullet-m2hp-openwrt-flashing
4. make flash-factory FW_OWRT=/path/to/your/openwrt-ath79-generic-ubnt_bullet-m-xw-squashfs-factory.bin
Tested only on Bullet M2HP.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Specify the new "firmware" partition format for Netgear WNDR3700
and WNDR3700v2 similarly as ffd082aa did for WNDR3800, the third
device in the family.
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
This commit adds support for the Ubiquiti LiteAP ac (LAP-120), an outdoor
5 GHz AC access point with an integrated 120° 16 dBi antenna. The device
was previously known as LiteBeam AP ac but was later rebranded.
CPU: Atheros AR9342 SoC
RAM: 64 MB DDR2
Flash: 16 MB NOR SPI
Ports: 1 GbE port (PoE in)
WLAN: 5 GHz QCA899X (PCI)
The integrated QCA899X is a Ubiquiti branded part with modified vendor
and product id (0777:11ac9). It is very similar to the NanoStation loco
AC, except for the 2.4 GHz management radio (missing here).
Installation procedure is the same as the NanoStation [loco] AC:
1. Connect to serial header on device
2. Power on device and enter uboot console
3. Set up tftp server serving an openwrt initramfs build
4. Load initramfs build using the command tftpboot in the uboot cli
5. Boot the loaded image using the command bootm
6. Copy squashfs openwrt sysupgrade build to the booted device
7. Use mtd to write sysupgrade to partition "firmware"
8. Reboot and enjoy
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
In commit fec8fe8069 ("kernel: bump 4.9 to 4.9.116") [1], the following patch for removed:
- 403-mtd_fix_cfi_cmdset_0002_status_check.patch
This patch contained fixes for both write and erase functions.
While the chip-detects for erase got fixed upstream [2],
some modifications are still required, even with the fixes applied.
While at it, also apply the same fix for target ath79,
which suffers the same issue.
Not doing so results in following errors seen:
Collected errors:
* pkg_write_filelist: Failed to open //usr/lib/opkg/info/luci-lib-ip.list: I/O error.
* opkg_install_pkg: Failed to extract data files for luci-lib-ip. Package debris may remain!
* opkg_install_cmd: Cannot install package luci-ssl.
* opkg_conf_write_status_files: Can't open status file //usr/lib/opkg/status: I/O error.
[ 0.780920] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 8.406396] jffs2: notice: (415) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[ 8.423476] mount_root: switching to jffs2 overlay
[ 270.902671] jffs2: Write of 1989 bytes at 0x005ce6f8 failed. returned -5, retlen 962
[ 270.931965] jffs2: Write of 1989 bytes at 0x005ceec0 failed. returned -5, retlen 0
[ 270.939631] jffs2: Not marking the space at 0x005ceec0 as dirty because the flash driver returned retlen zero
[ 270.950397] jffs2: Write of 68 bytes at 0x005ceec0 failed. returned -5, retlen 0
[ 270.957838] jffs2: Not marking the space at 0x005ceec0 as dirty because the flash driver returned retlen zero
[ 270.968584] jffs2: Write of 68 bytes at 0x005ceec0 failed. returned -5, retlen 0
[ 270.976027] jffs2: Not marking the space at 0x005ceec0 as dirty because the flash driver returned retlen zero
[ 270.986735] jffs2: Write of 68 bytes at 0x005ceec0 failed. returned -5, retlen 0
[ 270.994225] jffs2: Not marking the space at 0x005ceec0 as dirty because the flash driver returned retlen zero
[1] https://git.openwrt.org/?p=openwrt/openwrt.git;a=commit;h=fec8fe806963c96a6506c2aebc3572d3a11f285f
[2] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v4.9.133&id=a0239d83e1cb60de5e78452d4708c083b9e3dcbe
Fixes: fec8fe8069 ("kernel: bump 4.9 to 4.9.116")
Signed-off-by: Fabio Bettoni <fbettoni@gmail.com>
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Add out of the box support for 802.11r and 802.11w to all targets not
suffering from small flash.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Mathias did all the heavy lifting on this, but I'm the one who should
get shouted at for committing.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
This commit adds support for the TP-Link TL-WR901ND v2 access point.
CPU: Atheros AR9132 400MHz
RAM: 32MB
FLASH: 4MiB
WiFi: Atheros AR9103 3x3:2 bgn
LED: Power (static on)
LAN (controlled by PHY)
SYS, WiFi, QSS toggleable
BTN: Reset, QSS
Installation:
Upload the factory image via the vendor-GUI.
