There is md5 sum of whole image embedded in combined-image header which
is checked on sysupgrade. The check will fail for ath79 images which
may have embedded metadata. This is because metadata are appended after
the combined image is created. To allow smooth transition from ar71xx to
ath79, strip metadata before calculating md5 sum for whole image.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
(cherry picked from commit 8b4109c2b4)
Now that $UPGRADE_BACKUP is set conditionally there is no need to check
the $UPGRADE_OPT_SAVE_CONFIG anymore. All conditions can be simplified.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit a858db3136)
It's a variable set by procd that should replace hardcoded
/tmp/sysupgrade.tgz.
This change requires the most recent procd with the commit 0f3c136
("sysupgrade: set UPGRADE_BACKUP env variable").
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 641f6b6c26)
stage2 passes image path to platform_do_upgrade() as an argument so it
can be simply accessed using $1
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 8b4bc7abe0)
[rmilecki: dropping ARGV without this change broke sysupgrade]
Fixes: 6ac62c4b6c ("base-files: don't set ARGV and ARGC")
That was a result of accidentally running "sed" twice on some files.
Fixes: 9b9412d55c ("treewide: replace remaining (not working now) $SAVE_CONFIG uses")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 1078de96e3)
This var has been replaced by the $UPGRADE_OPT_UPGRADE_OPT_SAVE_CONFIG
Fixes: f25d164aca ("base-files: pass "save_config" option to the "sysupgrade" method")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 5797fe84a3)
CPU: AR9342 SoC
RAM: 64 MB DDR2
Flash: 8 MB NOR SPI
Ports: 100 MBit (24V PoE in)
WLAN: 2.4/5 GHz
UART: 1 UART on PCB marked as J1 with 115200 8N1 config
LEDs: Power, Ethernet, 4x RSSI LEDs (orange, red, 2x green)
Buttons: Reset
UART connection details
.---------------------------------.
| |
[ETH] J1 [ANT]
| o VCC o RX o TX o GND |
`---------------------------------'
Flashing instructions using recovery method over TFTP
1. Unplug the ethernet cable from the router.
2. Using paper clip press and hold the router's reset button. Make sure
you can feel it depressed by the paper clip. Do not release the button
until step 4.
3. While keeping the reset button pressed in, plug the ethernet cable
back into the AP. Keep the reset button depressed until you see the
device's LEDs flashing in upgrade mode (alternating LED1/LED3 and
LED2/LED4), this may take up to 25 seconds.
4. You may release the reset button, now the device should be in TFTP
transfer mode.
5. Set a static IP on your Computer's NIC. A static IP of 192.168.1.25/24
should work.
6. Plug the PoE injector's LAN cable directly to your computer.
7. Start tftp client and issue following commands:
tftp> binary
tftp> connect 192.168.1.20
tftp> put openwrt-ar71xx-generic-ubnt-bullet-m-xw-squashfs-factory.bin
Tested only on Bullet M2HP.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Looks identical to the v2.
This PR adds support for a popular low-cost 2.4GHz N based AP
Specifications:
- SoC: Qualcomm Atheros QCA9533 (650MHz)
- RAM: 64MB
- Storage: 8 MB SPI NOR
- Wireless: 2.4GHz N based built into SoC 2x2
- Ethernet: 1x 100/10 Mbps, integrated into SoC, 24V POE IN
Installation:
Flash factory image through stock firmware WEB UI
or through TFTP
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP adress:192.168.0.254
Tested-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Robert Marko <robimarko@gmail.com>
[Rebased, adjusted for separate tplink-safeloader entry, dynamic partitioning]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The Mikrotik RouterBOARD SXT 2nD r3 is an outdoor WiFi AP / CPE
with a single 2.4 GHz radio and a 100 Mbps Ethernet port.
The device similar to the SXT 2nD r2, but it has SPI NOR flash instead
of NAND flash.
Hardware
--------
CPU: Atheros AR9344 (600 MHz)
RAM: 64 MiB
FLASH: 16 MiB SPI NOR W25Q128
ETH: 1x 100 Mbps Atheros AG71xx
WiFi: 2T2R 802.11b/g/n (ath9k)
Power: Passive PoE 8-30 V
Installation instructions:
1. Boot openwrt-ar71xx-mikrotik-vmlinux-initramfs.elf using a
DHCP+TFTP server.
2. Erase the "firmware" partition using the mtd command. This should
no longer be required once this patch is merged.
3. Use sysupgrade to install to flash. The file
openwrt-ar71xx-mikrotik-rb-nor-flash-16M-squashfs-sysupgrade.bin
should be used.
Signed-off-by: Xavier Douville <github@douville.org>
The install_bin from /lib/upgrade/common.sh is no longer creating the
symlinks when a secondary parameter is added. But the fw_setenv program was
always copied this way to the ramdisk for the upgrade.
