You cannot select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
6a950afde1
This adds support for the Ubiquiti Nanostation Loco M (XM), which
has the same board/LEDs as the Bullet M XM, but different case and
antennas.
Specifications:
- AR7241 SoC @ 400 MHz
- 32 MB RAM
- 8 MB SPI flash
- 1x 10/100 Mbps Ethernet, 24 Vdc PoE-in
- NS Loco M2: built-in antenna: 8 dBi; AR9287
- NS Loco M5: built-in antenna: 13 dBi; 2T2R 5 GHz radio
- POWER/LAN green LEDs
- 4x RSSI LEDs (red, orange, green, green)
- UART (115200 8N1) on PCB
Flashing via WebUI:
Upload the factory image via the stock firmware web UI.
Note that only certain firmware versions accept unsigned
images. Refer to the device's Wiki page for further information.
Flashing via TFTP:
Same procedure as other NanoStation M boards.
- Use a pointy tool (e.g., pen cap, paper clip) and keep the reset
button on the device or on the PoE supply pressed
- Power on the device via PoE (keep reset button pressed)
- Keep pressing until LEDs flash alternatively LED1+LED3 =>
LED2+LED4 => LED1+LED3, etc.
- Release reset button
- The device starts a TFTP server at 192.168.1.20
- Set a static IP on the computer (e.g., 192.168.1.21/24)
- Upload via tftp the factory image:
$ tftp 192.168.1.20
tftp> bin
tftp> trace
tftp> put openwrt-ath79-generic-xxxxx-ubnt_nanostation-loco-m-squashfs-factory.bin
Tested on NanoStation Loco M2.
Signed-off-by: Sven Roederer <freifunk@it-solutions.geroedel.de>
Co-developed-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit
|
4 years ago | |
|---|---|---|
| .github | 6 years ago | |
| config | 4 years ago | |
| include | 4 years ago | |
| package | 4 years ago | |
| scripts | 4 years ago | |
| target | 4 years ago | |
| toolchain | 4 years ago | |
| tools | 4 years ago | |
| .gitattributes | 12 years ago | |
| .gitignore | 5 years ago | |
| BSDmakefile | 17 years ago | |
| Config.in | 6 years ago | |
| LICENSE | 8 years ago | |
| Makefile | 5 years ago | |
| README | 6 years ago | |
| feeds.conf.default | 4 years ago | |
| rules.mk | 5 years ago | |
README
_______ ________ __
| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -__| || | | || _|| _|
|_______|| __|_____|__|__||________||__| |____|
|__| W I R E L E S S F R E E D O M
-----------------------------------------------------
This is the buildsystem for the OpenWrt Linux distribution.
To build your own firmware you need a Linux, BSD or MacOSX system (case
sensitive filesystem required). Cygwin is unsupported because of the lack
of a case sensitive file system.
You need gcc, binutils, bzip2, flex, python, perl, make, find, grep, diff,
unzip, gawk, getopt, subversion, libz-dev and libc headers installed.
1. Run "./scripts/feeds update -a" to obtain all the latest package definitions
defined in feeds.conf / feeds.conf.default
2. Run "./scripts/feeds install -a" to install symlinks for all obtained
packages into package/feeds/
3. Run "make menuconfig" to select your preferred configuration for the
toolchain, target system & firmware packages.
4. Run "make" to build your firmware. This will download all sources, build
the cross-compile toolchain and then cross-compile the Linux kernel & all
chosen applications for your target system.
Sunshine!
Your OpenWrt Community
http://www.openwrt.org