At this moment Linksys EA8500 uses only eth0.
This patch change switch registers, which allow to use eth1 as lan
and eth0 as wan. The method work with similar Linksys EA7500V1
and it work with EA8500.
Suggested-by: Sungbo Eo <mans0n@gorani.run>
Tested-by: Brian Onn <brian.a.onn@gmail.com>
Tested-by: Adrian Panella <ianchi74@outlook.com>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
This patch adds support for the Linksys EA7500 V1 router.
Specification:
- CPU: Qualcomm IPQ8064
- RAM: 256MB
- Flash: NAND 128MB
- WiFi: QCA9982 an+ac + QCA9983 bgn
- Ethernet: 5 GBE Ports (WAN+ 4xLAN) (QCA8337)
- USB: 1x USB 3.0 1x USB2.0
- Serial console: RJ-45 115200 8n1 (1V8 Voltage level)
- 2 Buttons
- 1 LED
Known issues:
- Some devices won't flash via web gui
Installation:
- Newer stock images doesn't allow to install custom firmware.
- Please downgrade software to 1.1.2 version. Official firmware:
https://downloads.linksys.com/downloads/firmware/FW_EA7500_1.1.2.172843_prod.gpg.img
- Do it two times to downgrade all stored images.
- Apply factory image via web-gui.
Serial + TFTP method:
- downgrade to 1.1.2 two times
- connect ehternet and serial cable
- set ip address of tftp server to 192.168.1.254
- put openwrt factory image to tftp folder and rename it to macan.bin
- stop device while booting in u-boot
- run command: "run flashimg"
- run command: "setenv boot_part 1"
- run command "saveenv"
- reset
Back to stock:
- Please use old non-gpg image like this 1.1.2:
https://downloads.linksys.com/downloads/firmware/FW_EA7500_1.1.2.172843_prod.img
- ssh to router and copy image to tmp
- use sysupgrade -n -F
Tested by github users: @jack338c and @grzesiczek1
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
[removed i2c4_pins, mdio0_pins, nand_pins, rgmii2_pins from DTSI]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This drops the shebang from all target files for /lib and
/etc/uci-defaults folders, as these are sourced and the shebang
is useless.
While at it, fix the executable flag on a few of these files.
This does not touch ar71xx, as this target is just used for
backporting now and applying cosmetic changes would just complicate
things.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
WG2600HP has its WLAN MAC addresses at PRODUCTDATA 0xc and 0x12, so
use them both directly.
Signed-off-by: Yanase Yuki <dev@zpc.sakura.ne.jp>
[commit title/message clarification]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The default case will catch anything left, there is no need to
explicitly add any device to it.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
With this commit, the WAN LED is triggered by the switch port state
instead of the eth0 netdev.
Otherwise, the LED is always illuminated, regardless of the WAN port
link state.
Signed-off-by: David Bauer <mail@david-bauer.net>
While all ath10k eeproms have a checksum field, so far two
functions for patching ath10k MAC address have been present (and
been used).
This merges code to provide a single function ath10k_patch_mac
in caldata.sh, having its name in accordance with ath9k functions.
By doing so, correct MAC patching for current and future ath10k
devices should be ensured.
This patch adds checksum adjustments for several targets on
ath79 and lantiq.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This unifies MAC address patch functions and moves them to a
common script. While those were implemented differently for
different targets, they all seem to do the same. The number of
different variants is significantly reduced by this patch.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This moves the almost identical calibration data extraction
functions present multiple times in several targets to a single
library file /lib/functions/caldata.sh.
Functions are renamed with more generic names to merge different
variants that only differ in their names.
Most of the targets used find_mtd_chardev, while some used
find_mtd_part inside the extraction code. To merge them, the more
abundant version with find_mtd_chardev is used in the common code.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
[rebase on latest master; add mpc85xx]
Signed-off-by: David Bauer <mail@david-bauer.net>
The xor() function is defined in each of the caldata extraction
scripts for several targets. Move it to functions.sh to reduce
duplicate code.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
It's a variable set by procd that should replace hardcoded
/tmp/sysupgrade.tgz.
This change requires the most recent procd with the commit 0f3c136
("sysupgrade: set UPGRADE_BACKUP env variable").
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
$CONF_TAR shouldn't be assumed to always point to the sysupgrade.tgz.
