Changes the platform to use the Chipidea driver instead of the
generic USB host driver which has support for both host and
device modes (selected on boot).
The changes in 930-chipidea-pullup.patch are already in mainline.
I'll upstream 920-usb-chipidea-AR933x-platform-support.patch once I
can test the changes with a newer kernel.
Signed-off-by: Svetoslav Neykov <svetoslav@neykov.name>
erlite mtdparts exposes boot0, boot1 and eeprom regions
as read/write.
this patch adds readonly flags, so these regions can't be
modified. same as it is already for ER profile.
Signed-off-by: Jiri Kastner <cz172638@gmail.com>
Only consider the repository origin url as valid base feed entry if it is a
git://, http:// or https:// location.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Disabling ethernet during reboot (only to enable it again when the
ethernet driver attaches) can put the chip into a faulty state where it
corrupts the header of all incoming packets.
This happens if packets arrive during the time window where the core is
disabled, and it can be easily reproduced by rebooting while sending a
flood ping to the broadcast address.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Since the MIPS IRQ stack patches, lantiq devices were emitting a storm
of messages like this:
[ 567.872172] Spurious IRQ: CAUSE=0x1100c300
Fix this by reworking the IRQ dispatch code
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Commit 131db36 "build: remove separate /install step for host builds" dropped
the package/*/host/install targets in favor to performing the install steps
within the compile target instead.
Adjust package/Makefile accordingly in order to prevent a missing
staging_dir/host/bin/opkg when staging package archives into the rootfs.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This is used to save space on buildbot instances.
If any part of a package needs to be rebuild, the whole package is
rebuilt from scratch. Stamp files are preserved to allow dependency
checks to work
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This makes the build slightly more efficient by avoiding the need to
re-stage packages on every full build run.
It is also necessary for the upcoming CONFIG_AUTOREMOVE feature
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This makes the build slightly more efficient by avoiding the need to
re-stage packages on every full build run.
It is also necessary for the upcoming CONFIG_AUTOREMOVE feature
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The make target does not rewrite the file if the contents didn't
change. This causes make to always consider the target old.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Before SUBDIR was set to $(PATCHVER) which may
or may not include the minor version number of
the linux kernel version. Usually it doesn't.
So the git-clone'd linux kernel was packed without
the minor version number taken into account, which
broke further processing, as it expected the
extracted dir being named linux-$(LINUX_VERSION)
(=with minor version) rather than linux-$(PATCHVER)
(=without minor version).
Changing SUBDIR to $(LINUX_VERSION) creates
consistent behaviour here.
Signed-off-by: Mirko Vogt <mirko-openwrt@nanl.de>
Using a single host package staging dir (and build dir) significantly speeds up
builds when multiple targets are built in succession, especially for large host
packages like NodeJS.
$(STAGING_DIR)/host is kept in addition to $(STAGING_DIR_HOSTPKG) in most
places; it is still used as destination for host files in Build/InstallDev.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
This patch adds support for the Netgear WN3000RPv3
http://www.netgear.com/support/product/wn3000rpv3.aspx
Specifications:
- SoC: MediaTek MT7620A (580MHz, ramips)
- RAM: 32MB DDR
- Storage: 8MB NOR SPI flash
- Wireless: builtin MT7620A, 2x2:2 with u.FL connectors
- Ethernet: 1x100M
- Serial: JP1 header, 57600-8N1
- Stock firmware based on OpenWRT Kamikaze
Like the EX2700, the bootloader expects a secondary image signature,
see https://forum.openwrt.org/viewtopic.php?pid=312577#p312577
This is why the same fakeroot image is used for the WN3000
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
The soft_config partition must be writeable for rbcfg to be able to
enact changes to the routerboot configuration.
The read-only flag was a mistake in the initial patch. Removing it
brings mach-rb941.c in line with all other RB platforms.
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
D7800 has a simular hardware to R7800 and uses dual QCA9980 for both 2.4GHz and 5GHz band.
However there is no proper initialization for them, which causes a kernel panic due to failed firmware loading.
This patch adds d7800 to ath10k caldata extraction list.
I can get two functional wireless bands after making change to it.
Signed-off-by: Zhang Jingye <934526987@qq.com>
For the miwifi-mini, the offset of ethernet mac should be 0x28
which you can easyily dump from 'Factory' partition.
Signed-off-by: BangLang Huang <banglang.huang@foxmail.com>
Admittedly, this is my own OCD wanting to get rid of this.
Because I tried (a while back to upgrade QEMU to a newer version),
and (during that attempt) I tried to get rid of this.
Tested on Linux & Mac.
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Do not strip static libraries shipped with the SDK in order to preserve the
archive index. If we strip the index of the shipped libraries, host programs
will fail to link these libraries with errors like:
libssl.a: error adding symbols: Archive has no index; run ranlib to add one
The error was found while investigating a Python host build failure within
the SDK environment.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The final semantic is the same, but this is a bit more correct.
Build tested on Windows 10 (yes, there is some
Ubuntu mode for Windows 10, and I've been also building LEDE
on it for a few weeks).
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
This change adds the sp5100_tco driver as a kernel module for the x86
target. Specifically, this can be used by the PCEngines APU2/APU3. The
reason for having this as a kernel module is to allow users to
load/unload it on demand, as the I2C interface on the APU2/APU3 will not
work while this module is loaded. More info can be found on GitHub at
https://github.com/riptidewave93/LEDE-APU2/pull/5#issuecomment-255667736
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
This adds the following patches to the x86 target:
sp5100_tco: Add AMD Mullins platform support
sp5100_tco: Add AMD Carrizo platform support
sp5100_tco: fix the device check for SB800 and later chipsets
watchdog: sp5100_tco: properly check for new register layouts
With these added, the sp5100_tco driver can then be used on newer AMD
platforms, such as the PCEngines APU2/APU3 boards.
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
Mikrotik RB411U has only one ethernet port - eth0. This patch allows to create
correct config with one lan section.
Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl>
Add full support for Mikrotik RB-941-2nD (hAP lite)
Original patch by Sergey Sergeev <adron@yapic.net> and
more information is available here:
https://wiki.openwrt.org/toh/mikrotik/rb941_2nd
I updated and adapted the patch to apply cleanly to LEDE trunk
and added proper numbering for the switch ports (matching case
labels).
Tested working on actual hardware with the information
provided in the above webpage. Sysupgrade works.
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove the wget2nand script, drop the need for manual installation,
use sysupgrade instead.
There are now two different NAND images, one for 64 MiB flashes, the
other for >= 128 MiB
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Vitaly Chekryzhev
Svetoslav Neykov
Jiri Kastner
Jo-Philipp Wich
Felix Fietkau
Matthias Schiffer
Mirko Vogt
Hans Dedecker
Thibaut VARENE
Zhang Jingye
BangLang Huang
Alexandru Ardelean
Joseph C. Lehner
Rosen Penev
Rafał Miłecki
Chris Blake
Cezary Jackiewicz