This replaces deprecated backticks by more versatile $(...) syntax.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
[add commit description]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This replaces deprecated backticks by more versatile $(...) syntax.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
[add commit description]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This package allows to read battery status information and control the
power state of the RAVPower RP-WD009 power management IC.
Signed-off-by: David Bauer <mail@david-bauer.net>
The RAVPower RP-WD009 is a batter-powered pocket sized router with SD
card lot and USB port.
Hardware
--------
CPU: MediaTek MT7628AN
RAM: 64M DDR2
FLASH: 16M GigaDevices SPI-NOR
WLAN: MediaTek MT7628AN 2T2R b/g/n
MediaTek MT7610E 1T1R n/ac
ETH: 1x FastEthernet
SD: SD Card slot
USB: USB 2.0
Custom PMIC on the I2C bus (address 0x0a).
Installation
------------
1. Press and hold down the reset button.
2. Power up the Device. Keep pressing the reset button for 10
more seconds until the Globe LED lights up.
3. Attach your Computer to the Ethernet port. Assign yourself the
address 10.10.10.1/24.
4. Access the recovery page at 10.10.10.128 and upload the OpenWrt
factory image.
5. The flashing will take around 1 minute. The device will reboot
automatically into OpenWrt.
Signed-off-by: David Bauer <mail@david-bauer.net>
This reverts commit 930f3c0148.
The build fails with the following build error:
arm-openwrt-linux-muslgnueabi-ld.bfd: drivers/built-in.o: in function `ide_init':
build_dir/target-arm_xscale_musl_eabi/u-boot-nsa310/u-boot-2020.04/drivers/block/ide.c:750: undefined reference to `ide_preinit'
make[4]: *** [Makefile:1700: u-boot] Error 1
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Removing i2c pxa slave
The i2c-pxa is typically not use in slave mode. It does not make sense
to have slave mode enabled by default.
Having slave mode enabled prevents the i2c controller from being reset
if a real slave device such as an SFP is attached to the i2c-pxa bus and
locks it up.
Disable slave mode so that the i2c controller can be reset if the bus is
locked up.
If someone actually has a need for pxa slave mode this can be enabled in
kernel config.
Signed-off-by: Scott Roberts <ttocsr@gmail.com>
/lib/netifd/dhcp.script:
Keep support for 'timesvr' while also supporting 'timesrv'
Add log message indicating deprecation of 'timesvr'
Signed-off-by: Sukru Senli <sukru.senli@iopsys.eu>
the uboot of nsa310 cannot use the network chip
as it is a realtek on the PCIe lanes and not a
Marvell ethernet from the SoC.
Therefore tftp is not possible on this device
and the only way to install is by loading files
from a USB drive.
If the USB subsystem is dead there is no way to
install OpenWrt.
Enable sata support and commands so it can be
used as a fallback in case of USB issues.
Signed-off-by: Alberto Bursi <bobafetthotmail@gmail.com>
With package "coreutil-sha256sum" installed "sysupgrade" fails to perform 'sha256sum -s' and instead returns 'invalid option -- 's''.
This is caused due to:
different syntax for a sha256sum status check ('sha256sum --status' with "coreutil-sha256sum")
'/usr/bin/sha256sum' being symlinked to '/usr/bin/gnu-sha256sum' (after installation of "coreutil-sha256sum")
"coreutil-sha256sum" package from the packages feed replaces the Busybox sha256sum
This patch restores for 'sysupgrade' the busybox call to its sha256sum applet.
Signed-off-by: Huangbin Zhan <zhanhb88@gmail.com>
Remove leds-apu2 out of tree driver. There is a new upstream device gpio
and leds driver stack available for the APUv2 and APUv3 boards from pc
egnines. This new driver stack was add in kernel version 4.15.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
ath9k will already fallback on software-crypto for chipsets not
supporting IEEE802.11w (MFP). So advertising MFP is not dependent
on disabling HW crypto for all traffic entirely.