Signed-off-by: David Bauer <mail@david-bauer.net>
Buffalo WZR-HP-G302H is a 2T2R 2.4 GHz 11n router, based on Atheros
AR7242.
It is Japanese market model of WZR-HP-G300NH2, but there are some
diffrences. This commit is based on WZR-HP-G300NH2 in ar71xx.
And, G302H has several hardware versions and hardware is different
dependent on the versions. This commit adds support for "A1A0"
version.
Specification:
- Atheros AR7242
- 64 MB of RAM (DDR2)
- 32 MB of Flash
- 2x 16 MB SPI-NOR flash
- 2.4 GHz 2T2R wifi
- Atheros AR9283
- 5x 10/100/1000 Mbps Ethernet
- Atheros AR8316
- 7x LEDs, 5x keys
- LED: 1x gpio-leds, 6x ath9k-leds
- key: 3x buttons, 2x slide switches
- UART header on PCB
- Vcc, GND, TX, RX from ethernet port side
- 115200n8
Flash instruction using factory image:
1. Boot WZR-HP-G302H normaly and connect the computer to its LAN port
2. Access to "http://192.168.11.1/" and move to firmware update page
("ファーム更新")
3. Select the OpenWrt factory image and click update ("更新実行")
button to perform firmware update
4. Wait ~200 seconds to complete flashing
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
In order to be able to set the value of "hardware version" other than
"3", I added the "hwver" parameter.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
This PR adds support for TP-Link TL-WR842N-v2 router which is supported by ar71xx to ath79.
This is a low cost model with following specs:
CPU: Atheros AR9341 SoC
RAM: 32 MB DDR1
Flash: 8 MB NOR SPI
Switch: Internal AR9341 5 port 10/100 Mbit
Ports: 5x 10/100 Mbit(1x WAN, 4x LAN)
USB: 1x USB2.0
WLAN: 2.4 GHZ AR9341
Installation:
Simply flash the factory image through stock firmware WEB UI.
Signed-off-by: Robert Marko <robimarko@gmail.com>
The image build code for the Ubiquiti Nanostation AC series adds the
factory image as to be build image. The same is already done by an
included recipe which results into an expanded IMAGE variable of:
IMAGES = sysupgrade.bin factory.bin factory.bin
The build system doesn't like these duplicates and issues the following
warning:
Makefile:82: warning: overriding recipe for target...
Get remove the duplicate factory image to get rid of the warning.
Fixes: 5736af8024 ("ath79: Add support for Ubiquiti NanoStation AC loco")
fa3c2676ab ("ath79: Add support for Ubiquiti Nanostation AC")
Signed-off-by: Mathias Kresin <dev@kresin.me>
5 GHz AC wireless outdoor PoE CPE with internal 2.4 GHz management radio
CPU: Atheros AR9342 SoC
RAM: 64 MB DDR2
Flash: 16 MB NOR SPI
Switch: QCA8334
Ports: 2 GbE ports (1x PoE in, 1x PoE passthrough)
WLAN: 5 GHz QCA899X (PCI) and 2.4 GHZ AR9342
Successor to the old NanoStation M5 with AC wireless.
The integrated QCA899X is a Ubiquiti branded part with modified vendor and
product id (0777:11ac9).
Serial
Serial settings: 115200, 8N1
* = plated through hole
0 = nylon screw
[Top of device]
+--------------------------+
| [label] |
| 0 |
| 0 |
| [ubnt] |
| [logo] 3V3 * |
| TX * |
| RX * |
| GND * |
| |
| * |
| * |
| * |
| * |
| 0 |
| 0 |
| |
| |
Installation
1. Connect to serial header on device
2. Power on device and enter uboot console
3. Set up tftp server serving an openwrt initramfs build
4. Load initramfs build using the command tftpboot in the uboot cli
5. Boot the loaded image using the command bootm
6. Copy squashfs openwrt sysupgrade build to the booted device
7. Use mtd to write sysupgrade to partition "firmware"
8. Reboot and enjoy
Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
Mathias Kresin
Daniel F. Dickinson
INAGAKI Hiroshi
Chuanhong Guo
David Bauer
Petr Štetiar
Russell Senior
Rosy Song
Robert Marko
Luo chongjun
Rafał Miłecki
Hannu Nyman
Koen Vandeputte
YuheiOKAWA
Roger Pueyo Centelles
Fabio Bettoni
Tobias Schramm