With failsafe disabled there is no point in early network setup. We
don't send announcement over UDP and there is no way to ssh to the
device.
A side effect of this is avoiding a possibly incorrect network config
(only with failsafe disabled). This problem is related to possible
changes made by user in /etc/config/network.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
When processes don't die on SIGKILL (usually because of kernel bugs), it's
better to give up instead of looping forever.
upgraded will trigger a reboot in this case (and if this fails, a hardware
watchdog will eventually time out and reset the system, if present).
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
For targets using the generic board detection and board specific
settings in diag.sh, the board name is still unset at the time the
set_state() provided by diag.sh is called by 10_indicate_preinit.
Change the execution order to ensure the boardname is populated before
required the first time. Do the target specific board detection as
early as possible, directly followed by the generic one to allow a
seamless switch to the generic function for populating /tmp/sysinfo/.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Depending on busybox applet selection, paths of basic utiilties may differ,
and may not work as symlinks to busybox. Simply using whatever binary is
found in PATH and detecting symlinks automatically is more robust and
easier to maintain.
The list of binaries is also slightly cleaned up and duplicates are
removed.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
This is needed for an upcoming change to the hotplug default rules which
will cause /dev/tty* nodes to get assigned to the "tty" group in order
to support unprivileged user access when needed.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Including version.mk sets PKG_CONFIG_DEPENDS to config entries used for
VERSION_SED command. We should keep these configs to make sure package
gets refreshed when needed.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
There already exist static assignment of uid/gid 65533 in packages feed
and we have nobody/nogroup taking 65534 as their ids. Let's change the
pid of dynamic assignment to start from 65536 so that the two assignment
scheme will not collide with each other
While at it, fix the scan command checking existence of uid/gid
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
The offset and factor are only related for LEDs which can have
different brightness values. But binary LEDs are more common and don't
require any further configuation than setting the factor to 1.
Use offset = 0 and factor = 1 in case nothing else is specified.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Don't pass the value unconditionally to swconfig as a parameter but
instead only call reset if it is 1.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
* Change network_get_subnet6() to sensibly guess a suitable prefix
Attempt to return the first non-linklocal, non-ula range, then attempt
to return the first non-linklocal range and finally fall back to the
previous behaviour of simply returning the first found item.
* Fix network_get_ipaddrs_all()
Instead of replicating the flawed logic appending a fixed ":1" suffix
to IPv6 addresses, rely on network_get_ipaddrs() and network_get_ipaddrs6()
to build a single list of all interface addresses.
* Fix network_get_subnets6()
Instead of replicating the flawed logic appending a fixed ":1" suffix
to IPv6 addresses, rely on the ipv6-prefix-assignment.local-address
field to figure out the proper network address.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Rework the network_get_ipaddr6() and network_get_ipaddrs6() functions to
fetch the effective local IPv6 address of delegated prefix from the
"local-address" field instead of naively hardcoding ":1" as static suffix.
Fixes FS#829.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
mvebu was modifying RAMFS_COPY_BIN and RAMFS_COPY_DATA from a
sysupgrade_pre_upgrade hook. As the ramfs is created from stage2, this
did not have an effect anymore after the staged sysupgrade changes.
As it doesn't really hurt to copy fw_printenv and fw_setenv
unconditionally, simply add them in /lib/upgrade/platform.sh, so stage2
will see them.
Config copying is moved to a function called by platform_copy_config, where
it belongs.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Fixes: FS#821
Fixes: 30f61a34b4 "base-files: always use staged sysupgrade"
The sender domain has a DMARC Reject/Quarantine policy which disallows
sending mailing list messages using the original "From" header.
To mitigate this problem, the original message has been wrapped
automatically by the mailing list software.
This patch is in continuation of: commit 93aa860405
"procd: nand: make it possible to configure kernel and ubi partition"
The $CI_KERNPART variable should be used in place
of the fixed "kernel" partition name. This allows
targets to specifiy alternate names for the kernel
partition.
Cc: Chris Blake <chrisrblake93@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Some functions only used by stage2 are moved there from common.sh.
One piece that could still use more cleanup is platform_pre_upgrade: many
targets reference files from there are aren't available in the ramfs, so
we need to evaluate it before the switch; conversely, flash writes happen
in that function on some targets. Targets that do the latter should be
fixed eventually to use platform_do_upgrade for that purpose.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Support for the -d and -p options is dropped; it may be added again at some
point by adding these flags to the ubus sysupgrade call.
A downside of this is that we get a lot less information about the progress
of the upgrade: as soon as the actual upgrade starts, all shell sessions
are killed to allow unmounting the root filesystem.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
We always want to support staged upgrades now, so it's better to include
upgraded into the main package. /lib/upgrade/nand.sh is moved to
base-files.
The procd-nand-firstboot package is removed for now, it may return later
as a separate package.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
This reverts commit e96a9a9af8.
The change breaks sysupgrade through LuCI and two-stage sysupgrade on
NAND targets. There is also a mismatch of file paths in lock and unlock
operations.
This commit was apparently neither properly tested, nor reviewed, so
drop it for now.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Bug introduced with 6713694.
I did not count on procd handling reload as mentioned
in this doc:
https://wiki.openwrt.org/inbox/procd-init-scripts
```
procd_set_param file /var/etc/your_service.conf # /etc/init.d/your_service reload will restart the daemon if these files have changed
procd_set_param netdev dev # likewise, except if dev's ifindex changes.
procd_set_param data name=value ... # likewise, except if this data changes.
```
The service would be restarted regardless of any of those params.
