|
|
|
|
#!/bin/sh
|
|
|
|
|
|
|
|
|
|
. /lib/functions/system.sh
|
|
|
|
|
. /lib/functions/uci-defaults.sh
|
|
|
|
|
|
|
|
|
|
ath79_setup_interfaces()
|
|
|
|
|
{
|
|
|
|
|
local board="$1"
|
|
|
|
|
|
|
|
|
|
case "$board" in
|
|
|
|
|
aerohive,hiveap-121)
|
|
|
|
|
ucidef_set_interface_lan "eth0"
|
|
|
|
|
;;
|
ath79: add support for Netgear WNDR4300
This patch adds ath79 support for Netgear WNDR4300.
Router was previously supported by ar71xx target only.
Note: device requires 'ar934x-nand' driver in kernel.
Specification
=============
* Description: Netgear WNDR4300
* Loader: U-boot
* SOC: Atheros AR9344 (560 MHz)
* RAM: 128 MiB
* Flash: 128 MiB (NAND)
- U-boot binary: 256 KiB
- U-boot environment: 256 KiB
- ART: 256 KiB
- POT: 512 KiB
- Language: 2 MiB
- Config: 512 KiB
- Traffic Meter: 3 MiB
- Firmware: 25 MiB
- ART Backup: 256 KiB
- Reserved: 96 MiB
* Ethernet: 5 x 10/100/1000 (4 x LAN, 1 x WAN) (AR8327)
* Wireless:
- 2.4 GHz b/g/n (internal)
- 5 GHz a/n (AR9580)
* USB: yes, 1 x USB 2.0
* Buttons:
- Reset
- WiFi (rfkill)
- WPS
* LEDs:
- Power (amber/green)
- WAN (amber/green)
- WLAN 2G (green)
- WLAN 5G (blue)
- 4 x LAN (amber/green)
- USB (green)
- WPS (amber/green)
* UART: 4-pin connector JP1, 3.3V (Vcc, TX, RX, GND), 115200 8N1
* Power supply: DC 12V 2.5A
* MAC addresses: LAN=WLAN2G on case label, WAN +1, WLAN5G +2
Installation
============
* TFTP recovery
* TFTP via U-boot prompt
* sysupgrade
* Web interface
Note about partitioning: firmware partition offset (0x6c0000) is
hardcoded into vendor's u-boot, so this partition cannot be moved
and resized to include Netgear-specific flash areas (pot, language,
config, traffic_meter) not used by OpenWrt.
Test build configuration
========================
CONFIG_TARGET_ath79=y
CONFIG_TARGET_ath79_nand=y
CONFIG_TARGET_ath79_nand_DEVICE_netgear_wndr4300=y
CONFIG_ALL_KMODS=y
CONFIG_DEVEL=y
CONFIG_CCACHE=y
CONFIG_COLLECT_KERNEL_DEBUG=y
CONFIG_IMAGEOPT=y
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
5 years ago
|
|
|
netgear,wndr4300)
|
|
|
|
|
ucidef_add_switch "switch0" \
|
|
|
|
|
"0@eth0" "1:lan:4" "2:lan:3" "3:lan:2" "4:lan:1" "5:wan"
|
|
|
|
|
;;
|
|
|
|
|
zyxel,nbg6716)
|
|
|
|
|
ucidef_add_switch "switch0" \
|
|
|
|
|
"0@eth0" "1:lan" "2:lan" "3:lan" "4:lan" "5:wan" "6@eth1"
|
|
|
|
|
;;
|
|
|
|
|
*)
|
|
|
|
|
ucidef_set_interfaces_lan_wan "eth0" "eth1"
|
|
|
|
|
;;
|
|
|
|
|
esac
|
|
|
|
|
}
|
|
|
|
|
|
|
|
|
|
ath79_setup_macs()
|
|
|
|
|
{
|
|
|
|
|
local board="$1"
|
|
|
|
|
|
|
|
|
|
case "$board" in
|
ath79: add support for Netgear WNDR4300
This patch adds ath79 support for Netgear WNDR4300.
Router was previously supported by ar71xx target only.
Note: device requires 'ar934x-nand' driver in kernel.
Specification
=============
* Description: Netgear WNDR4300
* Loader: U-boot
* SOC: Atheros AR9344 (560 MHz)
* RAM: 128 MiB
* Flash: 128 MiB (NAND)
- U-boot binary: 256 KiB
- U-boot environment: 256 KiB
- ART: 256 KiB
- POT: 512 KiB
- Language: 2 MiB
- Config: 512 KiB
- Traffic Meter: 3 MiB
- Firmware: 25 MiB
- ART Backup: 256 KiB
- Reserved: 96 MiB
* Ethernet: 5 x 10/100/1000 (4 x LAN, 1 x WAN) (AR8327)
* Wireless:
- 2.4 GHz b/g/n (internal)
- 5 GHz a/n (AR9580)
* USB: yes, 1 x USB 2.0
* Buttons:
- Reset
- WiFi (rfkill)
- WPS
* LEDs:
- Power (amber/green)
- WAN (amber/green)
- WLAN 2G (green)
- WLAN 5G (blue)
- 4 x LAN (amber/green)
- USB (green)
- WPS (amber/green)
* UART: 4-pin connector JP1, 3.3V (Vcc, TX, RX, GND), 115200 8N1
* Power supply: DC 12V 2.5A
* MAC addresses: LAN=WLAN2G on case label, WAN +1, WLAN5G +2
Installation
============
* TFTP recovery
* TFTP via U-boot prompt
* sysupgrade
* Web interface
Note about partitioning: firmware partition offset (0x6c0000) is
hardcoded into vendor's u-boot, so this partition cannot be moved
and resized to include Netgear-specific flash areas (pot, language,
config, traffic_meter) not used by OpenWrt.
Test build configuration
========================
CONFIG_TARGET_ath79=y
CONFIG_TARGET_ath79_nand=y
CONFIG_TARGET_ath79_nand_DEVICE_netgear_wndr4300=y
CONFIG_ALL_KMODS=y
CONFIG_DEVEL=y
CONFIG_CCACHE=y
CONFIG_COLLECT_KERNEL_DEBUG=y
CONFIG_IMAGEOPT=y
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
5 years ago
|
|
|
netgear,wndr4300)
|
|
|
|
|
wan_mac=$(mtd_get_mac_binary caldata 0x6)
|
|
|
|
|
;;
|
|
|
|
|
zyxel,nbg6716)
|
|
|
|
|
lan_mac=$(macaddr_add $(mtd_get_mac_ascii u-boot-env ethaddr) +2)
|
|
|
|
|
wan_mac=$(macaddr_add $(mtd_get_mac_ascii u-boot-env ethaddr) +3)
|
|
|
|
|
;;
|
|
|
|
|
esac
|
|
|
|
|
|
|
|
|
|
[ -n "$lan_mac" ] && ucidef_set_interface_macaddr "lan" $lan_mac
|
|
|
|
|
[ -n "$wan_mac" ] && ucidef_set_interface_macaddr "wan" $wan_mac
|
|
|
|
|
[ -n "$label_mac" ] && ucidef_set_label_macaddr $label_mac
|
|
|
|
|
}
|
|
|
|
|
|
|
|
|
|
board_config_update
|
|
|
|
|
board=$(board_name)
|
|
|
|
|
ath79_setup_interfaces $board
|
|
|
|
|
ath79_setup_macs $board
|
|
|
|
|
board_config_flush
|
|
|
|
|
|
|
|
|
|
exit 0
|