This change makes code more generic and allows refactoring $CONF_TAR.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
1) Add BACKUP_FILE and use it when copying an archive to be restored
after sysupgrade (on the next preinit).
2) Use CONF_TAR for copying backup prepared by the /sbin/sysupgrade
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This commit made the following changes to sync all bootcount scripts:
1. use boot() instead of start()
This script only needs to be executed once when boot is complete.
use boot() to make this explicit.
2. drop sourcing of /lib/functions.sh
This is aready done in /etc/rc.common.
3. ramips: replace board name checking with a case
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
This changes size and offset set for WiFi caldata extraction and
MAC address adjustment to hexadecimal notation.
This will be much clearer for the reader when numbers are big, and
will also match the style used for mtd-cal-data in DTS files.
Since dd cannot deal with hexadecimal notation, one has to convert
back to decimal by simple $(($hexnum)).
Acked-by: Alexander Couzens <lynxis@fe80.eu>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This changes the offsets for the MAC address location in
mtd_get_mac_binary* and mtd_get_mac_text to hexadecimal notation.
This will be much clearer for the reader when numbers are big, and
will also match the style used for mtd-mac-address in DTS files.
(e.g. 0x1006 and 0x5006 are much more useful than 4102 and 20486)
Acked-by: Alexander Couzens <lynxis@fe80.eu>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
1) nand_do_upgrade() is always called by a target code
2) nand_do_upgrade() starts with calling platform_nand_pre_upgrade()
It means there is no need for the platform_nand_pre_upgrade() callback
at all. All code that was present there could bo moved & simplly called
by a target right before the nand_do_upgrade().
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Consistently handle boot-count reset and upgrade across
ipq40xx, ipq806x, kirkwood, mvebu
Dual-firmware devices often utilize a specific MTD partition
to record the number of times the boot loader has initiated boot.
Most of these devices are NAND, typically with a 2k erase size.
When this code was ported to the ipq40xx platform, the device in hand
used NOR for this partition, with a 16-byte "record" size. As the
implementation of `mtd resetbc` is by-platform, the hard-coded nature
of this change prevented proper operation of a NAND-based device.
* Unified the "NOR" variant with the rest of the Linksys variants
* Added logging to indicate success and failure
* Provided a meaningful return value for scripting
* "Protected" the use of `mtd resetbc` in start-up scripts so that
failure does not end the boot sequence
* Moved Linksys-specific actions into common `/etc/init.d/bootcount`
For upgrade, these devices need to determine which partition to flash,
as well as set certain U-Boot envirnment variables to change the next
boot to the newly flashed version.
* Moved upgrade-related environment changes out of bootcount
* Combined multiple flashes of environment into single one
* Current-partition detection now handles absence of `boot_part`
Runtime-tested: Linksys EA8300
Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[checkpatch.pl fixes, traded split strings for 80+ chars per line]
NEC WG2600HP uses port1 on QCA8337 as a WAN port, so "0x2" should
be used as a portmask instead of "0x1e" for "WAN" LED configuration.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Buffalo WXR-2533DHP is a 2.4/5 GHz band 11ac router, based on Qualcomm
IPQ8064.
The U-Boot on WXR-2533DHP employs a complicated dual firmware
protection scheme against corruptions of the kernel and rootfs
images. See the notes in buffalo.sh for details.
specifications:
- Qualcomm IPQ8064 (384 - 1,400 MHz, 2C2T)
- 512 MB of RAM (DDR3)
- 256 MB of Flash (NAND)
- 4T4R 2.4/5 GHz Wlan (QCA9980)
- 5x 10/100/1000 Mbps Ethernet
- 10x LEDs, 8x keys (6x buttons, 2x slide-switches)
- 2x USB 3.0 Type-A
- 12VDC/4A AC Adapter
- UART through-hole on PCB
- J3: Vcc, GND, TX, RX from USB port side
- 115200n8
Boot instructions for the initramfs image:
1. Prepare the TFTP server with the initramfs image renamed to
"wxr2300dhp-initramfs.uImage" and IP address "192.168.11.10".
2. Press the "AOSS" button while powering on the WXR-2533DHP.
3. Wait until the "Wireless" LED flashes before releasing the AOSS button.
The WXR-2533DHP will grab the image from TFTP server and will boot it.
