You cannot select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
Davy Hollevoet 394f54ee62 ath79/nand: add support for Netgear WNDR4300TN
This patch adds support for the WNDR4300TN, marketed by Belgian ISP
Telenet. The hardware is the same as the WNDR4300 v1, without the
fifth ethernet port (WAN) and the USB port. The circuit board has
the traces, but the components are missing.

Specifications:
* SoC: Atheros AR9344
* RAM: 128 MB
* Flash: 128 MB NAND flash
* WiFi: Atheros AR9580 (5 GHz) and AR9344 (2.4 GHz)
* Ethernet: 4x 1000Base-T
* LED: Power, LAN, WiFi 2.4GHz, WiFi 5GHz, WPS
* UART: on board, to the right of the RF shield at the top of the board

Installation:

* Flashing through the OEM web interface:
  + Connect your computer to the router with an ethernet cable and browse
    to http://192.168.0.51/
  + Log in with the default credentials are admin:password
  + Browse to Advanced > Administration > Firmware Upgrade in the Telenet
    interface
  + Upload the Openwrt firmware: openwrt-ath79-nand-netgear_wndr4300tn-squashfs-factory.img
  + Proceed with the firmware installation and give the device a few
    minutes to finish and reboot.

* Flashing through TFTP:
  + Configure your wired client with a static IP in the 192.168.1.x range,
    e.g. 192.168.1.10 and netmask 255.255.255.0.
  + Power off the router.
  + Press and hold the RESET button (the factory reset button on the bottom
    of the device, with the gray circle around it, next to the Telenet logo)
    and turn the router on while keeping the button pressed.
  + The power LED will start flashing orange. You can release the button
    once it switches to flashing green.
  + Transfer the image over TFTP:
    $ tftp 192.168.1.1 -m binary -c put openwrt-ath79-nand-netgear_wndr4300tn-squashfs-factory.img

Signed-off-by: Davy Hollevoet <github@natox.be>
[use DT label reference for adding LEDs in DTSI files]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
4 years ago
..
apm821xx apm821xx: add support for the Netgear WNDAP620 and WNDAP660 6 years ago
ar71xx uboot-envtools: ar71xx: add support for gl-ar150/-domino/-mifi 4 years ago
ath79 ath79/nand: add support for Netgear WNDR4300TN 4 years ago
cns3xxx treewide: use the generic board_name function 7 years ago
imx6 imx6: use device-tree compatible for board name 4 years ago
ipq40xx ipq40xx: add support for Buffalo WTR-M2133HP 4 years ago
ipq806x ipq806x: add support for Linksys EA7500 V1 4 years ago
kirkwood kirkwood: use real model names for Linksys devices 4 years ago
lantiq lantiq: use the compatible string as board name 6 years ago
layerscape uboot-envtools: add configuration for Traverse LS1043 boards. 6 years ago
mpc85xx mpc85xx: add support for OCEDO Panda 5 years ago
mvebu mvebu: add support for MACCHIATObin Single Shot 4 years ago
mxs uboot-envtools: mxs: add support for olimex, imx23-olinuxino 4 years ago
oxnas uboot-envtools: fix fw_env.config for ox820/stg-212 5 years ago
pistachio pistachio: remove custom board detection override 7 years ago
ramips ramips: add support for Linksys EA7300 v1 4 years ago
uboot-envtools.sh uboot-envtools: check for config prior to append 4 years ago