You cannot select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
ad84c09502
This patch adds support for the COMFAST CF-E130N v2, an outdoor wireless CPE with a single Ethernet port and a 802.11bgn radio. Specifications: - QCA9531 SoC - 1x 10/100 Mbps Ethernet with PoE-in support - 64 MB of RAM (DDR2) - 16 MB of FLASH - 5 dBi built-in antenna - POWER/LAN/WLAN green LEDs - 4x RSSI LEDs (2x red, 2x green) - UART (115200 8N1) and GPIO (J9) headers on PCB Flashing instructions: The original firmware is based on OpenWrt so a sysupgrade image can be installed via the stock web GUI. The U-boot bootloader also contains a backup TFTP client to upload the firmware from. Upon boot, it checks its ethernet network for the IP 192.168.1.10. Host a TFTP server and provide the image to be flashed as file firmware_auto.bin. MAC address setup: The art partition contains four consecutive MAC addresses: 0x0 aa:bb:cc:xx:xx:c4 0x6 aa:bb:cc:xx:xx:c6 0x1002 aa:bb:cc:xx:xx:c5 0x5006 aa:bb:cc:xx:xx:c7 However, the manufacturer in its infinite wisdom decided that one address is enough and both eth0 and WiFi get the MAC address from 0x0 (yes, that's overwriting the existing and valid address in 0x1002). This is obviously also the address on the device's label. Signed-off-by: Pavel Balan <admin@kryma.net> [fix configs partition, fix IMAGE_SIZE, add MAC address comment, rename ATH_SOC to SOC] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> |
4 years ago | |
|---|---|---|
| .github | 6 years ago | |
| config | 4 years ago | |
| include | 4 years ago | |
| package | 4 years ago | |
| scripts | 4 years ago | |
| target | 4 years ago | |
| toolchain | 4 years ago | |
| tools | 4 years ago | |
| .gitattributes | 12 years ago | |
| .gitignore | 4 years ago | |
| BSDmakefile | 17 years ago | |
| Config.in | 7 years ago | |
| LICENSE | 8 years ago | |
| Makefile | 4 years ago | |
| README | 5 years ago | |
| feeds.conf.default | 6 years ago | |
| rules.mk | 5 years ago | |
README
_______ ________ __
| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -__| || | | || _|| _|
|_______|| __|_____|__|__||________||__| |____|
|__| W I R E L E S S F R E E D O M
-----------------------------------------------------
This is the buildsystem for the OpenWrt Linux distribution.
To build your own firmware you need a Linux, BSD or MacOSX system (case
sensitive filesystem required). Cygwin is unsupported because of the lack
of a case sensitive file system.
You need gcc, binutils, bzip2, flex, python3.5+, perl, make, find, grep, diff,
unzip, gawk, getopt, subversion, libz-dev and libc headers installed.
1. Run "./scripts/feeds update -a" to obtain all the latest package definitions
defined in feeds.conf / feeds.conf.default
2. Run "./scripts/feeds install -a" to install symlinks for all obtained
packages into package/feeds/
3. Run "make menuconfig" to select your preferred configuration for the
toolchain, target system & firmware packages.
4. Run "make" to build your firmware. This will download all sources, build
the cross-compile toolchain and then cross-compile the Linux kernel & all
chosen applications for your target system.
Sunshine!
Your OpenWrt Community
http://www.openwrt.org