Flashing instructions:
To persistently write the firmware, flash an openwrt sysupgrade image
from inside the initramfs, for example transfer
via `scp <sysupgrade> root@192.168.1.1:/tmp` and flash on the device
with `sysupgrade -n /tmp/<sysupgrade>`. Then wait ~120 seconds to
let it finish the flashing process.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [reworded message]
Ben Greear reported in his patch:
|Subject: netgear r7800: Fix mac address of radios.
|
|Reloading the driver causes the phyX to change, and that
|caused the MAC address to change.
This is because all ODM/OEMs except QCA bothered to write
the correct MAC address for the ath10k wifi into the
calibration data.
This patch copies over the MAC patching helper functions from ipq40xx's
target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
file and converts all the devices to patch the correct MACs into the
extracted calibration data before it gets sent to the driver, which sets
up the device with the correct MAC address. It also removes the entries
in the 10_fix_wifi_mac file as they have served their purpose for good.
Please note the C2600: There is conflicting information on what
the offset for the second wifi is supposed to be. This patch uses
what was specified in 10_fix_wifi_mac.
According to Ben Greear this method is save to use with the
stock firmware too. As he explained that the stock firmware
messes up rx-bssid mask calculation when the MAC is changed
after the first vif is created.
Reported-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
I wanted to add status LEDs support to my imx6 based board and have found out,
that I could use diag.sh script found in ramips platform, which seems to be
also shared in a few other platforms:
4801276bc2078c5bcf03003c831e3b0a target/linux/ramips/base-files/etc/diag.sh
4801276bc2078c5bcf03003c831e3b0a target/linux/ipq40xx/base-files/etc/diag.sh
4801276bc2078c5bcf03003c831e3b0a target/linux/ath79/base-files/etc/diag.sh
And @chunkeey suggested to me, that I can also add lantiq, ipq806x and
apm821xx to the list of platforms which could share this generic
diag.sh.
I've extended the base diag.sh in a way, that if it detects any of the
DTS LED aliases, then it would use the generic DTS set_led_state code.
The code in platform's diag.sh has moved to base-files package in this
commit:
base-files: diag.sh: Make it more generic towards DTS so it could be reused
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Tested-by: Christian Lamparter <chunkeey@gmail.com> (apm821xx and ipq40xx)
Specification:
- SoC: Qualcomm Atheros IPQ8064 ARM-v7 Dual Core SMP CPU
- RAM: 512MB DDR3 System Memory
- NOR Flash: 32MB SPI NOR
- NAND Flash: 256MB NAND
- Ethernet: 5 x 1G via QCA8337N
- USB: 2 x USB 3.0 SuperSpeed
- PCIe: 3x Mini PCIe 2.0 Slots
Three PCIE2.0 connectors can connect two or three radio cards
such as the CUS260 for 2.4 GHz WLAN and the CUS239 for 802.11ac WLAN
How to flash via u-boot console:
tftpboot 0x44000000 openwrt-ipq806x-qcom_ipq8064-ap161-squashfs-nand-factory.bin
nand erase 0x1340000 0x4000000
nand write 0x44000000 0x1340000 $filesize
setenv bootargs ‘console=ttyMSM0,115200 ubi.mtd=ubi root=/dev/ubiblock0_1’
saveenv
bootm
Further upgrades via sysupgrade.
Tested on IPQ8064 AP161 Board:
1) NAND boot
2) Tested USB and PCIe interfaces
3) WDOG test
4) cpu frequency scaling
5) ethernet, 2G and 5G WiFi
6) ubi sysupgrade
Signed-off-by: Ram Chandra Jangir <rjangir@codeaurora.org>
This way the radio (phy) name can be the same through module reloads.
To set the desired name:
uci set wireless.@wifi-device[0].phyname=wiphy0
I guess this only works on ipq6086 boards as I could not find a more
generic place to put this. Maybe someone can improve it.
Signed-off-by: Ben Greear <greearb@candelatech.com>
The upgrade led is only used if a running led is defined. If no running
led is defined, the upgrade led is ignored and upgrade isn't indicated
at all.
Instead, turn off the running led prior to turning the upgrade led on.
In most cases there isn't any visual change, but it allows to use an
independent led for upgrade indication.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Set the (sys)upgrade state when sourcing the stage2 script instead of
setting the state for each target individual.
This change fixes the, due to a missing state set, not working upgrade
led on ath79 and apm821xx.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Netgear R7800 switch LAN ports are numbered backwards in LuCI,
i.e. numbering is not corresponding to the actual physical port labels,
patch fixes that.
