ath79: add support for AVM FRITZ!WLAN Repeater 1750E
This commit adds support for the AVM Fritz!WLAN Repeater 1750E SOC: Qualcomm QCA9556 (Scorpion) 720MHz MIPS74Kc RAM: 64MB Zentel A3R12E40CBF DDR2 FLASH: 16MiB Winbond W25Q128 SPI NOR WLAN1: QCA9556 2.4 GHz 802.11b/g/n 3x3 WLAN2: QCA9880 5 GHz 802.11 n/ac 3x3 INPUT: WPS button LED: Power, WiFi, LAN, RSSI indicator Serial: Header Next to Black metal shield Pinout is 3.3V - RX - TX - GND (Square Pad is 3.3V) The Serial setting is 115200-8-N-1. Tested and working: - Ethernet - 2.4 GHz WiFi (correct MAC) - 5 GHz WiFi (correct MAC) - Installation via EVA bootloader - OpenWRT sysupgrade - Buttons - LEDs Installation via EVA: In the first seconds after Power is connected, the bootloader will listen for FTP connections on 192.168.178.1. Firmware can be uploaded like following: ftp> quote USER adam2 ftp> quote PASS adam2 ftp> binary ftp> debug ftp> passive ftp> quote MEDIA FLSH ftp> put openwrt-sysupgrade.bin mtd1 Note that this procedure might take up to two minutes. You need to powercycle the Device afterwards to boot OpenWRT. Signed-off-by: David Bauer <mail@david-bauer.net>master
parent
d883eaacd4
commit
8918c038f3
@ -0,0 +1,195 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
/dts-v1/;
|
||||
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
|
||||
#include "qca9557.dtsi"
|
||||
|
||||
/ {
|
||||
compatible = "avm,fritz1750e", "qca,qca9557";
|
||||
model = "AVM FRITZ!WLAN Repeater 1750E";
|
||||
|
||||
chosen {
|
||||
bootargs = "console=ttyS0,115200n8";
|
||||
};
|
||||
|
||||
aliases {
|
||||
led-boot = &led_power;
|
||||
led-failsafe = &led_power;
|
||||
led-running = &led_power;
|
||||
led-upgrade = &led_power;
|
||||
};
|
||||
|
||||
led_spi {
|
||||
compatible = "spi-gpio";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
sck-gpios = <&gpio 14 GPIO_ACTIVE_HIGH>;
|
||||
mosi-gpios = <&gpio 15 GPIO_ACTIVE_HIGH>;
|
||||
num-chipselects = <0>;
|
||||
|
||||
spi_gpio: led_gpio@0 {
|
||||
compatible = "fairchild,74hc595";
|
||||
reg = <0>;
|
||||
gpio-controller;
|
||||
#gpio-cells = <2>;
|
||||
registers-number = <1>;
|
||||
spi-max-frequency = <10000000>;
|
||||
|
||||
gpio_latch_bit {
|
||||
gpio-hog;
|
||||
gpios = <7 GPIO_ACTIVE_HIGH>;
|
||||
output-high;
|
||||
line-name = "gpio-latch-bit";
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
led_power: power {
|
||||
label = "fritz1750e:green:power";
|
||||
gpios = <&spi_gpio 6 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
wlan {
|
||||
label = "fritz1750e:green:wlan";
|
||||
gpios = <&spi_gpio 5 GPIO_ACTIVE_HIGH>;
|
||||
linux,default-trigger = "phy1tpt";
|
||||
};
|
||||
|
||||
lan {
|
||||
label = "fritz1750e:green:lan";
|
||||
gpios = <&gpio 13 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
rssi0 {
|
||||
label = "fritz1750e:green:rssi0";
|
||||
gpios = <&spi_gpio 0 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
rssi1 {
|
||||
label = "fritz1750e:green:rssi1";
|
||||
gpios = <&spi_gpio 1 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
rssi2 {
|
||||
label = "fritz1750e:green:rssi2";
|
||||
gpios = <&spi_gpio 2 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
rssi3 {
|
||||
label = "fritz1750e:green:rssi3";
|
||||
gpios = <&spi_gpio 3 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
rssi4 {
|
||||
label = "fritz1750e:green:rssi4";
|
||||
gpios = <&spi_gpio 4 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
};
|
||||
|
||||
keys {
|
||||
compatible = "gpio-keys";
|
||||
|
||||
wps {
|
||||
label = "wps";
|
||||
linux,code = <KEY_WPS_BUTTON>;
|
||||
gpios = <&gpio 4 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&pcie0 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&uart {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&spi {
|
||||
status = "okay";
|
||||
num-cs = <1>;
|
||||
|
||||
flash@0 {
|
||||
compatible = "jedec,spi-nor";
|
||||
reg = <0>;
|
||||
spi-max-frequency = <25000000>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "urlader";
|
||||
reg = <0x0 0x20000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@20000 {
|
||||
compatible = "avm,eva-firmware";
|
||||
label = "firmware";
|
||||
reg = <0x20000 0xee0000>;
|
||||
};
|
||||
|
||||
partition@f00000 {
|
||||
label = "tffs (1)";
|
||||
reg = <0xf00000 0x80000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@f80000 {
|
||||
label = "tffs (2)";
|
||||
reg = <0xf80000 0x80000>;
|
||||
read-only;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&gpio {
|
||||
reset-pcie-ep {
|
||||
gpio-hog;
|
||||
gpios = <17 GPIO_ACTIVE_HIGH>;
|
||||
output-high;
|
||||
line-name = "PCIE EP reset";
|
||||
};
|
||||
|
||||
reset-pcie {
|
||||
gpio-hog;
|
||||
gpios = <18 GPIO_ACTIVE_HIGH>;
|
||||
output-high;
|
||||
line-name = "PCIE Bus reset";
|
||||
};
|
||||
};
|
||||
|
||||
&wmac {
|
||||
status = "okay";
|
||||
qca,no-eeprom;
|
||||
};
|
||||
|
||||
ð1 {
|
||||
status = "okay";
|
||||
|
||||
phy-handle = <&phy0>;
|
||||
pll-data = <0x3000000 0x101 0x1313>;
|
||||
|
||||
gmac-config {
|
||||
device = <&gmac>;
|
||||
ge0-sgmii = <0>;
|
||||
};
|
||||
};
|
||||
|
||||
&mdio1 {
|
||||
status = "okay";
|
||||
|
||||
phy0: ethernet-phy@0 {
|
||||
reg = <0>;
|
||||
reset-gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
};
|
Loading…
Reference in New Issue