Instead, this should be done using RAMFS_COPY_* like on all other
platforms.
Fixes: 438dcbfe74 ("base-files: automatically handle paths and symlinks for RAMFS_COPY_BIN")
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Adds Support for the TP-LINK CPE510 V2.0 by TP-Link.
The hardware is almost the same as the CPE510 V1.0
Follow the same processes as for the CPE510 V1.0
Signed-off-by: Andrew Cameron <apcameron@softhome.net>
TP-Link Archer C59v2 is a dual-band AC1350 router based on
Qualcomm/Atheros QCA9561+QCA9886 chips.
Specification:
- 775/650/258 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 2T2R 5 GHz
- 5x 10/100 Mbps Ethernet
- USB 2.0 port
- UART header on PCB
Flash instruction:
- via web UI:
1. Download openwrt-ar71xx-generic-archer-c59-v2-squashfs-factory.bin
2. Login to router and open the Advanced tab
3. Navigate to System Tools -> Firmware Upgrade
4. Upload firmware using the Manual Upgrade form
- via TFTP:
1. Set PC to fixed ip address 192.168.0.66
2. Download openwrt-ar71xx-generic-archer-c59-v2-squashfs-factory.bin
and rename it to tp_recovery.bin
3. Start a tftp server with the file tp_recovery.bin in its root directory
4. Turn off the router
5. Press and hold Reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time
the firmware should be transferred from the tftp server
8. Wait ~30 second to complete recovery.
Signed-off-by: Keith Maika <keithm@aoeex.com>
Qxwlan E750G v8 is based on Qualcomm QCA9344.
Specification:
- 560/450/225 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 8/16 MB of FLASH (SPI NOR)
- 2T2R 2.4G GHz (AR9344)
- 2x 10/100 Mbps Ethernet (PoE support)
- 2x 10/100/1000 Mbps Ethernet
- 7x LED (6 driven by GPIO)
- 1x button (reset)
- 1x DC jack for main power input (9-48 V)
- UART (J23) and LEDs (J2) headers on PCB
Flash instruction (using U-Boot CLI and tftp server):
- Configure PC with static IP 192.168.1.10 and tftp server.
- Rename "sysupgrade" filename to "firmware.bin" and place it in tftp
server directory.
- Connect PC with one of RJ45 ports, power up the board and press
"enter" key to access U-Boot CLI.
- Use the following command to update the device to OpenWrt: "run lfw".
Flash instruction (using U-Boot web-based recovery):
- Configure PC with static IP 192.168.1.xxx(2-254)/24.
- Connect PC with one of RJ45 ports, press the reset button, power up
the board and keep button pressed for around 6-7 seconds, until LEDs
start flashing.
- Open your browser and enter 192.168.1.1, select "sysupgrade" image
and click the upgrade button.
Signed-off-by: 张鹏 <sd20@qxwlan.com>
Qxwlan E750A v4 is based on Qualcomm QCA9344.
Specification:
- 560/450/225 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 8/16 MB of FLASH (SPI NOR)
- 2T2R 5G GHz (AR9344)
- 2x 10/100 Mbps Ethernet (one port with PoE support)
- 1x miniPCIe slot (USB 2.0 bus only)
- 7x LED (6 driven by GPIO)
- 1x button (reset)
- 1x DC jack for main power input (9-48 V)
- UART (J23) and LEDs (J2) headers on PCB
Flash instruction (using U-Boot CLI and tftp server):
- Configure PC with static IP 192.168.1.10 and tftp server.
- Rename "sysupgrade" filename to "firmware.bin" and place it in tftp
server directory.
- Connect PC with one of RJ45 ports, power up the board and press
"enter" key to access U-Boot CLI.
- Use the following command to update the device to OpenWrt: "run lfw".
Flash instruction (using U-Boot web-based recovery):
- Configure PC with static IP 192.168.1.xxx(2-254)/24.
- Connect PC with one of RJ45 ports, press the reset button, power up
the board and keep button pressed for around 6-7 seconds, until LEDs
start flashing.
- Open your browser and enter 192.168.1.1, select "sysupgrade" image
and click the upgrade button.
Signed-off-by: 张鹏 <sd20@qxwlan.com>
Qxwlan E558 v2 is based on Qualcomm QCA9558 + AR8327.
Specification:
- 720/600/200 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 8/16 MB of FLASH (SPI NOR)
- 2T2R 2.4 GHz (QCA9558)
- 3x 10/100/1000 Mbps Ethernet (one port with PoE support)
- 4x miniPCIe slot (USB 2.0 bus only)
- 1x microSIM slot
- 5x LED (4 driven by GPIO)
- 1x button (reset)
- 1x 3-pos switch
- 1x DC jack for main power input (9-48 V)
- UART (JP5) and LEDs (J8) headers on PCB
Flash instruction (using U-Boot CLI and tftp server):
- Configure PC with static IP 192.168.1.10 and tftp server.
