The ASL56026 is a VDSL2 router with dual 100mbit ethernet,
also known as the ECI B-FOCuS V-2FUb/I.
CPU: Lantiq XRX268 v1.1 at 333MHz
Modem: Lantiq VRX208
RAM: 32MiB DDR2 at 167MHz
Flash: 8MiB NOR, Spansion S29GL064N90TF04
UART is at JP1:
Pin 1 TX
Pin 2 GND
Pin 3 +3.3V
Pin 4 NC
Pin 5 RX
Boot selection pins are exposed via several resistor jumpers:
boot_sel0 is at J15, on the rear of the board. Default is high.
boot_sel1 is at J3, next to the flash - it is also the flash CE# pin. Default is low.
boot_sel2 is at J12, directly below the SoC. Default is low.
boot_sel3 is at J16, on the rear of the board. Default is low.
The boot_sel pins should never be shorted, the jumper must be moved or
a lower value resistor used to change the pull (existing resistors are 4k7, 1k should work)
To install with the stock bootloader you must break the built in image selection process
which uses at least the following vars: f_upgrade_addr, f_upgrade2_addr, loadaddr, kernel_addr, activeregion, committedregion
This is done by setting loadaddr and both f_upgrade_addr vars to the same address:
VR9 # setenv loadaddr 0xB0040000
VR9 # setenv f_upgrade_addr 0xB0040000
VR9 # setenv f_upgrade2_addr 0xB0040000
VR9 # saveenv
Then flash the firmware image:
VR9 # tftpboot 0x81000000 lede-lantiq-xrx200-ASL56026-squashfs-sysupgrade.bin
VR9 # erase B0040000 +${filesize}
VR9 # cp.b 0x81000000 0xB0040000 ${filesize}
Signed-off-by: Alex Maclean <monkeh@monkeh.net>
The VGV7510KW22BRN and VGV7519BRN do not have the same brnImage
signature. It was accidentally changed with ba42c1d ("lantiq: un-macro
the image building code").
Signed-off-by: Mathias Kresin <dev@kresin.me>
The following commit changed the build templates name but forgot to
update the TARGET_DEVICES variable properly.
commit f9226158be (lantiq: rename EASY98000 to EASY98000NOR)
Signed-off-by: John Crispin <john@phrozen.org>
This moves the extraction of the eeprom/calibration data to a hotplug
firmware script. Additionally it modifies all .dts to configure ath9k
directly from within the .dts.
The owl-loader approach enables support on devices with exotic eeprom
data locations (such as unaligned positions on the flash or data
inside an UBI volume).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
[add ath9k caldata mac address patcher]
[fixes DGN3500 wifi mac]
[fixes BTHOMEHUBV3A wifi mac]
[set invalid mac for BTHOMEHUB2B, FRITZ3370, FRITZ7320 & FRITZ7360SL to restore previous random mac behavior]
Signed-off-by: Mathias Kresin <dev@kresin.me>
This adds support for the Intel Falcon SoC for GPON.
Support for the Falcon SoC was removed in commit c821836395 svn rev:
40392 from OpenWrt, this commit adds it again.
This patch adds a new subtarget for the Falcon SoC, but it still misses
all the drivers needed to control the GPON part.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The DEVICE_PACKAGES are not included in the initramfs image in case
TARGET_PER_DEVICE_ROOTFS is set. This might produces initramfs images
with a not working network configuration because of a missing swconfig.
Workaround the issues by adding the essential swconfig package to the
default packages selection and deselect swconfig for boards not having
swconfig included before via device packages.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Use the new image build code and remove the lzma loader. The lzma
loader was used to cheat the signature validation of the bootloader and
I found another way to do this.
To migrate boards already using LEDE/OpenWrt to the new image the
following steps need to be done once:
VR9 # run reset_uboot_config
VR9 # reset
VR9 # setenv ethaddr AA:BB:CC:DD:EE:FF
VR9 # setenv preboot ping 1.1.1.1\;bootm 0xb001f000
VR9 # saveenv
VR9 # tftp 0x81000000 lede-lantiq-xrx200-VG3503J-squashfs-sysupgrade.bin
VR9 # erase 0xb0020000 $(filesize)
VR9 # cp.b 0x81000000 0xb0020000 $(filesize)
The mac address is printed on the label at the bottom of the case.