Signed-off-by: Aleksandr V. Piskunov <aleksandr.v.piskunov@gmail.com>
[merged with existing board using the same config]
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
The original device support patch configured the amber wlan LEDs (which
are meant as error indicator by the OEM) controlled by the SOC's GPIO
as wlan traffic indicators, as the correct white wlan LEDs are
connected to GPIOs controlled by the QCA9984/ ath10k wlan cards were
not accessible. The recent addition of GPIO/ LED support to ath10k now
makes it possible to use the correct white LEDs instead - and
"mac80211: ath10k: use tpt LED trigger by default" also enables them by
default. While both LEDs are independent of each other (two separate
LEDs sharing one light tunnel), triggering both on wlan traffic is not
the intended behaviour (bright yellow light).
Tested on the ZyXEL NBG6817.
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
NEC Aterm WG2600HP is a 2.4/5 GHz band 11ac router, based on Qualcomm
IPQ8064.
Specification:
- IPQ8064 (384 - 1,400 MHz)
- 512 MB of RAM
- 32 MB of Flash (SPI)
- 4T4R 2.4/5 GHz
- 5x 10/100/1000 Mbps Ethernet
- 12x LEDs, 4x keys
- 1x USB 3.0 Type-A
- UART header on PCB
- RX, TX, NC, GND, Vcc from power connector side
- baudrate: 115200 bps
Flash instruction using initramfs image:
1. Connect serial cable to UART header
2. Connect power cable and turn on the router
3. When the "Press the [f] key and hit [enter] to enter failsafe mode"
message is displayed on the console, press the "f" key and Enter key
sequentially to enter the failsafe mode
4. create fw_env.config file with following contents on failsafe mode:
/dev/mtd9 0x0 0x10000 0x10000
5. Execute following commands to add and change the environment
variables of U-Boot
fw_setenv ipaddr "192.168.0.1"
fw_setenv serverip "192.168.0.2"
fw_setenv autostart "yes"
fw_setenv bootcmd "tftpboot 0x44000000 wg2600hp-initramfs.bin;
bootipq"
6. Set the IP address of the computer to 192.168.0.2, connect to the LAN
port of WG2600HP, and start the TFTP server on the computer
7. Rename OpenWrt initramfs image for WG2600HP to
"wg2600hp-initramfs.bin" and place it in the TFTP directory
8. Remove power cable from WG2600HP, reconnect it and restart WG2600HP
9. WG2600HP downloads initramfs image from TFTP server on the computer,
loads it and boot with initramfs image
10. On the initramfs image, execute "mtd erase firmware" to erase stock
firmware and execute sysupgrade with the sysupgrade image
11. Wait ~180 seconds to complete flashing
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Hardware highlights:
- SoC: Qualcomm Atheros IPQ8064/5 ARM Dual Core CPU
- RAM: (512MB or 1GB) DDR3 System Memory
- Storage: 32MB NOR (Cypress S25FL256S1)
256MB NAND (Micron MT29F2G08ABBEAH4)
- Ethernet: 5 x 1G via QCA8337N
- USB: 1 x USB 2.0/3.0 + 1 x USB 2.0 on mini PCIe3 socket
- PCIe: 3x mini PCIe (third mini PCIE3 is PCIe/USB shared)
- SIM Card Slot: 2 x Slot
- Buttons: Reset Button
- LEDs: 18x, 8x GPIO controllable
- Buzzer
The correct amount of RAM will be passed by the bootloader.
In contrast to the documentation provided by Compex, the third PCIe
doesn't use GPIO16 for PERST. Instead, GPIO3 is shared and used as PERST
for PCIe0 and PCIe2.
So far, no one was able to get USB 3.0 working with the 1GB RAM version,
while it works fine for my 512MB version. Since USB 3.0 doesn't work with
the Compex firmware for the 1G variant either, it could be a hardware
issue with these boards.
OpenWrt will be installed to the NAND flash. Make sure to have a full
working image on the NOR flash. It will be the backup in case anything
goes wrong.
It has been observed that an image loaded via tftpboot might have
bitflips. Hence the extra step to create a crc32 checksum to allow to
compare the checksum with the one from the source file prior to flashing.
