dumalogiya
/
openwrt
2
0
Fork 0
Code Issues Pull Requests Releases Wiki Activity

lantiq: rework VG3503J image

Browse Source 
Use the new image build code and remove the lzma loader. The lzma
loader was used to cheat the signature validation of the bootloader and
I found another way to do this.

To migrate boards already using LEDE/OpenWrt to the new image the
following steps need to be done once:

  VR9 # run reset_uboot_config
  VR9 # reset
  VR9 # setenv ethaddr AA:BB:CC:DD:EE:FF
  VR9 # setenv preboot ping 1.1.1.1\;bootm 0xb001f000
  VR9 # saveenv
  VR9 # tftp 0x81000000 lede-lantiq-xrx200-VG3503J-squashfs-sysupgrade.bin
  VR9 # erase 0xb0020000 $(filesize)
  VR9 # cp.b 0x81000000 0xb0020000 $(filesize)

The mac address is printed on the label at the bottom of the case.

The following steps are need to be done during first install:

  VR9 # setenv preboot ping 1.1.1.1\;bootm 0xb001f000
  VR9 # saveenv
  VR9 # tftp 0x81000000 lede-lantiq-xrx200-VG3503J-squashfs-sysupgrade.bin
  VR9 # erase 0xb0020000 $(filesize)
  VR9 # cp.b 0x81000000 0xb0020000 $(filesize)

The image uses the uImage firmware splitter now instead of hardcoded
kernel and rootfs partitions. The firmware partition size was extended
to use flash space that was reserved for partitions required only by
the ECI firmware.

Due to the changes an upgrade to a later LEDE revision from a running
LEDE is supported now.

A default switch config was added and the device uses the same MAC
addresses as the ECI firmware now instead of the same for all VG3503J.

Signed-off-by: Mathias Kresin <dev@kresin.me>
v19.07.3_mercusys_ac12_duma
Mathias Kresin 8 years ago
parent 0c3de24d92
commit 17094e9e64
3 changed files with 15 additions and 79 deletions
Show Stats Download Patch File Download Diff File

7
target/linux/lantiq/base-files/etc/board.d/02_network
Unescape Escape View File

@ -120,6 +120,13 @@ TDW8970|TDW8980)
"0:lan:2" "2:lan:3" "4:lan:4" "5:lan:1" "6t@eth0"
;;
VG3503J)
lan_mac=$(mtd_get_mac_ascii uboot-env ethaddr)
wan_mac=$(macaddr_add "$lan_mac" 1)
ucidef_add_switch "switch0" \
"2:lan:1" "4:lan:2" "6t@eth0"
;;
VR200v)
wan_mac=$(macaddr_add "$(mtd_get_mac_binary romfile 61696)" 1)
ucidef_add_switch "switch0" \

33
target/linux/lantiq/dts/VG3503J.dts
Unescape Escape View File

@ -42,37 +42,12 @@
};
partition@20000 {
label = "kernel";
reg = <0x20000 0x300000>;
};
partition@1a0000 {
label = "rootfs";
reg = <0x320000 0x420000>;
};
partition@740000 {
label = "btagent";
reg = <0x740000 0x80000>;
};
partition@7c0000 {
label = "pri_bfocus_cfg";
reg = <0x7c0000 0x10000>;
};
partition@7d0000 {
label = "sec_bfocus_cfg";
reg = <0x7d0000 0x10000>;
};
partition@7e0000 {
label = "sysconfig";
reg = <0x7e0000 0x10000>;
label = "firmware";
reg = <0x20000 0x7d0000>;
};
partition@7f0000 {
label = "misc_cfg";
label = "uboot-env";
reg = <0x7f0000 0x10000>;
};
};
@ -145,7 +120,7 @@
#address-cells = <1>;
#size-cells = <0>;
reg = <0>;
mac-address = [ 00 11 22 33 44 55 ];
lantiq,switch;
ethernet@2 {
compatible = "lantiq,xrx200-pdi-port";