- Rename "sysupgrade" filename to "firmware.bin" and place it in tftp
server directory.
- Connect PC with one of RJ45 ports, power up the board and press
"enter" key to access U-Boot CLI.
- Use the following command to update the device to OpenWrt: "run lfw".
Flash instruction (using U-Boot web-based recovery):
- Configure PC with static IP 192.168.1.xxx(2-254)/24.
- Connect PC with one of RJ45 ports, press the reset button, power up
the board and keep button pressed for around 6-7 seconds, until LEDs
start flashing.
- Open your browser and enter 192.168.1.1, select "sysupgrade" image
and click the upgrade button.
Signed-off-by: 张鹏 <sd20@qxwlan.com>
This patch adds support for the MikroTik RB931-2nD (hAP mini):
https://mikrotik.com/product/RB931-2nD
Specifications:
* SoC: Qualcomm QCA9533 (650MHz)
* RAM: 32MiB
* Storage: 16MiB SPI NOR flash
* Ethernet: 3x100M
* Wireless: QCA9533 built-in, dual-chain 802.11b/g/n
Installation:
1. Setup a DHCP/BOOTP Server with the following parameters:
* DHCP-Option 66 (TFTP server name): pointing to a local TFTP
server within the same subnet of the DHCP range
* DHCP-Option 67 (Bootfile-Name): matching the initramfs filename
of the to be booted image. The usable intramfs files are:
- openwrt-ar71xx-mikrotik-vmlinux-initramfs.elf
- openwrt-ar71xx-mikrotik-vmlinux-initramfs-lzma.elf
- openwrt-ar71xx-mikrotik-rb-nor-flash-16M-initramfs-kernel.bin
2. Press the reset button on the board and keep that pressed.
3. Connect the board to your local network via its Internet port.
4. Release the button after the LEDs on the board are turned off.
Now the board should load and start the initramfs image from
the TFTP server.
5. Now connect the board via either of its LAN ports (2 or 3).
6. Upload the sysupgrade image to the board with scp:
$ scp openwrt-ar71xx-mikrotik-rb-nor-flash-16M-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/fw.bin
7. Log in to the running system listening on 192.168.1.1 via ssh
as root (without password):
$ ssh root@192.168.1.1
8. Flash the uploaded firmware file from the ssh session via the
sysupgrade command:
root@OpenWrt:~# sysupgrade /tmp/fw.bin
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
Add support for detecting TP-Link Pharos v2 boards.
They use different format in product-info partition than v1 boards.
Code was written mostly by Alexander Couzens <lynxis@fe80.eu>
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
TP-Link Archer C7 v5 is a dual-band AC1750 router, based on Qualcomm/Atheros
QCA9563+QCA9880.
Specification:
- 750/400/250 MHz (CPU/DDR/AHB
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 3T3R 5 GHz
- 5x 10/100/1000 Mbps Ethernet
- 10x LED, 2x button
- UART header on PCB
Flash instruction:
1. Upload lede-ar71xx-generic-archer-c7-v5-squashfs-factory.bin via Web interface
Flash instruction using TFTP recovery:
1. Set PC to fixed ip address 192.168.0.66
2. Download lede-ar71xx-generic-archer-c7-v5-squashfs-factory.bin
and rename it to ArcherC7v5_tp_recovery.bin
3. Start a tftp server with the file tp_recovery.bin in its root directory
4. Turn off the router
5. Press and hold Reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time
the firmware should be transferred from the tftp server
8. Wait ~30 second to complete recovery.
Signed-off-by: Arvid E. Picciani <aep@exys.org>
This commit adds support for the Mikrotik wAP R (RBwAPR-2nD). The change
is based on 3b15eb0 which added support for the wAP 2nD. This change lacks
LED support.
Specifications:
- SoC: Qualcomm QCA9531 (650 MHz)
- RAM: 64 MB
- Storage: 16 MB NOR SPI flash
- Wireless: built-in QCA9531, 802.11b/g/n 2x2:2
- Ethernet: 1x100Mbps
- Power: 9-30V Passive PoE, 9-30V DC jack, 9-30V automotive jack
- SIM card slot
- Mini-PCIe slot
Installation:
1. Login to the Mikrotik WebUI to backup your licence key
2. Change the following settings in System->Routerboard->Settings:
- Boot device: try ethernet once then NAND
- Boot protocol: DHCP
- Force Backup Booter: checked
3. Setup a DHCP/BOOTP server with:
- DHCP-Option 66 (TFTP server name) pointing to a local TFTP
server within the same subnet of the DHCP range
- DHCP-Option 67 (Bootfile-Name) matching the initramfs filename
of the to be booted image, e.g.
openwrt-ar71xx-mikrotik-vmlinux-initramfs.elf
4. Power off the device
5. If this is the second attempt to boot OpenWRT or the boot device isn't
"try ethernet once then NAND," press and hold the reset button while
powered off. If this is the first attempt, this step isn't necessary.
