You cannot select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
openwrt/target/linux/ipq806x/base-files/etc/board.d/02_network

64 lines
1.6 KiB
Plaintext

#!/bin/sh
#
# Copyright (c) 2015 The Linux Foundation. All rights reserved.
# Copyright (c) 2011-2015 OpenWrt.org
#
. /lib/functions/uci-defaults.sh
. /lib/functions/system.sh
board_config_update
board=$(board_name)
case "$board" in
avm,fritzbox-4040)
ucidef_set_interfaces_lan_wan "eth0" "eth1"
ucidef_add_switch "switch0" \
"0u@eth0" "1:lan" "2:lan" "3:lan" "4:lan"
;;
linksys,ea8500)
hw_mac_addr=$(mtd_get_mac_ascii devinfo hw_mac_addr)
ucidef_add_switch "switch0" \
"0@eth0" "1:lan" "2:lan" "3:lan" "4:lan" "5:wan"
ucidef_set_interface_macaddr "lan" "$hw_mac_addr"
ucidef_set_interface_macaddr "wan" "$hw_mac_addr"
;;
netgear,d7800 |\
netgear,r7500 |\
netgear,r7500v2 |\
netgear,r7800 |\
qcom,ipq8064-ap148 |\
tplink,vr2600v)
ucidef_add_switch "switch0" \
"1:lan" "2:lan" "3:lan" "4:lan" "6@eth1" "5:wan" "0@eth0"
;;
glinet,gl-b1300 |\
openmesh,a42)
ucidef_set_interfaces_lan_wan "eth1" "eth0"
;;
qcom,ipq8064-db149)
ucidef_set_interface_lan "eth1 eth2 eth3"
ucidef_add_switch "switch0" \
"1:lan" "2:lan" "3:lan" "4:lan" "6u@eth1" "5:wan" "0u@eth0"
;;
tplink,c2600)
ipq806x: add ipq4019 fritz4040 support This patch adds support for AVM FRITZ!Box 4040. hardware highlights: SOC: IPQ4018 / QCA Dakota CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7 DRAM: 256 MiB Nanya NT5CC128M16IP FLASH: 32 MiB MXIC MX25L25635FMI ETH: Qualcomm Atheros QCA8075 Gigabit Switch (4 x LAN, 1 x WAN) USB: 1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC) 1 x 2.0 (via Synopsys DesignWare DWC3 controller in the SoC) WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2 WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2 INPUT: one WLAN and one WPS button LEDS: Power, WAN/Internet, WIFI, INFO (red and amber) and LAN. Serial: WARNING: The serial port needs a TTL/RS-232 v3.3 level converter! The Serial setting is 115200-8-N-1. The SoC's serial port is right next to the MXIC FLASH chip. The board has a unpopulated 1x4 0.1" header for it. Use a multimeter to figure out the pinout! This board currently needs an additional u-boot image in order to boot properly. Booting with EVA isn't possible ATM. Install Procedure: 0. It's highly recommended to connect to the serial port. The serial settings are listed above. 1. install a u-boot image for AVM Fritz!Box 4040 (see <https://github.com/chunkeey/FritzBox-4040-UBOOT/releases> and <https://github.com/chunkeey/FritzBox-4040-UBOOT/blob/master/upload-to-f4040.sh>) 2. upload the initramfs.itb image via tftp (u-boot listens to 192.168.1.1 - use binary transfer mode!) 3. connect to the FB4040 and use sysupgrade sysupgrade.bin to install the image. Works: - Switch and Ethernet (99%) - Buttons (WLAN, WPS) - FLASH (1 x 32MiB NOR Chip) - WLAN2G and WLAN5G - CPUFREQ scaling - PRNG - serial - Crypto Accelerator - sysupgrade (Read the flash instructions to avoid bricking) - full LEDE Install (Read the flash instructions to avoid bricking) - LEDs (Power, WAN, Info (red and amber), LAN) The LEDs are connected to the QCA8075 LED ports. The AR40xx driver contains a gpio-controller to handle these special "GPIOs". - USB Both 3.0 and 2.0 ports - many packages from other ARMv7 boards (This does include the RaspberryPi Model 2!) - ... Not planned: - WAN<->LAN short-cut - Qualcomm Secure Execution Environment - ... Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John Crispin <john@phrozen.org>
7 years ago
ucidef_add_switch "switch0" \
"1:lan:4" "2:lan:3" "3:lan:2" "4:lan:1" "6@eth1" "5:wan" "0@eth0"
ipq806x: add ipq4019 fritz4040 support This patch adds support for AVM FRITZ!Box 4040. hardware highlights: SOC: IPQ4018 / QCA Dakota CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7 DRAM: 256 MiB Nanya NT5CC128M16IP FLASH: 32 MiB MXIC MX25L25635FMI ETH: Qualcomm Atheros QCA8075 Gigabit Switch (4 x LAN, 1 x WAN) USB: 1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC) 1 x 2.0 (via Synopsys DesignWare DWC3 controller in the SoC) WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2 WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2 INPUT: one WLAN and one WPS button LEDS: Power, WAN/Internet, WIFI, INFO (red and amber) and LAN. Serial: WARNING: The serial port needs a TTL/RS-232 v3.3 level converter! The Serial setting is 115200-8-N-1. The SoC's serial port is right next to the MXIC FLASH chip. The board has a unpopulated 1x4 0.1" header for it. Use a multimeter to figure out the pinout! This board currently needs an additional u-boot image in order to boot properly. Booting with EVA isn't possible ATM. Install Procedure: 0. It's highly recommended to connect to the serial port. The serial settings are listed above. 1. install a u-boot image for AVM Fritz!Box 4040 (see <https://github.com/chunkeey/FritzBox-4040-UBOOT/releases> and <https://github.com/chunkeey/FritzBox-4040-UBOOT/blob/master/upload-to-f4040.sh>) 2. upload the initramfs.itb image via tftp (u-boot listens to 192.168.1.1 - use binary transfer mode!) 3. connect to the FB4040 and use sysupgrade sysupgrade.bin to install the image. Works: - Switch and Ethernet (99%) - Buttons (WLAN, WPS) - FLASH (1 x 32MiB NOR Chip) - WLAN2G and WLAN5G - CPUFREQ scaling - PRNG - serial - Crypto Accelerator - sysupgrade (Read the flash instructions to avoid bricking) - full LEDE Install (Read the flash instructions to avoid bricking) - LEDs (Power, WAN, Info (red and amber), LAN) The LEDs are connected to the QCA8075 LED ports. The AR40xx driver contains a gpio-controller to handle these special "GPIOs". - USB Both 3.0 and 2.0 ports - many packages from other ARMv7 boards (This does include the RaspberryPi Model 2!) - ... Not planned: - WAN<->LAN short-cut - Qualcomm Secure Execution Environment - ... Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John Crispin <john@phrozen.org>
7 years ago
;;
zyxel,nbg6817)
hw_mac_addr=$(mtd_get_mac_ascii 0:APPSBLENV ethaddr)
ucidef_add_switch "switch0" \
"1:lan" "2:lan" "3:lan" "4:lan" "6@eth1" "5:wan" "0@eth0"
ucidef_set_interface_macaddr "lan" "$(macaddr_add $hw_mac_addr 2)"
ucidef_set_interface_macaddr "wan" "$(macaddr_add $hw_mac_addr 3)"
;;
*)
echo "Unsupported hardware. Network interfaces not intialized"
;;
esac
board_config_flush
exit 0