The following steps are need to be done during first install:
VR9 # setenv preboot ping 1.1.1.1\;bootm 0xb001f000
VR9 # saveenv
VR9 # tftp 0x81000000 lede-lantiq-xrx200-VG3503J-squashfs-sysupgrade.bin
VR9 # erase 0xb0020000 $(filesize)
VR9 # cp.b 0x81000000 0xb0020000 $(filesize)
The image uses the uImage firmware splitter now instead of hardcoded
kernel and rootfs partitions. The firmware partition size was extended
to use flash space that was reserved for partitions required only by
the ECI firmware.
Due to the changes an upgrade to a later LEDE revision from a running
LEDE is supported now.
A default switch config was added and the device uses the same MAC
addresses as the ECI firmware now instead of the same for all VG3503J.
Signed-off-by: Mathias Kresin <dev@kresin.me>
This makes init.d script handle existing UCI entries using the new
trigger. It also switches all targets to use its package.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
The WBMR boards are the only ones in the whole tree selecting the wpad
and hostapd-utils package by default.
Remove the wps uci-default script as well, there is no obvious reason
why the wps config need to be set only for this board.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Due to the introduced double whitespace the default package selection
isn't applied. This leads to errors like a not working networking
because of a missing swconfig binary.
Fixes FS#208.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Add USB led aliases to boards having an led which is meant to be used
as USB led according to the manuals.
Remove the kmod-ledtrig-usbdev from the default package selection for
boards not having an USB led. Add the kmod-ledtrig-usbdev to boards
where it is missing.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Device/AVM unconditionally inherits Device/NAND, which changes the
sysupgrade image to sysupgrade-tar (instead of a "raw" sysupgrade image
as used in the Device/Default template).
This moves the Device/NAND call to the FRITZ3370 device definition, as
this is the only AVM/EVA device that uses NAND.
Additionally we have to define the IMAGE_SIZE for the AVM/EVA NOR
devices to ensure that the images are not discarded.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
By default USB LEDs are associated with usbdev trigger. However,
not all devices which have USB LEDs have kmod-ledtrig-usbdev in their
list of default packages. Add it to the relevant devices.
Signed-off-by: Matti Laakso <matti.laakso@outlook.com>
Now that the "sysupgrade-nand" step is used by non-NAND targets as well,
rename it to "sysupgrade-tar" to make it more generic.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Both devices were converted to the new image build code but still using
the LegacyDevice define. Therefore an image isn't created for the
mentioned devices.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Specifying the device profile in PROFILES is unnecessary, and for all
devices the DEVICE_PROFILE variable matched the device name.
Get rid of this useless variable and set DEVICE_DTS to $(1)
Signed-off-by: Felix Fietkau <nbd@nbd.name>
It is used by a core build template, so the variable should be
initialized and added to DEVICE_VARS in the core.
Same for DEVICE_DTS_DIR
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Ethernet, ADSL2+ and LEDs are fully functional.
Supporting the two TAE ports and SIP gateway was not attempted.
The WiFi is unreliable, due to experimental support for rt35xx family
devices by the rt2800pci driver.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
[rebase to LEDE HEAD]
[switch to normal image instead of brnboot image]
[remove not required pinmux child nodes keys, leds, ebu, exin, pci_in and pci_out]
[remove switch_rst pinmux child node (no support for hw reset in driver/setting a default GPIO value in DT]
[enable usage of the wireless LED]
[fixup mac address configuration]
Sgned-off-by: Mathias Kresin <dev@kresin.me>
This image format is used by Lantiq's / Intel's UGW version 6.1 to 7.1.
These images can be flashed onto a board with the SoC vendor boot
loader as a replacement for the vendor firmware.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The *_UBIFS_OPTS variables need to be prefixed with DEVICE_ to match
the profile name.
The conditions need to be evaluated after the *_UBIFS_OPTS are set,
otherwise the variables are always empty.
Do not append or pass the DEVICE_ prefixed profile name to the images.
Use the name that is passed by the Image/Build/Profile/ step.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Alex Maclean
Felix Fietkau
Mathias Kresin
John Crispin
Hauke Mehrtens
Martin Blumenstingl
Ben Mulvihill
dpeddi
Eddi De Pieri
Rafał Miłecki
Matti Laakso
Jo-Philipp Wich
Oswald Buddenhagen
Ben Whitten