6. Power on the device, holding the reset button for 15-20s if already
pressed from the previous step.
The board should load and start the initramfs image from the TFTP
server. Login as root/without password to the started OpenWRT via SSH
listing on IPv4 address 192.168.1.1. Use sysupgrade to install OpenWRT.
Revert to RouterOS
Use the "rbcfg" package on in OpenWRT:
- rbcfg set boot_protocol bootp
- rbcfg set boot_device ethnand
- rbcfg apply
Open Netinstall and reboot routerboard. Now Netinstall sees RouterBOARD
and you can install RouterOS. If NetInstall gets stuck on Sending offer
just wait for it to timeout and then close and open Netinstall again.
Click on install again.
In order for RouterOS to function properly, you need to restore license
for the device. You can do that by including license in NetInstall.
Signed-off-by: David Ehrmann <ehrmann@gmail.com>
This commit adds support for the AVM Fritz!WLAN Repeater 450E
SOC: Qualcomm QCA9556 (Scorpion) 560MHz MIPS74Kc
RAM: 64MB Zentel A3R12E40CBF DDR2
FLASH: 16MiB Winbond W25Q128 SPI NOR
WLAN1: QCA9556 2.4 GHz 802.11b/g/n 3x3
INPUT: WPS button
LED: Power, WiFi, LAN, RSSI indicator
Serial: Header Next to Black metal shield
Pinout is 3.3V - RX - TX - GND (Square Pad is 3.3V)
The Serial setting is 115200-8-N-1.
Tested and working:
- Ethernet
- 2.4GHz WiFi (correct MAC)
- Installation via EVA bootloader
- OpenWRT sysupgrade
- Buttons
- Most LEDs
Not working:
- 2 RSSI LEDs
AVM used for RSSI{0,1} two of the Ethernet PHYs LEDs which they
control over MDIO. Our driver doesn't expose these LEDs as GPIOs.
While it is possible to implement this feature, it would require an
additional kernel patch for a minor functionality.
Installation via EVA:
In the first seconds after Power is connected, the bootloader will
listen for FTP connections on 192.168.178.1. Firmware can be uploaded
like following:
ftp> quote USER adam2
ftp> quote PASS adam2
ftp> binary
ftp> debug
ftp> passive
ftp> quote MEDIA FLSH
ftp> put openwrt-sysupgrade.bin mtd1
Note that this procedure might take up to two minutes.
You need to powercycle the Device afterwards to boot OpenWRT.
Signed-off-by: David Bauer <mail@david-bauer.net>
This commit adds support for the OCEDO Koala
SOC: Qualcomm QCA9558 (Scorpion)
RAM: 128MB
FLASH: 16MiB
WLAN1: QCA9558 2.4 GHz 802.11bgn 3x3
WLAN2: QCA9880 5 GHz 802.11nac 3x3
INPUT: RESET button
LED: Power, LAN, WiFi 2.4, WiFi 5, SYS
Serial: Header Next to Black metal shield
Pinout is 3.3V - GND - TX - RX (Arrow Pad is 3.3V)
The Serial setting is 115200-8-N-1.
Tested and working:
- Ethernet
- 2.4 GHz WiFi
- 5 GHz WiFi
- TFTP boot from ramdisk image
- Installation via ramdisk image
- OpenWRT sysupgrade
- Buttons
- LEDs
Installation seems to be possible only through booting an OpenWRT
ramdisk image.
Hold down the reset button while powering on the device. It will load a
ramdisk image named 'koala-uImage-initramfs-lzma.bin' from 192.168.100.8.
Note: depending on the present software, the device might also try to
pull a file called 'koala-uimage-factory'. Only the name differs, it
is still used as a ramdisk image.
Wait for the ramdisk image to boot. OpenWRT can be written to the flash
via sysupgrade or mtd.
Due to the flip-flop bootloader which we not (yet) support, you need to
set the partition the bootloader is selecting. It is possible from the
initramfs image with
> fw_setenv bootcmd run bootcmd_1
Afterwards you can reboot the device.
Signed-off-by: David Bauer <mail@david-bauer.net>
PISEN TS-D084 is an wireless router with a battery and integrated power supply based on Atheros AR9331.
Specification:
- 400/400/200 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH (SPI NOR)
- 1x 10/100 Mbps Ethernet
- 1T1R 2.4 GHz (AR9331)
- 1x USB 2.0
Flash instruction:
The manufacturer are using exactly the same firmware header as TP-LINK TL-WR703N (including device ID!). Simply upload the factory firmware into WebUI and flashing is done.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
This commit adds support for the AVM Fritz!Box 4020 WiFi-router.
