This fixes a few cosmetic issues with partition offset and size
that are inconsistent probably due to copy/pasting.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Pressing the 'WLAN' button should enable/disable wireless activity.
Currently, the button is mapped to the KEY_WLAN, which will not
have this effect.
This patch changes the mapping of the WLAN button, so a button
press will emit an action for the 'rfkill' key instead of 'wlan'.
Apparently, this is what stock OpenWRT expects.
This fix is analogous to the preceding patch for Fritzbox 3370.
Signed-off-by: Dustin Gathmann <dzsoftware@posteo.org>
The WLAN button actions are reversed, i.e. pressing the button emits a
'released' action, and vice versa.
This can easily be checked by adding
logger -t button_action "$BUTTON $ACTION"
as the second line of /etc/rc.button/rfkill, and using logread to read
the events (assuming the preceding patch has been applied).
Defining the GPIO as ACTIVE_LOW corrects this behavior.
Signed-off-by: Dustin Gathmann <dzsoftware@posteo.org>
Pressing the 'WLAN' button should enable/disable wireless activity.
However, on the Fritzbox 3370 this doesn't have an effect.
This patch changes the mapping of the physical WLAN button, so a button
press will emit an action for the 'rfkill' key instead of 'wlan'.
Apparently, this is what stock OpenWRT expects, and also what is
implemented for most other devices.
Signed-off-by: Dustin Gathmann <dzsoftware@posteo.org>
This fixes the gphy LED pins for Zyxel P-2812 devices. The have
been accidentally altered during a tidy-up operation (see Fixes:
below).
No ports were available, dmesg reported:
[ 0.658577] pinctrl-xway 1e100b10.pinmux: pin io5 already requested by
1e100bb0.stp; cannot claim for 1e108000.eth
[ 0.667566] pinctrl-xway 1e100b10.pinmux: pin-5 (1e108000.eth) status -22
[ 0.685238] lantiq,xrx200-net 1e108000.eth: Error applying setting,
reverse things back
[ 0.693270] lantiq,xrx200-net: probe of 1e108000.eth failed with error -22
Fixes: FS#3188
Fixes: 660200e53d ("lantiq: dts: assign the GPHY LED pins to the
Ethernet controller node")
Suggested-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: Willem van den Akker <wvdakker@wilsoft.nl>
[commit message facelift]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Fix inconsistencies found in DTS files and sort ethernet ports based on
updated names.
Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
[squash two separate patches, rephrase commit title/message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The removed lines are already included in vr9_avm_fritz736x.dtsi
Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
[rephrase commit title/message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Move the USB VBUS regulator nodes out of the GPIO controller node. This
fixes a problem where the "regulator-fixed" driver wasn't probed for
these regulators because the GPIO driver doesn't scan the child-nodes
and based on the dt-bindings documentation it's not supposed to.
This fixed the following error reported by Luca Olivetti:
...
dwc2 1e101000.usb: DWC OTG Controller
dwc2 1e101000.usb: new USB bus registered, assigned bus number 1
dwc2 1e101000.usb: irq 62, io mem 0x1e101000
dwc2 1e101000.usb: startup error -517
dwc2 1e101000.usb: USB bus 1 deregistered
dwc2 1e101000.usb: dwc2_hcd_init() FAILED, returning -517
Fixes: FS#1634
Cc: Luca Olivetti <luca@ventoso.org>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Set wifi mac from flash partition 'board_config' to
match the label on the device (Easybox 802).
Currently the wifi mac is always set to 00:0c:43:28:60:00.
eth0 and WiFi will now share the same mac (as in original firmware).
Signed-off-by: Lars Wessels <software@bytebox.org>
[improve commit message]
Signed-off-by: David Bauer <mail@david-bauer.net>
The fritz 7312 does not support 1000 gbit. Advertising it makes it
worse. Some NIC will change to 1000 gibt and turn off and on again for
ever.
The previous patch in 36f628910b was only applied to the 4.19 file,
so let's just make it consistent with this patch.
Cc: Alexander Couzens <lynxis@fe80.eu>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Use similiar naming scheme as ath79.
Since the fritz 7360 v2 was only in the tree for 2 days, there
is no compatibility for the old image.
Users which has installed the fritz 7360 v2 before this change, must
use sysupgrade --force to skip checks on the board.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Reviewed-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This commit adds support for the Fritzbox 7360v2
CPU: VR9 500MHz Cores: 2
RAM: 128 MB
NOR-Flash: 32 MB
WLAN: AR9287-BL1A
DECT is not working.
Thanks Sebastian Ortwein for adding 7360SL.
The dts file is derived from avm_fritz7360sl.dts.
Firmware can be flashed with this method:
1.) Set your client IP to 192.168.178.2
2.) Power on your your Fritzbox and connect to 192.168.178.1
via ftp in the first 5 seconds.
3.) login with adam2/adam2
4.) type into the ftp prompt:
passive
binary
debug 1
quote MEDIA FLSH // (not FLASH)
put openwrt-lantiq-xrx200-avm_fritz7360v2-squashfs-sysupgrade.bin mtd1
// using the correct location for the squashfs-sysupgrade-firmware.bin
5.) wait till red light flashing turns off.
6.) type: exit
Run tested with kernel 4.19 and 5.4 on Fritzbox 7360 V2.
Issue:
Ethernet speed is slow, (iperf between a Xiaomi mir3g
and this router results in <80Mbits throughput
with a wired cable when using the gbit ports.)
Signed-off-by: Yushi Nishida <kyro2man@gmx.net>
Switch to the mainline Lantiq PCIe PHY driver and update the vr9.dtsi
accordingly.
The Lantiq IRQ SMP support added upstream required changes to the SoC
dtsi as well.
Following changes are made to the Lantiq kernel patches:
0005-lantiq_etop-pass-struct-device-to-DMA-API-functions.patch
0006-MIPS-lantiq-pass-struct-device-to-DMA-API-functions.patch
applied upstream
0008-MIPS-lantiq-backport-old-timer-code.patch
access_ok API update because it lost it's type (which was the first)
parameter in upstream commit 96d4f267e40f95 ("Remove 'type' argument
from access_ok() function")
0024-MIPS-lantiq-autoselect-soc-rev-matching-fw.patch
merged into 0026-MIPS-lantiq-Add-GPHY-Firmware-loader.patch
0024-MIPS-lantiq-revert-DSA-switch-driver-PMU-clock-chang.patch
revert upstream changes required for upstream xrx200 ethernet and
xrx200 (DSA) switch driver but breaking our driver
0026-MIPS-lantiq-Add-GPHY-Firmware-loader.patch
required for our driver but dropped upstream, add former upstream
version
0028-NET-lantiq-various-etop-fixes.patch
now has to use the phy_set_max_speed API instead of modifying
phydev->supported. Also call ltq_dma_enable_irq() in
ltq_etop_open() based on upstream commit cc973aecf0b054 ("MIPS:
lantiq: Do not enable IRQs in dma open")
Signed-off-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
This is referenced in two .dts but never actually used from userspace.
Drop support for this property because it's not used and because it
makes updating to Linux 5.4 harder (as the patch doesn't apply anymore).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Duplicate kernel 4.19 config and patches for kernel 5.4.
Duplicate the devicetree source files as well, they need kernel 5.4
specific adjustments.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Adrian Schmutzler
Dustin Gathmann
Willem van den Akker
Aleksander Jan Bajkowski
Martin Blumenstingl
Lars Wessels
Alexander Couzens
Yushi Nishida
Mathias Kresin