Tested on Sonicwall SonicPoint Ni (AR9132)
Signed-off-by: David Bauer <mail@david-bauer.net>
Backport patches which fix compile issue for uClibc-ng :
dbrandom.c:174:8: warning: implicit declaration of function 'getrandom'; did you mean 'genrandom'? [-Wimplicit-function-declaration]
ret = getrandom(buf, sizeof(buf), GRND_NONBLOCK);
^~~~~~~~~
genrandom
dbrandom.c:174:36: error: 'GRND_NONBLOCK' undeclared (first use in this function); did you mean 'SOCK_NONBLOCK'?
ret = getrandom(buf, sizeof(buf), GRND_NONBLOCK);
^~~~~~~~~~~~~
SOCK_NONBLOCK
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
- update SPDX license identifier
- use https in URL
- use default PKG_BUILD_DIR
Suggested-by: Josef Schlehofer <josef.schlehofer@nic.cz>
Tested-by: Josef Schlehofer <josef.schlehofer@nic.cz>
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* compat: drop centos 8.1 support as 8.2 is now out
Of note, as well, is that we now have both RHEL7 and RHEL8 in our CI at
<https://www.wireguard.com/build-status/>.
* Kbuild: remove -fvisibility=hidden from cflags
This fixes an issue when compiling wireguard as a module for ARM kernels in
THUMB2 mode without the JUMP11 workaround.
* noise: do not assign initiation time in if condition
Style fix.
* device: avoid circular netns references
Fixes a circular reference issue with network namespaces.
* netns: workaround bad 5.2.y backport
This works around a back backport in the 5.2.y series.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
mac80211_get_addr is called from mac80211_generate_mac, where the local variable
initialisation id="${macidx:-0}" suggests that macidx is not always defined.
Probably, idx was supposed to be used instead of $(($macidx + 1)).
Fixes: 4d99db168c ("mac80211: try to get interface addresses from wiphy sysfs 'addresses' if no mask is set")
Signed-off-by: Leon M. George <leon@georgemail.eu>
urandom-seed has a separate Makefile, we can safely remove the definition here.
Fixes: 27bfde9c9f ("base-files: move urandom seed bits into separate package")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
"[[" is a bash extension for test. As the ash-implementation is not
fully compatible we drop its usage.
This follows up 3519bf4976
As a result, we also need to move the and/or out of the test brackets.
Signed-off-by: Sven Roederer <devel-sven@geroedel.de>
[squash from two patches, adjust commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The original text was copy/pasted from some other package.
Adjust the package title and description to match the description
on the publishers page.
Signed-off-by: Catalin Patulea <catalinp@google.com>
[slightly adjust content and commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
- drop patches (applied upstream):
* 010-backport-change-address-logging.patch
* 020-backport-ed25519-support.patch
* 021-backport-chacha20-poly1305-support.patch
- backport patches:
* 010-backport-disable-toom-and-karatsuba.patch:
reduce dropbear binary size (about ~8Kb).
- refresh patches.
- don't bother anymore with following config options
because they are disabled in upstream too:
* DROPBEAR_3DES
* DROPBEAR_ENABLE_CBC_MODE
* DROPBEAR_SHA1_96_HMAC
- explicitly disable DO_MOTD as it was before commit a1099ed:
upstream has (accidentally) switched it to 0 in release 2019.77,
but reverted back in release 2020.79.
Signed-off-by: Konstantin Demin <rockdrilla@gmail.com>
This replace the shell script header of ldd
when it install to `/usr/bin/ldd` where
`#! /..../staging_dir/host/bin/bash`
should be
`#!/bin/sh`
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
Previously, gpio_switch only accepts GPIO pin number as input. Once a
GPIO pin is exported and named by device tree, its pin state cannot be
configured and saved across reboots by UCI.
This patch adds support for named GPIO pins. Thus GPIO pin can be
exported by device tree with active high/low correctly configured,
having human-readable name in /sys/class/gpio/ is also now possible.
More importantly, GPIO pins which are referenced by name will be immune
from pin mapping breakage while unintentional pin number changes are
introduced by kernel or driver updates.