SoC: Qualcomm Atheros QCA9561 (Dragonfly) 750MHz
RAM: Winbond W971GG6KB-25
FLASH: Macronix MX25L12835F
WiFi: QCA9561 b/g/n 3x3 450Mbit/s
USB: 1x USB 2.0
IN: WPS button, WiFi button
OUT: Power LED green, Internet LED green, WLAN LED green,
LAN LED green, INFO LED green, INFO LED red
UART: Header Next to Black metal shield
Pinout is 3.3V - RX - TX - GND (Square Pad is 3.3V)
The Serial setting is 115200-8-N-1.
Tested and working:
- Ethernet (LAN + WAN)
- WiFi (correct MAC)
- Installation via EVA bootloader
- OpenWRT sysupgrade
- Buttons
- LEDs
Not working:
- USB port
Installation via EVA:
In the first seconds after Power is connected, the bootloader will
listen for FTP connections on 169.254.157.1 (Might also be 192.168.178.1). Firmware can be uploaded
like following:
ftp> quote USER adam2
ftp> quote PASS adam2
ftp> binary
ftp> debug
ftp> passive
ftp> quote MEDIA FLSH
ftp> put openwrt-sysupgrade.bin mtd1
Note that this procedure might take up to two minutes. After transfer is
complete you need to powercycle the device to boot OpenWRT.
Signed-off-by: David Bauer <mail@david-bauer.net>
Kernel support already present.
Patch adds userspace for the 'iLS' suffix model of the RB2011 family.
Enables correct initial switch settings, sysupgrade, etc.
https://mikrotik.com/product/RB2011iLS-IN
Signed-off-by: Simon Paterson <simon.paterson.nz@gmail.com>
Previously, tplink_pharos_check_image() would accept any image with ELF
magic and only non-printable data in the support-list, as in this case the
while-read loop would not run at all. Add the new support-list offset and
ensure an image is only accepted when the model string is actually found.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
TP-Link Archer C60 v2 is a dual-band AC1350 router, based on
Qualcomm/Atheros QCA9561 + QCA9886.
Specification:
- 775/650/258 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 2T2R 5 GHz
- 5x 10/100 Mbps Ethernet
- 7x LED, 2x button
- UART header on PCB
Flash instruction (web):
Download lede-ar71xx-generic-archer-c60-v2-squashfs-factory.bin and use
OEM System Tools - Firmware Upgrade site.
Flash instruction (recovery):
1. Set PC to fixed IP address 192.168.0.66
2. Download lede-ar71xx-generic-archer-c60-v2-squashfs-factory.bin and
rename it to tp_recovery.bin
3. Start a tftp server with the file tp_recovery.bin in its root
directory
4. Turn off the router
5. Press and hold reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time the firmware should
be transferred from the tftp server
8. Wait ~30 second to complete recovery
Flash instruction (under U-Boot, using UART):
tftp 0x81000000 lede-ar71xx-...-sysupgrade.bin
erase 0x9f030000 +$filesize
cp.b $fileaddr 0x9f030000 $filesize
reset
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
Add support for TL-WR940N v6 board. It is pretty much the same as v5
except they only left WAN LED and removed other ones.
Installation: flash factory image through WEB UI or use TFTP.
Signed-off-by: Robert Marko <robimarko@gmail.com>
D-Link DAP-1330 rev. A1 is a wall-plug N300 Wi-Fi range extender,
based on Qualcomm/Atheros QCA9533 v2.
Short specification:
- 650/393/216 MHz (CPU/DDR/AHB)
- 1x 10/100 Mbps Ethernet
- 64 MB of RAM (DDR1)
- 8 MB of FLASH
- 2T2R 2.4 GHz
- 2x external antennas
- 6x LED (2 are bi-color), 2x button
- 4 pin on pcb (looking from eth port and from left to right tx,rx,gnd,vcc)
Flash instruction: use "factory" image directly in vendor GUI.
This device has a recovery system that assign the ip addr of env
variable "serverip" via dhcp to a pc, and the "ipaddr" value to itself.
The recovery it's triggered by a not bootable firmware,
or pressing the reset button during the bootloader startup (first 30 seconds).
The recovery uses a http page to restore the firmware, and it's checking
the firmware image header, so use the "factory" image to
restore or the original firmware.
You can access vendor firmware over serial using:
- login: root
- password: linuxrocks
Image was tested only in EU version of the device, but should work
also with the same device version sold in other countries.
Signed-off-by: Nicolò Veronese <nicveronese@gmail.com>
GainStrong Oolite V5.2 is a small (39.5 x 78 mm), dual-band system on
module, based on Qualcomm QCA9531 + QCA9887. All QCA9531 SOC GPIOs are
available on castellated pins.
