You cannot select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
3c0e2aa63e
I-O DATA WN-DX1167R is a 2.4/5 GHz band 11ac rotuer, based on MediaTek MT7621A. Specification: - SoC : MediaTek MT7621A - RAM : DDR3 128 MiB - Flash : NAND 128 MiB - WLAN : MediaTek MT7615D (2.4/5 GHz, 2T2R) - Ethernet : 5x 10/100/1000 Mbps - Switch : MediaTek MT7621A (MT7530) - LEDs/Input : 2x/3x (2x buttons, 1x slide-switch) - UART : through-hole on PCB - J5: Vcc, TX, RX, NC, GND - 57600 bps Flash instruction using initramfs image: 1. Boot WN-DX1167R normally 2. Access to "http://192.168.0.1/" and open firmware update page ("ファームウェア") 3. Select the OpenWrt initramfs image and click update ("更新") button to perform firmware update 4. On the initramfs image, perform sysupgrade with squashfs-sysupgrade image 5. Wait ~120 seconds to complete flashing Notes: - configuration in DeviceTree of DBDC (Dual-Band-Dual-Concurrent) mode for MT7615D chip is not supported in mt76 driver - last 0x80000 (512 KiB) in NAND flash is not used on stock firmware - stock firmware requires "customized uImage header" by MSTC (MitraStar Technology Corp.), but U-Boot doesn't - uImage magic (0x0 - 0x3) : 0x434F4D43 (COMC) - header crc32 (0x4 - 0x7) : with data length and data crc32 - image name (0x20 - 0x37) : model ID and firmware versions - data length (0x38 - 0x3b): kernel + rootfs - data crc32 (0x3c - 0x3f) : kernel + rootfs Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com> Reviewed-by: Sungbo Eo <mans0n@gorani.run> |
4 years ago | |
|---|---|---|
| .github | 6 years ago | |
| config | 4 years ago | |
| include | 4 years ago | |
| package | 4 years ago | |
| scripts | 5 years ago | |
| target | 4 years ago | |
| toolchain | 5 years ago | |
| tools | 4 years ago | |
| .gitattributes | 12 years ago | |
| .gitignore | 5 years ago | |
| BSDmakefile | 18 years ago | |
| Config.in | 7 years ago | |
| LICENSE | 8 years ago | |
| Makefile | 5 years ago | |
| README | 5 years ago | |
| feeds.conf.default | 6 years ago | |
| rules.mk | 5 years ago | |
README
_______ ________ __
| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -__| || | | || _|| _|
|_______|| __|_____|__|__||________||__| |____|
|__| W I R E L E S S F R E E D O M
-----------------------------------------------------
This is the buildsystem for the OpenWrt Linux distribution.
To build your own firmware you need a Linux, BSD or MacOSX system (case
sensitive filesystem required). Cygwin is unsupported because of the lack
of a case sensitive file system.
You need gcc, binutils, bzip2, flex, python3.5+, perl, make, find, grep, diff,
unzip, gawk, getopt, subversion, libz-dev and libc headers installed.
1. Run "./scripts/feeds update -a" to obtain all the latest package definitions
defined in feeds.conf / feeds.conf.default
2. Run "./scripts/feeds install -a" to install symlinks for all obtained
packages into package/feeds/
3. Run "make menuconfig" to select your preferred configuration for the
toolchain, target system & firmware packages.
4. Run "make" to build your firmware. This will download all sources, build
the cross-compile toolchain and then cross-compile the Linux kernel & all
chosen applications for your target system.
Sunshine!
Your OpenWrt Community
http://www.openwrt.org