Signed-off-by: Kuan-Yi Li <kyli@abysm.org>
This option allows adding the ath9k ADC register output as a source
of randomness into the Linux entropy pool at sufficient quality
random data (at least 10 bits and up to 22 bits of min-entropy for
a 32-bit value).
Fixes FS#1444
Signed-off-by: Alan Swanson <reiver@improbability.net>
Ubus patch as it seems have been broken by some rebase in the past as
the location of line that adds ubus object file was in condition for
CONFIG_MACSEC. That condition was adding object files that are not
touched by ubus patch. This means ubus.o does not have to be included in
that case. When it has to be and when build fails is when CONFIG_AP is
set. All files included in wpa_supplicant that are touched by this patch
are in this condition. This means that this is for sure the original
place for it.
Signed-off-by: Karel Kočí <karel.koci@nic.cz>
Removes the standalone implementation of stack smashing protection
in gcc's libssp in favour of the native implementation available
in glibc and uclibc. Musl libc already uses its native ssp, so this
patch does not affect musl-based toolchains.
Stack smashing protection configuration options are now uniform
across all supported libc variants.
This also makes kernel-level stack smashing protection available
for x86_64 and i386 builds using non-musl libc.
Signed-off-by: Ian Cooper <iancooper@hotmail.com>
After a hardware reconnect, the control device might be unavailable and
attempting to interact with it will lead to hanging gcom calls, leaving
the protocol setup in an unrecoverable state.
Change the protocol handler to bail out early and notify netifd if the
control device is not defined or if the underlying device node does not
exist.
Also ensure that the "disconnect", "connect" and "setmode" commands are
actually defined before trying to invoke them.
Finally attempt to re-query the device manufacturer if it is unset in
the interface state in order to prevent UNUPPORTED_MODEM errors after
a modem hardware reconnect.
Signed-off-by: Rozhuk Ivan <rozhuk.im@gmail.com>
[reword subject and commit message]
Ref: https://github.com/openwrt/openwrt/pull/2352
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Pass a default --up and --down executable to each started OpenVPN instance
which triggers /etc/hotplug.d/openvpn/ scripts whenever an instance
goes up or down.
User-configured up and down scripts are invoked by the default shipped
01-user hotplug handler to ensure that existing setups continue to work
as before.
As a consequence of this change, the up, down and script_security OpenVPN
options are removed from the option file, since we're always passing them
via the command line, they do not need to get included into the generated
configuration.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
[reword commit message, move hotplug executable to /usr/libexec]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
All devices are using nand images. Built-in MMC/SD modules are not needed
anymore.
Run tested: pogo v4
Reviewed-by: Sungbo Eo <mans0n@gorani.run>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
The sender domain has a DMARC Reject/Quarantine policy which disallows
sending mailing list messages using the original "From" header.
To mitigate this problem, the original message has been wrapped
automatically by the mailing list software.
Bringing up of station vlan fails if the optional mac entry isn't set.
The default mac "00:00:00:00:00:00", which should match all stations,
is mistakenly set to the non used variable "isolate". This results in
a wrong formatted .psk file which has to be "vlan_id mac key".
fixes: 5aa2ddd0: hostapd: add support for wifi-station and wifi-vlan sections
Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de>
SOC: IPQ4018 / QCA Dakota
CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7
DRAM: 256 MiB
NOR: 32 MiB
ETH: Qualcomm Atheros QCA8072 (2 ports)
USB: 1 x 2.0 (Host controller in the SoC)
WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2
WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2
INPUT: RESET Button
LEDS: White, Blue, Red, Orange
Flash instruction:
From EnGenius firmware to OpenWrt firmware:
In Firmware Upgrade page, upgrade your openwrt-ipq40xx-generic-engenius_emr3500-squashfs-factory.bin directly.
From OpenWrt firmware to EnGenius firmware:
1. Setup a TFTP server on your computer and configure static IP to 192.168.99.8
Put the EnGenius firmware in the TFTP server directory on your computer.
