ipq806x: add support for GL.iNet GL-B1300
This patch adds support for GL.iNet GL-B1300 Specification: - SOC: IPQ4028 / QCA Dakota - RAM: 256 MiB - FLASH: 32 MiB - ETH: Qualcomm Atheros QCA8075 Gigabit Switch (2 x LAN, 1 x WAN) - USB: 1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC) - WLAN1: Qualcomm Atheros QCA4028 2.4GHz 802.11bgn 2:2x2 - WLAN2: Qualcomm Atheros QCA4028 5GHz 802.11a/n/ac 2:2x2 - INPUT: one reset and one WPS button - LEDS: 3 leds: Power, WIFI(only for 2.4G currently), and one reserved - UART: 1 x UART on PCB (3.3V, TX, RX, GND) - 115200 8N1 Installation: Method 1: - use serial port to stop uboot - uboot command: run lf Method 2: - push down reset button and power on - wait until three leds constantly on then release - upgrade by uboot web at http://192.168.1.1 Note: - the sysupgrade image need to be renamed to lede-gl-b1300.bin in both method. - the sysupgrade image can be automatically downloaded if tftp server at 192.168.1.2 have that file. - the wifi led will be flashing when writing image. Signed-off-by: Dongming Han <handongming@gl-inet.com>v19.07.3_mercusys_ac12_duma
Dongming Han
6 years ago
committed by
John Crispin
parent
88a41074e8
commit
04d3308b62
Binary file not shown.
@ -0,0 +1,316 @@
|
||||
/* Copyright (c) 2015, The Linux Foundation. All rights reserved.
|
||||
*
|
||||
* Permission to use, copy, modify, and/or distribute this software for any
|
||||
* purpose with or without fee is hereby granted, provided that the above
|
||||
* copyright notice and this permission notice appear in all copies.
|
||||
*
|
||||
* THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
|
||||
* WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
|
||||
* MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
|
||||
* ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
|
||||
* WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
|
||||
* ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
|
||||
* OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
|
||||
*
|
||||
*/
|
||||
|
||||
#include "qcom-ipq4019.dtsi"
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
#include <dt-bindings/soc/qcom,tcsr.h>
|
||||
|
||||
/ {
|
||||
model = "GL.iNet GL-B1300";
|
||||
compatible = "glinet,gl-b1300", "qcom,ipq4019";
|
||||
|
||||
memory {
|
||||
device_type = "memory";
|
||||
reg = <0x80000000 0x10000000>;
|
||||
};
|
||||
|
||||
reserved-memory {
|
||||
#address-cells = <0x1>;
|
||||
#size-cells = <0x1>;
|
||||
ranges;
|
||||
|
||||
apps_bl@87000000 {
|
||||
reg = <0x87000000 0x400000>;
|
||||
no-map;
|
||||
};
|
||||
|
||||
sbl@87400000 {
|
||||
reg = <0x87400000 0x100000>;
|
||||
no-map;
|
||||
};
|
||||
|
||||
cnss_debug@87500000 {
|
||||
reg = <0x87500000 0x600000>;
|
||||
no-map;
|
||||
};
|
||||
|
||||
cpu_context_dump@87b00000 {
|
||||
reg = <0x87b00000 0x080000>;
|
||||
no-map;
|
||||
};
|
||||
|
||||
tz_apps@87b80000 {
|
||||
reg = <0x87b80000 0x280000>;
|
||||
no-map;
|
||||
};
|
||||
|
||||
smem@87e00000 {
|
||||
reg = <0x87e00000 0x080000>;
|
||||
no-map;
|
||||
};
|
||||
|
||||
tz@87e80000 {
|
||||
reg = <0x87e80000 0x180000>;
|
||||
no-map;
|
||||
};
|
||||
};
|
||||
|
||||
soc {
|
||||
tcsr@194b000 {
|
||||
/* select hostmode */
|
||||
compatible = "qcom,tcsr";
|
||||
reg = <0x194b000 0x100>;
|
||||
qcom,usb-hsphy-mode-select = <TCSR_USB_HSPHY_HOST_MODE>;
|
||||
status = "ok";
|
||||
};
|
||||
|
||||
ess_tcsr@1953000 {
|
||||
compatible = "qcom,tcsr";
|
||||
reg = <0x1953000 0x1000>;
|
||||
qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
|
||||
};
|
||||
|
||||
tcsr@1949000 {
|
||||
compatible = "qcom,tcsr";
|
||||
reg = <0x1949000 0x100>;
|
||||
qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
|
||||
};
|
||||
|
||||
tcsr@1957000 {
|
||||
compatible = "qcom,tcsr";
|
||||
reg = <0x1957000 0x100>;
|
||||
qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
|
||||
};
|
||||
|
||||
pinctrl@1000000 {
|
||||
serial_pins: serial_pinmux {
|
||||
mux {
|
||||
pins = "gpio60", "gpio61";
|
||||
function = "blsp_uart0";
|
||||
bias-disable;
|
||||
};
|
||||
};
|
||||
|
||||
spi_0_pins: spi_0_pinmux {
|
||||
pinmux {
|
||||
function = "blsp_spi0";
|
||||
pins = "gpio55", "gpio56", "gpio57";
|
||||
};
|
||||
pinmux_cs {
|
||||
function = "gpio";