54
target/linux/lantiq/image/Makefile
Unescape Escape View File

@ -22,17 +22,6 @@ else
UBIFS_OPTS := -m 2048 -e 126KiB -c 4096
endif
LOADER_MAKE := $(NO_TRACE_MAKE) -C lzma-loader KDIR=$(KDIR)
define Image/BuildLoader/Template
-rm -rf $(KDIR)/lzma-loader
$(LOADER_MAKE) LOADER=loader$(2)-$(1).bin\
LZMA_TEXT_START=0x80a00000 \
LOADADDR=0x80002000 \
LOADER_DATA="$(KDIR)/vmlinux$(2)-$(1).lzma" BOARD="$(1)" \
compile loader.bin
endef
define Build/eva-image
lzma2eva $(KERNEL_LOADADDR) $(KERNEL_LOADADDR) $@ $@.new
( dd if=$@.new bs=64k conv=sync; cat ./eva.dummy.squashfs; ) > $@
@ -98,12 +87,6 @@ define Image/BuildDGN3500B/squashfs
endef
define Image/BuildLoader/squashfs
dd if=$(KDIR)/loader-$(2).bin of=$(KDIR)/loader-$(2).bin.padded bs=3072k conv=sync
cat $(KDIR)/loader-$(2).bin.padded $(KDIR)/root.$(1) > $(BIN_DIR)/$(IMG_PREFIX)-$(2)-$(1).image
$(call prepare_generic_squashfs,$(BIN_DIR)/$(IMG_PREFIX)-$(2)-$(1).image)
endef
ifneq ($(CONFIG_TARGET_ROOTFS_INITRAMFS),)
define Image/BuildKernel/InitramfsTemplate
$(call PatchKernelLzma,$(1),-initramfs)
@ -119,32 +102,6 @@ define Image/BuildKernel/Template
$(Image/BuildKernel/InitramfsTemplate)
endef
ifneq ($(CONFIG_TARGET_ROOTFS_INITRAMFS),)
define Image/BuildKernelLoader/InitramfsTemplate
$(CP) $(KDIR)/loader-initramfs-$(1).bin $(BIN_DIR)/$(IMG_PREFIX)-$(1)-vmlinux-initramfs-loader
$(CP) $(KDIR)/vmlinux-initramfs-$(1) $(BIN_DIR)/$(IMG_PREFIX)-$(1)-vmlinux-initramfs
endef
endif
define Image/BuildKernelLoader/Template
$(CP) $(KDIR)/loader-$(1).bin $(BIN_DIR)/$(IMG_PREFIX)-$(1)-vmlinux-loader
$(CP) $(KDIR)/vmlinux-$(1) $(BIN_DIR)/$(IMG_PREFIX)-$(1)-vmlinux
$(Image/BuildKernelLoader/InitramfsTemplate)
endef
ifneq ($(CONFIG_TARGET_ROOTFS_INITRAMFS),)
define Image/Prepare/InitramfsTemplate
$(call PatchKernelLzma,$(1),-initramfs)
$(call Image/BuildLoader/Template,$(1),-initramfs)
endef
endif
define Image/Prepare/Template
$(call PatchKernelLzma,$(1))
$(call Image/BuildLoader/Template,$(1))
$(Image/Prepare/InitramfsTemplate)
endef
### Kernel scripts ###
define Build/mkbrncmdline
mkbrncmdline -i $@ -o $@.new BRN-BOOT
@ -623,14 +580,11 @@ define Device/FRITZ7360SL
endef
TARGET_DEVICES += FRITZ7360SL
Image/Prepare/Profile/VG3503J=$(call Image/Prepare/Template,VG3503J)
Image/BuildKernel/Profile/VG3503J=$(call Image/BuildKernelLoader/Template,VG3503J)
Image/Build/Profile/VG3503J=$(call Image/BuildLoader/$(1),$(1),VG3503J)
define LegacyDevice/VG3503J
DEVICE_TITLE := BT Openreak - ECI VDSL Modem
define Device/VG3503J
IMAGE_SIZE := 8000k
DEVICE_TITLE := BT OpenReach - ECI VDSL Modem
endef
LEGACY_DEVICES += VG3503J
TARGET_DEVICES += VG3503J
include tp-link.mk

Write Preview
Loading…
Cancel
Save