The firware md5sum check never worked due to missing dollar signs.
Also suppress
`md5sum: can't open '/lib/firmware/ath10k/QCA988X/hw2.0/firmware-3.bin'`
error on any board not using ath10k.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 44486
I got work with this patch.
Ethernet switch (includes VLAN), WiFi connected via PCIe, LEDs, buttons.
In mtd partion map of DTS file, I renamed Linux firmware regions (kernel + root squashfs) to “firmware”because it allows kernel to split kernel and roots and rootfsdata.
signed-off-by: ngc@ff.iij4u.or.jp
——
——
SVN-Revision: 44470
To choose whether bulid or not RT288x PCIe bus driver, CONFIG_SOC_RT2880 is wrong.
Here is its fix, and enables PCIe bus driver for some targets which have 2nd WiFi chipset via PCIe bus.
signed-off-by: ngc@ff.iij4u.or.jp
————
————
SVN-Revision: 44469
- according to imx6 Makefile and u-Boot documentation is itb
and probably should not be changed
- this fixes build error if CONFIG_TARGET_ROOTFS_INCLUDE_FIT is set
(missing .itb file)
- use DTS_DIR (like in imx6 Makefile)
only compile tested
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
Acked-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 44468
This patch adds SDIO support for the brcmfmac driver.
For now only very few boards need it.
Signed off by: José Vázquez Fernández <ppvazquezfer@gmail.com>
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 44465
Kernel commit 1bb5a356c3ea ("net: reduce USB network driver config
options.") hid the USB network drivers behind the new config symbol
CONFIG_USB_NET_DRIVERS.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
SVN-Revision: 44460
The current pxa3xx_nand driver doesn't support sub-page writing,
so the VID header offset must be specified explicitly.
Signed-off-by: Claudio Leite <leitec@staticky.com>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 44455
Git internals are referenced by .git which isn't necessarily a
directory. It may also be a file that references the actual .git
directory using the gitdir directive.
If .git is assumed to be a directory the build will not be able to get
the correct version when openwrt is included as a git submodule because
when used as a submodule .git will actually be a file referencing to a
subdirectory in the parent's git dir.
When the correct version is not detected some image generation tools
will fail because the OpenWrt string will be 'OpenWrtunknown' which is
too long for some header formats.
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
SVN-Revision: 44452
Some Lantiq SoCs are not able to use buffered writes properly with
Intel command set flash due to the way NOR addresses on EBU are
manipulated. This patch disables buffered writes on those devices.
The only device affected at the moment is ARV4510PW, others use
AMD/Fujitsu command set.
Signed-off-by: Matti Laakso <malaakso@elisanet.fi>
SVN-Revision: 44451
For targets with NO_XIP ltq_mtd->map[i].phys equals -1 and devm_ioremap fails.
Fix this by using pdev->resource[i].start instead.
Signed-off-by: Matti Laakso <malaakso@elisanet.fi>
SVN-Revision: 44450
procd gets last console from cmdline, so swapping tty1 (framebuffer) and ttyAMA0 (uart) is enough to force procd output via uart
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 44448
configure tries to guess pagesize by calling getconf, provided by eglibc and compiled for the target, not the host.
Signed-off-by: Nicolas Thill <nico@openwrt.org>
SVN-Revision: 44445
This change adds the configuration options "bssid_whitelist" and
"bssid_blacklist" used to limit the AP selection of a network to a
specified (finite) set or discard certain APs.
This can be useful for environments where multiple networks operate
using the same SSID and roaming between those is not desired. It is also
useful to ignore a faulty or otherwise unwanted AP.
In many applications it is useful not just to enumerate a group of well
known access points, but to use a address/mask notation to match an
entire set of addresses (ca:ff:ee:00:00:00/ff:ff:ff:00:00:00).
This is especially useful if an OpenWrt device with two radios is used to
retransmit the same network (one in AP mode for other clients, one as STA for
the uplink); the following configuration prevents the device from associating
with itself, given that the own AP to be avoided is using the bssid
'C0:FF:EE:D0:0D:42':
config wifi-iface
option device 'radio2'
option network 'uplink'
option mode 'sta'
option ssid 'MyNetwork'
option encryption 'none'
list bssid_blacklist 'C0:FF:EE:D0:0D:42/00:FF:FF:FF:FF:FF'
This change consists of the following cherry-picked upstream commits:
b3d6a0a8259002448a29f14855d58fe0a624ab76
b83e455451a875ba233b3b8ac29aff8b62f064f2
79cd993a623e101952b81fa6a29c674cd858504f
(squashed to implement bssid_{white,black}lists)
0047306bc9ab7d46e8cc22ff9a3e876c47626473
(Add os_snprintf_error() helper)
Signed-off-by: Stefan Tomanek <stefan.tomanek+openwrt@wertarbyte.de>
SVN-Revision: 44438
- kexec-tools is now distributed with tarballs of .tar.gz and .tar.xz
format; .tar.bz2 are not provided anymore.
- Add CONFIG_KEXEC_LZMA for selecting lzma support.
Patches are updated along to:
- Remove the now unnecessary patch 0004-mips_regdefs.patch.
- Drop 100-reduce_size.patch because the size reduction is marginal.
- Allow zlib and lzma support coexist together. This patch has been
merged into upstream project.
- Fix kexec-tools' configure.ac.
- Fix a few compilation warnings.
Size comparison of stripped binaries of kexec malta target with both
zlib and lzma support enabled.
- Before: 41447
- After: 42583
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
SVN-Revision: 44437
John Crispin
Felix Fietkau
Jo-Philipp Wich
Steven Barth
Rafał Miłecki
Imre Kaloz
Nicolas Thill