In all cases it is necessary to set the following u-boot parameter to an
empty (whitespace) value, to ensure that the chosen bootargs of the dts
isn't overwritten or set to bogus - not working - values:
(IPQ) # set bootargs " "
(IPQ) # set fsbootargs " "
(IPQ) # saveenv
The sysupgrade image can be installed directly on flash using u-boot (put
jumper in JP13 (leave JP9 open) to boot from nand):
(IPQ) # set serverip 192.168.1.20
(IPQ) # set ipaddr 192.168.1.1
(IPQ) # tftpboot 0x42000000 openwrt-ipq806x-compex_wpq864-squashfs-nand-factory.bin
(IPQ) # crc32 0x42000000 $filesize
(IPQ) # nand erase 0x1340000 0x4000000
(IPQ) # nand write 0x42000000 0x1340000 $filesize
The initramfs image can be started using:
(IPQ) # set fdt_high 0x48000000
(IPQ) # tftpboot 0x44000000 openwrt-ipq806x-compex_wpq864-initramfs-fit-uImage.itb
(IPQ) # bootm 0x44000000
Signed-off-by: Christian Mehlis <christian@m3hlis.de>
Signed-off-by: Mathias Kresin <dev@kresin.me>
This patch adds support for GL.iNet GL-B1300
Specification:
- SOC: IPQ4028 / QCA Dakota
- RAM: 256 MiB
- FLASH: 32 MiB
- ETH: Qualcomm Atheros QCA8075 Gigabit Switch (2 x LAN, 1 x WAN)
- USB: 1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC)
- WLAN1: Qualcomm Atheros QCA4028 2.4GHz 802.11bgn 2:2x2
- WLAN2: Qualcomm Atheros QCA4028 5GHz 802.11a/n/ac 2:2x2
- INPUT: one reset and one WPS button
- LEDS: 3 leds: Power, WIFI(only for 2.4G currently), and one reserved
- UART: 1 x UART on PCB (3.3V, TX, RX, GND) - 115200 8N1
Installation:
Method 1:
- use serial port to stop uboot
- uboot command: run lf
Method 2:
- push down reset button and power on
- wait until three leds constantly on then release
- upgrade by uboot web at http://192.168.1.1
Note:
- the sysupgrade image need to be renamed to lede-gl-b1300.bin in both method.
- the sysupgrade image can be automatically downloaded if tftp server at
192.168.1.2 have that file.
- the wifi led will be flashing when writing image.
Signed-off-by: Dongming Han <handongming@gl-inet.com>
Instead of writing to the currently booted partition set, this
implements full dual-boot support for sysupgrade by always writing to
the other, currently inactive, partition set and toggling the dualflag
after a successful flash.
The currently active/ booted partition set is determined by parsing
/proc/cmdline for its rootfs parameter (supplied by the DTS), instead
of reading from the 0:DUAL_FLAG mtd, in order to prevent (potentially)
bricking both partition sets.
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Instead of hardcoding /dev/loop0, it's safer to query for the first
free loop device and assign that dynamically. While /dev/loop0 is a
reasonable assumption immediately following "losetup --detach-all",
detaching the mounted overlay is no longer strictly necessary once
dual-boot support has been added for the nbg6817.
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Harmonize the variable usage for $kernel and $rootfs to always contain
the full device path, instead of just its basename.
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
This commit marks the CPUs switchport explicit as untagged.
Otherwise, an eth0.1 interface is created and the devices
LAN-ports are not working.
Signed-off-by: David Bauer <mail@david-bauer.net>
Use the first found directory in the tar archive instead of relying on
a directory named according to the userspace boardname.
It allows to change the boardname without adding another compatibility
layer to the zyxel sysupgrade.
Fixes: 33f09cf151 ("ipq806x: convert to dt-based board-detection")
Signed-off-by: Mathias Kresin <dev@kresin.me>
* QCA IPQ401x
* 256 MB of RAM
* 32 MB of SPI NOR flash (s25fl256s1)
- 2x 15 MB available; but one of the 15 MB regions is the recovery image
* 2T2R 2.4 GHz
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=16,variant=OM-A42
* 2T2R 5 GHz
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=17,variant=OM-A42
* multi-color LED (controlled via red/green/blue GPIOs)
* 1x button (reset; kmod-input-gpio-keys compatible)
* external watchdog
- triggered GPIO
* 1x USB (xHCI)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x gigabit ethernet
* powered only via POE
- 802.3af POE on Ethernet 1
- 18-24v passive POE (mode B) on Ethernet 2
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the factory image to the u-boot when the device boots up.