2. Power up EMR3500. Press 4 and then press any key to enter u-boot.
3. Download EnGenius firmware
(IPQ40xx) # tftpboot 0x84000000 openwrt-ipq40xx-emr3500-nor-fw-s.img
4. Flash the firmware
(IPQ40xx) # imgaddr=0x84000000 && source 0x84000000:script
5. Reboot
(IPQ40xx) # reset
Signed-off-by: Yen-Ting-Shen <frank.shen@senao.com>
[squashed update patch, updated to 5.4, dropped BOARD_NAME,
migrated to SOC]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
IPKG_INSTROOT is only set under image builder and we won't be running
this script at build time either, so remove the reference before it gets
cargo-culted into other scripts.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Acked-by: Hans Dedecker <dedeckeh@gmail.com>
The folder for the uci-defaults file of this package is wrong, so
the file most probably has not been executed at all for several
years at least.
Fix the folder and remove the useless shebang for the file.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The Netgear WNDRMAC v1 is a hardware variant of the Netgear WNDR3700 v2
Specifications
==============
* SoC: Atheros AR7161
* RAM: 64mb
* Flash on board: 16mb
* WiFi: Atheros AR9220 (a/n), Atheros AR9223 (b/g/n)
* Ethernet: RealTek RTL8366SR (1xWAN, 4xLAN, Gigabit)
* Power: 12 VDC, 2.5 A
* Full specs on [openwrt.org](https://openwrt.org/toh/hwdata/netgear/netgear_wndrmac_v1)
Flash Instructions
==================
It is possible to use the OEM Upgrade page to install the `factory`
variant of the firmware.
After the initial upgrade, you will need to telnet into the router
(default IP 192.168.1.1) to install anything. You may install LuCI
this way. At this point, you will have a web interface to configure
OpenWRT on the WNDRMAC v1.
Please use the `sysupgrade` variant for subsequent flashes.
Recovery Instructions
=====================
A TFTP-based recovery flash is possible if the need arises. Please refer
to the WNDR3700 page on openwrt.org for details.
https://openwrt.org/toh/netgear/wndr3700#troubleshooting_and_recovery
Signed-off-by: Renaud Lepage <root@cybikbase.com>
[update DTSI include name]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Bump to latest Git and refresh all patches in order to get fix for "UPnP
SUBSCRIBE misbehavior in hostapd WPS AP" (CVE-2020-12695).
General security vulnerability in the way the callback URLs in the UPnP
SUBSCRIBE command are used were reported (VU#339275, CVE-2020-12695).
Some of the described issues may be applicable to the use of UPnP in WPS
AP mode functionality for supporting external registrars.
Ref: https://w1.fi/security/2020-1/
Signed-off-by: Petr Štetiar <ynezz@true.cz>
d13290b Fix advertised IPv6 addresses
Don't just serve link-local addresses via mdns, offer all.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
When bringing up wifi the first time after boot, these warnings appear:
netifd: radio0 (1370): rm: can't remove '/var/run/hostapd-wlan0.psk': No such file or directory
netifd: radio0 (1370): rm: can't remove '/var/run/hostapd-wlan0.vlan': No such file or directory
Silence them by adding the "-f" option to rm.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: John Crispin <john@phrozen.org>
This updates to the last firmware version before the switch to building
from the common firmware branch, which introduces various issues.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: Álvaro Fernández Rojas <noltari@gmail.com>
Hans Dedecker
Álvaro Fernández Rojas
Rui Salvaterra
David Bauer
Hauke Mehrtens
Scott Roberts
Sukru Senli
Alberto Bursi
Huangbin Zhan
Florian Eckert
Sungbo Eo
Jason A. Donenfeld
Leon M. George
Sven Roederer
Catalin Patulea
Konstantin Demin
Chen Minqiang
Kuan-Yi Li
Alan Swanson
Karel Kočí
Ian Cooper
Rozhuk Ivan
Daniel Golle
Pawel Dembicki
Johann Neuhauser
Yen-Ting-Shen
Stijn Tintel
Kevin Darbyshire-Bryant
Adrian Schmutzler
Renaud Lepage
Felix Fietkau
Christian Lamparter
Petr Štetiar