|
||||
pins = "gpio54";
|
||||
};
|
||||
pinconf {
|
||||
pins = "gpio55", "gpio56", "gpio57";
|
||||
drive-strength = <12>;
|
||||
bias-disable;
|
||||
};
|
||||
pinconf_cs {
|
||||
pins = "gpio54";
|
||||
drive-strength = <2>;
|
||||
bias-disable;
|
||||
output-high;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
blsp_dma: dma@7884000 {
|
||||
status = "ok";
|
||||
};
|
||||
|
||||
spi_0: spi@78b5000 {
|
||||
pinctrl-0 = <&spi_0_pins>;
|
||||
pinctrl-names = "default";
|
||||
status = "ok";
|
||||
cs-gpios = <&tlmm 54 0>;
|
||||
};
|
||||
|
||||
serial@78af000 {
|
||||
pinctrl-0 = <&serial_pins>;
|
||||
pinctrl-names = "default";
|
||||
status = "ok";
|
||||
};
|
||||
|
||||
cryptobam: dma@8e04000 {
|
||||
status = "ok";
|
||||
};
|
||||
|
||||
crypto@8e3a000 {
|
||||
status = "ok";
|
||||
};
|
||||
|
||||
watchdog@b017000 {
|
||||
status = "ok";
|
||||
};
|
||||
|
||||
usb3_ss_phy: ssphy@9a000 {
|
||||
status = "ok";
|
||||
};
|
||||
|
||||
usb3_hs_phy: hsphy@a6000 {
|
||||
status = "ok";
|
||||
};
|
||||
|
||||
usb3: usb3@8af8800 {
|
||||
status = "ok";
|
||||
};
|
||||
|
||||
usb2_hs_phy: hsphy@a8000 {
|
||||
status = "ok";
|
||||
};
|
||||
|
||||
usb2: usb2@60f8800 {
|
||||
status = "ok";
|
||||
};
|
||||
|
||||
mdio@90000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
ess-switch@c000000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
ess-psgmii@98000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
edma@c080000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
wifi@a000000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
wifi@a800000 {
|
||||
status = "okay";
|
||||
};
|
||||
};
|
||||
|
||||
gpio-keys {
|
||||
compatible = "gpio-keys";
|
||||
|
||||
wps {
|
||||
label = "wps";
|
||||
gpios = <&tlmm 5 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_WPS_BUTTON>;
|
||||
};
|
||||
reset {
|
||||
label = "reset";
|
||||
gpios = <&tlmm 63 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_RESTART>;
|
||||
};
|
||||
};
|
||||
|
||||
gpio-leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
power {
|
||||
label = "gl-b1300:green:power";
|
||||
gpios = <&tlmm 4 GPIO_ACTIVE_HIGH>;
|
||||
default-state = "on";
|
||||
};
|
||||
mesh {
|
||||
label = "gl-b1300:green:mesh";
|
||||
gpios = <&tlmm 3 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
wlan {
|
||||
label = "gl-b1300:green:wlan";
|
||||
gpios = <&tlmm 2 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&spi_0 {
|
||||
mx25l25635f@0 {
|
||||
compatible = "mx25l25635f", "jedec,spi-nor";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
reg = <0>;
|
||||
spi-max-frequency = <24000000>;
|
||||
|
||||
SBL1@0 {
|
||||
label = "SBL1";
|
||||
reg = <0x0 0x40000>;
|
||||
read-only;
|
||||
};
|
||||
MIBIB@40000 {
|
||||
label = "MIBIB";
|
||||
reg = <0x40000 0x20000>;
|
||||
read-only;
|
||||
};
|
||||
QSEE@60000 {
|
||||
label = "QSEE";
|
||||
reg = <0x60000 0x60000>;
|
||||
read-only;
|
||||
};
|
||||
CDT@c0000 {
|
||||
label = "CDT";
|
||||
reg = <0xc0000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
DDRPARAMS@d0000 {
|
||||
label = "DDRPARAMS";
|
||||
reg = <0xd0000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
APPSBLENV@e0000 {
|
||||
label = "APPSBLENV";
|
||||
reg = <0xe0000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
APPSBL@f0000 {
|
||||
label = "APPSBL";
|
||||
reg = <0xf0000 0x80000>;
|
||||
read-only;
|
||||
};
|
||||
ART@170000 {
|
||||
label = "ART";
|
||||
reg = <0x170000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
kernel@180000 {
|
||||
label = "kernel";
|
||||
reg = <0x180000 0x400000>;
|
||||
};
|
||||
rootfs@580000 {
|
||||
label = "rootfs";
|
||||
reg = <0x580000 0x1a80000>;
|
||||
};
|
||||
firmware@180000 {
|
||||
label = "firmware";
|
||||
reg = <0x180000 0x1e80000>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&gmac0 {
|
||||
qcom,phy_mdio_addr = <4>;
|
||||
qcom,poll_required = <1>;
|
||||
qcom,forced_speed = <1000>;
|
||||
qcom,forced_duplex = <1>;
|
||||
vlan_tag = <2 0x20>;
|
||||
};
|
||||
|
||||
&gmac1 {
|
||||
qcom,phy_mdio_addr = <3>;
|
||||
qcom,poll_required = <1>;
|
||||
qcom,forced_speed = <1000>;
|
||||
qcom,forced_duplex = <1>;
|
||||
vlan_tag = <1 0x10>;
|
||||
};
|
||||
Loading…
Reference in New Issue