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
Use the generic board detection method:
- Board name: First compatible string from the device tree
- Board model: Model property from the device tree
Change occurrences of board name in userspace by the compatible
string, and removed target specific board detection script
Replace the definition of SUPPORTED_DEVICES in Device/Default
to extract the dt compatible string from each device definition.
Additionally, for devices supported by lede-17.01, append
the value of BOARD_NAME to SUPPORTED_DEVICES in the device
definition.
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
This will allow to maintain the current syntax for LEDs config
when switching to a device tree compatible string boardname.
None of the current boards use a comma in the boardname, so they
will be unaffected.
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Lantiq and IPQ806X (which includes IPQ40XX) both define the
same custom function {ipq806x|lantiq}_get_dt_led.
This patch moves the function into the base-file package at
lib/functions/leds.sh to make it more accessible for other
targets as well.
Cc: Mathias Kresin <dev@kresin.me>
Cc: John Crispin <john@phrozen.org>
Cc: Hannu Nyman <hannu.nyman@iki.fi>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
AP-DK01.1-C1 is QCA dev board with:
- ipq4018 quad core ARM @716.8MHz, 2x2 dual (11n+11ac) radio
- 256MB RAM
- 32MB SPI flash
- QCA8075 multiport ethernet phy (WAN port, 4x LAN ports)
First installation via u-boot:
sf probe
sf erase 0x180000 0x1a00000
tftpboot 0x84000000 lede-ipq806x-AP-DK01.1-C1-squashfs-sysupgrade.bin
sf write 0x84000000 0x180000 $filesize
Further upgrades via sysupgrade.
Changes:
- add partitions
- set memory size to 256MB
- add reserved memory mapping
- add correct compatible string
- add image generation
- extract pre-cal data from ART partition
Compile and run tested.
Wirespeed NAT can be achieved with spreading rx interrupts over different
cores. Wifi speed is ~550Mbps @5GHz in open air.
Note:
AP-DK01.1-C1 is fully compatible with AP-DK01.2-C1, which has
ipq4028 instead of ipq4018 on board.
Changes since v2:
- based on dts(i) rework/cleanup submitted:
http://lists.infradead.org/pipermail/lede-dev/2017-October/009596.html
- precise reserved memory mapping
- more precise description
- compatible string
Signed-off-by: Roman Yeryomin <roman@advem.lv>
The ZyXEL NBG6817 calculates all MAC addresses based on the ethaddr
value stored in the U-Boot environment (0:APPSBLENV). No MAC addresses
are stored in the ART partition and the generated MAC addresses for the
wlan interfaces alternate randomly between 12:34:56:78:90:12 and
00:03:7f:12:34:56.
interface new/ OEM MAC old MAC
wlan-2.4g (phy1): ethaddr undefined
wlan-5g (phy0): ethaddr + 1 undefined
lan : ethaddr + 2 ethaddr
wan : ethaddr + 3 ethaddr + 1
This patch defines stable MAC addresses for the wlan interfaces for
the first time instead of generating them at random. The previously
defined values for lan/ wan are changed to follow the settings of the
OEM firmware.
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
The order of LAN ports shown in Luci is reversed compared to what is
written on the case of the device. Fix the order so that they match.
Signed-off-by: Baptiste Jonglez <git@bitsofnetworks.org>
Do not parse /tmp/sysinfo/board_name, /proc/cpuinfo or the device tree
compatible string directly. Always use the board_name function to get
the board name.
The admswconfig package still reads /proc/cpuinfo directly. The code
looks somehow broken and the whole adm5120 which uses this package
looks unmaintained. Leave it as it is for now.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Pawel Dembicki
Adrian Schmutzler
Samantha Collard
Yanase Yuki
David Bauer
Rafał Miłecki
Chuanhong Guo
Jeff Kletsky
INAGAKI Hiroshi
Christian Lamparter
Petr Štetiar
Ram Chandra Jangir
Ben Greear
Mathias Kresin
Aleksandr V. Piskunov
Stefan Lippers-Hollmann
Christian Mehlis
John Crispin
Dongming Han
Sven Eckelmann
Luis Araneda
Roman Yeryomin
Baptiste Jonglez