You cannot select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
201 lines
3.2 KiB
Plaintext
201 lines
3.2 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
|
/dts-v1/;
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/input/input.h>
|
|
|
|
#include "qca955x.dtsi"
|
|
|
|
/ {
|
|
compatible = "librerouter,librerouter-v1", "qca,qca9558";
|
|
model = "LibreRouter v1";
|
|
|
|
aliases {
|
|
led-boot = &led_system;
|
|
led-failsafe = &led_system;
|
|
led-running = &led_system;
|
|
led-upgrade = &led_system;
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
|
|
led_system: system {
|
|
label = "librerouter-v1:green:system";
|
|
gpios = <&gpio 23 GPIO_ACTIVE_HIGH>;
|
|
default-state = "on";
|
|
};
|
|
|
|
wifi_green {
|
|
label = "librerouter-v1:green:wlan2g";
|
|
gpios = <&gpio 22 GPIO_ACTIVE_LOW>;
|
|
linux,default-trigger = "phy0tpt";
|
|
};
|
|
|
|
status_blue {
|
|
label = "librerouter-v1:blue:status";
|
|
gpios = <&gpio 20 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
|
|
keys {
|
|
compatible = "gpio-keys";
|
|
|
|
reset {
|
|
label = "Reset";
|
|
linux,code = <KEY_RESTART>;
|
|
gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
|
|
debounce-interval = <60>;
|
|
};
|
|
};
|
|
|
|
watchdog {
|
|
compatible = "linux,wdt-gpio";
|
|
gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
|
|
hw_algo = "toggle";
|
|
hw_margin_ms = <1000>;
|
|
always-running;
|
|
};
|
|
};
|
|
|
|
&pcie0 {
|
|
status = "okay";
|
|
|
|
wifi@0,0 {
|
|
compatible = "pci168c,0033";
|
|
reg = <0x0000 0 0 0 0>;
|
|
};
|
|
};
|
|
|
|
&pcie1 {
|
|
status = "okay";
|
|
|
|
wifi@0,0 {
|
|
compatible = "pci168c,0033";
|
|
reg = <0x0000 0 0 0 0>;
|
|
};
|
|
};
|
|
|
|
&uart {
|
|
status = "okay";
|
|
};
|
|
|
|
&usb_phy0 {
|
|
status = "okay";
|
|
};
|
|
|
|
&usb0 {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
status = "okay";
|
|
};
|
|
|
|
&usb_phy1 {
|
|
status = "okay";
|
|
};
|
|
|
|
&usb1 {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
status = "okay";
|
|
};
|
|
|
|
&spi {
|
|
status = "okay";
|
|
|
|
num-cs = <1>;
|
|
|
|
flash@0 {
|
|
compatible = "jedec,spi-nor";
|
|
reg = <0>;
|
|
spi-max-frequency = <25000000>;
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
partition@0 {
|
|
label = "u-boot";
|
|
reg = <0x000000 0x040000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@40000 {
|
|
label = "u-boot-env";
|
|
reg = <0x040000 0x010000>;
|
|
};
|
|
|
|
partition@50000 {
|
|
compatible = "denx,uimage";
|
|
label = "firmware";
|
|
reg = <0x050000 0x7c0000>;
|
|
};
|
|
|
|
partition@810000 {
|
|
label = "fw2";
|
|
reg = <0x810000 0x7d0000>;
|
|
};
|
|
|
|
partition@fd0000 {
|
|
label = "res";
|
|
reg = <0xfd0000 0x20000>;
|
|
};
|
|
|
|
art: partition@ff0000 {
|
|
label = "art";
|
|
reg = <0xff0000 0x010000>;
|
|
read-only;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
&mdio0 {
|
|
status = "okay";
|
|
|
|
phy0: ethernet-phy@0 {
|
|
reg = <0>;
|
|
qca,ar8327-initvals = <
|
|
0x04 0x87600000 /* PORT0: RGMII, MAC0/6 exchage, tx_delay 01, rx_delay 10 */
|
|
0x0c 0x00000080 /* PORT6: SGMII */
|
|
0x10 0x81000080 /* POWER_ON_STRAP: LED open drain, SerDes auto-neg disabled */
|
|
0x50 0xcf37cf37 /* LED_CTRL0 */
|
|
0x54 0xcf37cf37 /* LED_CTRL1 */
|
|
0x58 0xcf37cf37 /* LED_CTRL2 */
|
|
0x5c 0x0 /* LED_CTRL3 */
|
|
0x7c 0x0000007e /* PORT0_STATUS */
|
|
0x94 0x0000007e /* PORT6 STATUS */
|
|
>;
|
|
};
|
|
};
|
|
|
|
ð0 {
|
|
status = "okay";
|
|
|
|
pll-data = <0xa6000000 0x00000101 0x00001616>;
|
|
mtd-mac-address = <&art 0x0>;
|
|
|
|
phy-handle = <&phy0>;
|
|
};
|
|
|
|
ð1 {
|
|
status = "okay";
|
|
|
|
phy-mode = "sgmii";
|
|
pll-data = <0x03000101 0x00000101 0x00001616>;
|
|
mtd-mac-address = <&art 0x6>;
|
|
|
|
fixed-link {
|
|
speed = <1000>;
|
|
full-duplex;
|
|
};
|
|
};
|
|
|
|
&wmac {
|
|
status = "okay";
|
|
|
|
mtd-cal-data = <&art 0x1000>;
|
|
mtd-mac-address = <&art 0xc>;
|
|
};
|