Specification:
- 650/400/200 MHz (CPU/DDR/AHB)
- 64/128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 5x 10/100 Mbps Ethernet (all ports available on castellated pins)
- 2T2R 2.4 GHz (QCA9531), with ext. PA and LNA
- 1T1R 5 GHz (QCA9887) with ext. FEM (SKY85710-11)
- 3x U.FL
- 1x USB 2.0
The dedicated development board includes 5 FE ports, USB 2.0 port, two
buttons (one directly connected to SOC reset input), header with all
GPIOs and several LEDs.
Flash instruction:
Vendor firmware is based on OpenWrt. LuCI or sysupgrade can be used to
flash OpenWrt firmware.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
- combine support for Oolite/MiniBox V1.0 in single mach-*.c file
- fix model/board names
- include correct/full vendor name
- drop redundant package and factory image
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
This adds support for AR9331 based Hak5 penetration testing tools:
- WiFi Pineapple NANO
- LAN Turtle
- Packet Squirrel
WiFi Pineapple NANO specifications:
- SoC: Atheros AR9331 (400 MHz)
- RAM: 64 MB (DDR2)
- FLASH: 16 MB
- WiFi: 1T1R AR9331 (built-in), 1T1R AR9271 (built-in via USB bus)
- Ethernet: 1x FE over USB (ASIX AX88772A)
- Ports: 2x RP-SMA for antennas, 1x USB 2.0 (host), 1x micro SD
- Power: USB 5 V, 1.5 A
- Other: status LED, reset button
LAN Turtle specifications:
- SoC: Atheros AR9331 (400 MHz)
- RAM: 64 MB (DDR2)
- FLASH: 16 MB
- WiFi: none
- Ethernet: 1x FE (AR9331), 1x FE over USB (Realtek RTL8152B)
- Ports: 1x RJ45, version dependent: micro SD or 3G SIM slot
- Power: USB 5 V, 0.5 A
- Other: status LED, reset button (inside, on PCB)
Packet Squirrel specifications:
- SoC: Atheros AR9331 (400 MHz)
- RAM: 64 MB (DDR2)
- FLASH: 16 MB
- WiFi: none
- Ethernet: 2x FE (AR9331)
- Ports: 2x RJ45, 1x USB 2.0
- Power: USB 5 V, 0.12 A
- Other: status LED, reset button, 4-way switch
Flash instructions for all 3 devices:
Original firmware is based on OpenWrt.
Use sysupgrade via SSH to flash.
Signed-off-by: Sebastian Kinne <contact@sebkinne.com>
[squashed commits, combined and reworked mach files, aligned board
naming with general convention, fixed minor issues, tested on real
hardware, reworded commit subject and description]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
YunCore T830 is a simple N300 router with 5-port FE switch, detachable
antennas and USB 2.0 port.
Specification:
- 650/597/216 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 5x 10/100 Mbps Ethernet
- 2T2R 2.4 GHz (QCA9531), with ext. PA (SKY65174-21) and LNA
- two external, detachable antennas (RP-SMA)
- 1x USB 2.0
- 8x LED (7 driven by GPIO)
- 1x button (reset)
- DC jack for main power input (12 V)
- UART and JTAG headers on PCB
Flash instruction:
1. First, gain root access to the device, following below steps:
- Login into web gui (default password/IP: admin/192.168.188.253).
- Go to "Advanced" -> "Management" -> "System" and download backup of
configuration (bakfile.bin).
- Open the file as tar.gz archive, edit/update "shadow" file and change
hash of root password to something known.
- Repack the archive, rename it back to "bakfile.bin" and use to
restore configuration of the device.
- After that, device will reboot and can be accessed over SSH.
2. Then, install OpenWrt:
- Login over SSH and issue command:
fw_setenv bootcmd "bootm 0x9f050000 || bootm 0x9fe80000"
- Upload "sysupgrade" image and install it (only if previous command
succeeded) with command: "sysupgrade -n -F openwrt-...".
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Samsung WAM250 is a dual-band (selectable, not simultaneous) wireless
hub, dedicated for Samsung Shape Wireless Audio System. The device is
based on Atheros AR9344. FCC ID: A3LWAM250.
Specification:
- 560/450/225 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 2x 10/100 Mbps Ethernet
- 2T2R 2.4/5 GHz (AR9344), with ext. PA (SE2598L, SE5003L) and LNA
- 1x USB 2.0
- 4x LED (all are driven by GPIO)
- 2x button (reset, wps/speaker add)
- DC jack for main power input (14 V)
- UART header on PCB (J4, RX: 3, TX: 5)
Flash instruction:
This device uses dual-image (switched between upgrades) with a common
jffs2 config partition. Fortunately, there is a way to disable this mode
so that more flash space can be used by OpenWrt image.
You can easily access this device over telnet, using root/root
credentials (the same also work for serial console access).
1. Make sure that your device uses second (bootpart=2) image using
command: "fw_printenv bootpart".
