You cannot select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
102c8c55f2
Hardware
--------
SoC: Qualcomm IPQ4029
RAM: 512M DDR3
FLASH: - 128MB NAND (Macronix MX30LF1G18AC)
- 4MB SPI-NOR (Macronix MX25R3235F)
TPM: Atmel AT97SC3203
BLE: Texas Instruments CC2540T
attached to ttyMSM0
ETH: Atheros AR8035
LED: WiFi (amber / green)
System (red / green)
BTN: Reset
To connect to the serial console, you can solder to the labled pads next
to the USB port or use your Aruba supplied UARt adapter.
Do NOT plug a standard USB cable into the Console labled USB-port!
Aruba/HPE simply put UART on the micro-USB pins. You can solder yourself
an adapter cable:
VCC - NC
D+ - TX
D- - RX
GND - GND
The console setting in bootloader and OS is 9600 8N1. Voltage level is
3.3V.
To enable a full list of commands in the U-Boot "help" command, execute
the literal "diag" command.
Installation
------------
1. Get the OpenWrt initramfs image. Rename it to ipq40xx.ari and put it
into the TFTP server root directory. Configure the TFTP server to
be reachable at 192.168.1.75/24. Connect the machine running the TFTP
server to the ethernet port of the access point.
2. Connect to the serial console. Interrupt autobooting by pressing
Enter when prompted.
3. Configure the bootargs and bootcmd for OpenWrt.
$ setenv bootargs_openwrt "setenv bootargs console=ttyMSM1,9600n8"
$ setenv nandboot_openwrt "run bootargs_openwrt; ubi part aos1;
ubi read 0x85000000 kernel; bootm 0x85000000"
$ setenv ramboot_openwrt "run bootargs_openwrt;
setenv ipaddr 192.168.1.105; setenv serverip 192.168.1.75;
netget; set fdt_high 0x87000000; bootm"
$ setenv bootcmd "run nandboot_openwrt"
$ saveenv
4. Load OpenWrt into RAM:
$ run ramboot_openwrt
5. After OpenWrt booted, transfer the OpenWrt sysupgrade image to the
/tmp folder on the device.
6. Flash OpenWrt:
$ ubidetach -p /dev/mtd1
$ ubiformat /dev/mtd1
$ sysupgrade -n /tmp/openwrt-sysupgrade.bin
To go back to the stock firmware, simply reset the bootcmd in the
bootloader to the original value:
$ setenv bootcmd "boot"
$ saveenv
Signed-off-by: David Bauer <mail@david-bauer.net>
|
5 years ago | |
|---|---|---|
| .. | ||
| apm821xx | 5 years ago | |
| ar7 | 5 years ago | |
| ar71xx | 5 years ago | |
| arc770 | 5 years ago | |
| archs38 | 5 years ago | |
| armvirt | 5 years ago | |
| at91 | 5 years ago | |
| ath25 | 5 years ago | |
| ath79 | 5 years ago | |
| bcm53xx | 5 years ago | |
| brcm47xx | 5 years ago | |
| brcm63xx | 5 years ago | |
| brcm2708 | 5 years ago | |
| cns3xxx | 5 years ago | |
| gemini | 5 years ago | |
| generic | 5 years ago | |
| imx6 | 5 years ago | |
| ipq40xx | 5 years ago | |
| ipq806x | 5 years ago | |
| ixp4xx | 5 years ago | |
| kirkwood | 5 years ago | |
| lantiq | 5 years ago | |
| layerscape | 5 years ago | |
| malta | 5 years ago | |
| mediatek | 5 years ago | |
| mpc85xx | 5 years ago | |
| mvebu | 5 years ago | |
| mxs | 5 years ago | |
| octeon | 5 years ago | |
| octeontx | 5 years ago | |
| omap | 5 years ago | |
| orion | 5 years ago | |
| oxnas | 5 years ago | |
| pistachio | 5 years ago | |
| ramips | 5 years ago | |
| rb532 | 5 years ago | |
| samsung | 5 years ago | |
| sunxi | 5 years ago | |
| tegra | 5 years ago | |
| uml | 5 years ago | |
| x86 | 5 years ago | |
| zynq | 5 years ago | |
| Makefile | ||