2. If your device uses first image (bootpart=1), perform upgrade to the
latest vendor firmware (after the update, device should boot from
second partition) using web gui (default login: admin/1234567890).
3. Rename "sysupgrade" image to "firmware.bin", download it (you can use
wget, tftp or ftpget) to "/tmp" and issue below commands:
mtd_debug erase /dev/mtd3 0 $(wc -c /tmp/firmware.bin | awk -F' ' '{print $1}')
mtd_debug write /dev/mtd3 0 $(wc -c /tmp/firmware.bin)
fw_setenv bootpart
fw_setenv bootcmd "bootm 0x9f070000"
reboot
Revert to vendor firmware instruction:
1. Download vendor firmware to "/tmp" device and issue below commands:
fw_setenv bootpart 1
sysupgrade -n -F SS_BHUB_v2.2.05.bin
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
COMFAST CF-E385AC is an AC2200 ceiling mount AP with PoE support, based
on Qualcomm/Atheros QCA9558 + QCA9984 + QCA8337N.
Specification:
- 720/600/200 MHz (CPU/DDR/AHB)
- 256 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 2x 10/100/1000 Mbps Ethernet, with PoE support
- 3T3R 2.4 GHz (QCA9558), with external LNA and PA (SE2576L)
- 4T4R 5 GHz (QCA9984), with external FEM (SKY85728-11)
- 7x internal antennas
- 1x RGB LED (driven by GPIO)
- 1x button (reset)
- UART, LEDs/GPIO and USB headers on PCB
- external watchdog (Pericon Technology PT7A7514)
Flash instruction:
Original firmware is based on OpenWrt.
Use sysupgrade image directly in vendor GUI.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
There are now supported two versions of the CF-E355AC board which differ
in 802.11ac radio chip. Include version number in board, model, image
filename, etc., also for the v1.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
COMFAST CF-E355AC v2 is a ceiling mount AP with PoE support, based on
Qualcomm/Atheros QCA9531 + QCA9886.
Short specification:
- 2x 10/100 Mbps Ethernet, with PoE support
- 128MB of RAM (DDR2)
- 16 MB of FLASH
- 2T2R 2.4 GHz, 802.11b/g/n
- 2T2R 5 GHz, 802.11ac/n/a, WAVE 2
- built-in 4x 3 dBi antennas
- output power (max): 500 mW (27 dBm)
- 1x RGB LED, 1x button
- built-in watchdog chipset
Flash instruction:
Original firmware is based on OpenWrt.
Use sysupgrade image directly in vendor GUI.
Signed-off-by: Ding Tengfei <dtf@comfast.cn>
[updated kernel config for both boards]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
WHQX E1700AC v2 is based on Qualcomm QCA9563 + QCA9880 + QCA8334.
Specification:
- 750/400/250 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 8/16 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz (QCA9563) with external FEM (SKY85309-11)
- 3T3R 5 GHz (QCA9880) with external FEM (SKY85728-11)
- 2x 10/100/1000 Mbps Ethernet (one port with PoE support)
- 1x miniPCIe slot (USB 2.0 bus only)
- 1x microSIM slot
- 1x USB 2.0
- 5x LED (4 driven by GPIO)
- 1x button (reset)
- 1x 2-pos switch
- 1x DC jack for main power input (9-48 V)
- UART (J5) and LEDs (J13) headers on PCB
WHQX E600G is based on Qualcomm QCA9531.
Specification:
- 650/391/216 MHz (CPU/DDR/AHB)
- 64/128 MB of RAM (DDR2)
- 8/16 MB of FLASH (SPI NOR)
- 2T2R 2.4 GHz (QCA9531) with external PA (LXK-6601)
- 2x 10/100 Mbps Ethernet (one port with PoE support)
- 1x miniPCIe slot (with PCIe and USB 2.0 buses)
- 1x microSIM slot
- 5x LED (4 driven by GPIO)
- 1x button (reset)
- 1x DC jack for main power input (9-48 V)
- UART (J100), SIM (J34), JTAG (J5) and LEDs (J7) headers on PCB
WHQX E600GAC is based on Qualcomm QCA9531 + QCA9887.
Specification:
- 650/391/216 MHz (CPU/DDR/AHB)
- 64/128 MB of RAM (DDR2)
- 8/16 MB of FLASH (SPI NOR)
- 2T2R 2.4 GHz (QCA9531)
- 1T1R 5 GHz (QCA9887) with external FEM (SKY85703-11)
- 2x 10/100 Mbps Ethernet
- 6x LED (1x RGB, 5 driven by GPIO)
- 1x button (reset)
- 1x DC jack for main power input (9-12 V)
- UART (J100), USB (J102), JTAG (J5) and LEDs (J7) header on PCB
Important notice:
First version of these boards are using different mtd layout, with ART
data at the end. You should not use v2 images on v1 board because it
will result in lost of ART data!
Flash instruction (using U-Boot CLI and tftp server):
1. Configure PC with static IP 192.168.1.10 and tftp server.
2. Rename "sysupgrade" filename to "firmware.bin" and place it in tftp
server directory.
3. Connect PC with one of RJ45 ports, power up the board and press
"enter" key to access U-Boot CLI.
4. Use the following command to update the device to OpenWrt: "run lfw".
Flash instruction (using U-Boot web-based recovery):
1. Configure PC with static IP 192.168.1.xxx(2-254)/24.
2. Connect PC with one of RJ45 ports, press the reset button, power up
the board and keep button pressed for around 6-7 seconds, until LEDs
start flashing.
3. Open your browser and enter 192.168.1.1, select "sysupgrade" image
and click the upgrade button.
Signed-off-by: Peng Zhang <sd20@qxwlan.com>
[reworked: image generation code, mach-* files, commit description,
fixed minor code style issues, rebased on master]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Calling nand_do_upgrade() from platform_pre_upgrade() was deprecated
with 30f61a34b4 ("base-files: always use staged sysupgrade").
Update the platform upgrade code to use platform_do_upgrade() for NAND
images as well.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The watchdog kill command was meant for busybox watchdog. Busybox watchdog
was replaced by the procd watchdog mid 2013 with commit df7ce9301a
("busybox: disable the watchdog utility by default"), which makes the kill
command obsolete since quite some time.
Signed-off-by: Mathias Kresin <dev@kresin.me>
EG-200 is a DIN rail mountable device with one ethernet port, wifi,
an RS-485 port, and an internal USB attached uSD card reader.
Two leds, "modbus" and "etactica" are managed by userspace applications
in factory firmware.
Flash instruction:
Original firmware is based on OpenWrt.
Use sysupgrade image directly in vendor GUI.
Signed-off-by: Karl Palsson <karlp@etactica.com>
This device is identical as TP-Link RE450
RE355 is a dual-band AC1200 router, based on Qualcomm/Atheros
QCA9558+QCA9880.
Specification:
720/600/200 MHz (CPU/DDR/AHB)
64/128 MB of RAM (DDR2)
8 MB of FLASH (SPI NOR)
3T3R 2.4 GHz
3T3R 5 GHz
1x 10/100/1000 Mbps Ethernet
7x LED, 3x button
UART header on PCB
Flash instruction:
Web:
Download lede-ar71xx-generic-archer-c60-v2-squashfs-factory.bin
and use OEM System Tools - Firmware Upgrade site.
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
COMFAST CF-E375AC is a ceiling mount AP with PoE support, based on
Qualcomm/Atheros QCA9563 + QCA9886 + QCA8337.
Short specification:
2x 10/100/1000 Mbps Ethernet, with PoE support
128MB of RAM (DDR2)
16 MB of FLASH
3T3R 2.4 GHz, 802.11b/g/n
2T2R 5 GHz, 802.11ac/n/a, wave 2
built-in 5x 3 dBi antennas
output power (max): 500 mW (27 dBm)
1x RGB LED, 1x button
built-in watchdog chipset
Flash instruction:
Original firmware is based on OpenWrt.
Use sysupgrade image directly in vendor GUI.
Signed-off-by: Ding Tengfei <dtf@comfast.cn>
Add the Embedded Wireless "Balin" platform
SoC: QCA AR9344 or AR9350
RAM: DDR2-RAM 64MBytes
Flash: SPI-NOR 16MBytes
WLAN: 2 x 2 MIMO 2.4 & 5 GHz IEEE802.11 a/b/g/n
Ethernet: 3 x 10/100 Mb/s
USB: 1 x USB2.0 Host/Device bootstrap-pin at power-up
PCI-Express: 1 x lane PCIe 1.2
UART: 1 x Normal, 1 x High-Speed
JTAG: 1 x EJTAG
GPIO: 10 x Input/Output multiplexed
The module comes already with the current vanilla OpenWrt firmware.
To update, use "sysupgrade" image directly in vendor firmware.
Signed-off-by: Catrinel Catrinescu <cc@80211.de>
Tomasz Maciej Nowak
Rafał Miłecki
Koen Vandeputte
Petr Štetiar
Robert Marko
Xavier Douville
Pau Escrich
Sven Eckelmann
Andrew Cameron
Keith Maika
张鹏
Thibaut VARÈNE
Adrian Schmutzler
Arvid E. Picciani
David Ehrmann
David Bauer
Luo chongjun
Chuanhong Guo
Simon Paterson
Matthias Schiffer
Henryk Heisig
Nicolò Veronese
Arne Zachlod
Piotr Dymacz
Sebastian Kinne
Ding Tengfei
Mathias Kresin
Karl Palsson
Catrinel Catrinescu