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
uci_set_leds_ataport() allows to set a led to show activity
on a specific (s)ata port, which is needed for devices that have
a Sata led for each sata port.
The led trigger is from the 834-ledtrig-libata.patch LEDE kernel patch.
uci_set_leds_usbhost() allows to set a led to show total usb activity.
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
[Jo-Philipp Wich: use a single underscore to denote private functions]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
create a function with code common to all led functions,
create another function with code common to functions setting
a simple led trigger, restore alphabetical order in function names.
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
[Jo-Philipp Wich: use a single underscore to denote private functions]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Commit 2036ae4 (base-files: support hostname and ntp servers through board.d)
was supposed to implement these procedures but lacked the required changes
to uci-defaults.sh.
Add the missing procedures now to fix config generation on targets relying
on hostname or NTP server presetting.
Fixes FS#754.
Reported-by: Cristian Morales Vega <cristian@samknows.com>
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This was also working before, with a slightly
different semantic.
[ Original semantic ]
If no reload hooks was implemented, the default one would
kick in, it would return fail, and restart would happen.
This would happen also in the case where a reload hook
would be implemented, it would fail, and it would restart
the service.
[ New semantic ]
The default reload hook calls restart.
Services can implement their own reload.
If reload fails, then the '/etc/init.d/<service> reload'
would return a non-zero code, and the caller can choose
a way to handle this.
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Overwrite an already set proto if a new one is passed to
_ucidef_set_interface() similar to what is done for the interface.
It is required when using ""ucidef_set_interface_wan 'ptm0' 'pppoe'"
after some initial wan interface configuration is already done by
ucidef_add_switch.
The "json_is_a protocol string" guard is meant to not reset an earlier
set interface proto in case something like
"ucidef_set_interface_lan 'eth0'" is used afterwards.
Signed-off-by: Mathias Kresin <dev@kresin.me>
This can be used to tweak the buildbot behavior without having to change
buildbot's configuration.
It will also allow us to add more aggressive clean steps (e.g. on
toolchain changes), which would break developers' workflows if enable
by default.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
When running wifi detect, the user will be told on error output that
wifi detect is deprecated, that wifi config must be used instead. Also
the commit that changes it is referenced for further info.
Signed-off-by: David Pinilla Caparrós <dpinitux@gmail.com>
Since commit 5f8f8a3661 wifi detect does
not longer work and wifi config it's used to configure not yet
configured wireless devices.
This commit changes command usage to reflect that change.
Signed-off-by: David Pinilla Caparrós <dpinitux@gmail.com>
Instead of only using tagged CPU port configurations when more than one VLAN
is present on the switch, always emit tagged configurations unless a board
explicitely opts out of this behaviour by using the previously introduced
[0-9]u@netdev syntax.
Emitting default tagged configurations has the following benefits:
- Relation of switch vlans to netdevs is easier to understand, especially
for multi-cpu-port switches
- Adding additional VLANs (e.g. to break out a LAN port for other purposes)
becomes easier as users are not forced to change the existing untagged
VLAN to tagged and the existing ifname notation from ethX to ethX.Y
anymore, drastly reducing the likelyhood of soft-bricks.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The condition is always true due to the literal string followed the
-n test parameter. A model name set by target scripts always gets
overwritten this way.
Change the condition to check for an already existing destination file
as it was before 5e85ae9 ("base-files: fix error message during boot").
Signed-off-by: Mathias Kresin <dev@kresin.me>
The name will appear in shell prompt and LuCI page title. Uppercase
letters seem to be more vigorous
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
If only a single opkg control file exists (which can happen with
CONFIG_CLEAN_IPKG), grep would not print the file name by default. Instead
of forcing it using -H, we just switch to -l (print only file names) and
get rid of the cut.
Add -s to suppress an error message when no control files exist.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Knowing the package architecture at runtime can be useful, e.g. to
configure opkg repository URLs. The value of ARCH_PACKAGES ("%A" in
VERSION_SED) as added to openwrt_release (as DISTRIB_ARCH) and os-release
(as LEDE_ARCH).
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
It has never been used by default (due to being too bloated), and it is
properly replaced by usign (which has been the default for a long time
now).
Remove this feature to simplify the build system
Signed-off-by: Felix Fietkau <nbd@nbd.name>
currently (after blogic's edit to my commit) it prints like this:
root@lede:/# service aa
aa does not exist. the following services are available :adblock dnsmasq gpio_switch rpcd system
boot done led sqm uhttpd
crelay dropbear log sysctl umount
cron firewall network sysfixtime urandom_seed
ddns fstab odhcpd sysntpd
which looks pretty bad, and is even worse if someone writes only "service" without arguments, as it will print " does not exist. " which is confusing.
with this commit it looks like this:
root@lede:/# service
service "" not found, the following services are available:
adblock dnsmasq gpio_switch rpcd system
boot done led sqm uhttpd
crelay dropbear log sysctl umount
cron firewall network sysfixtime urandom_seed
ddns fstab odhcpd sysntpd
Yes there is some play with " and ', it is to display "name" or just "" if no service name is entered (like in the example).
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
This adds support for install-overlay define. When used in package it
allows installing files to a special directory that gets copied to the
root when installing it.
It allows overwriting files provided by other packages.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Calling a build ##.##-CURRENT might mislead users into thinking that this
build is the most current release of a branch.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Now that the VERSION_NUMBER variable holds the human friendly name and not
the commit ID anymore, we need to support adding the revision ID as well.
Introduce a new config variable CONFIG_VERSION_CODE_FILENAMES which, if set,
causes the resulting file names to contain a commit ID designation as printed
by scripts/getver.sh.
Also sanitize the input variables to ensure that the resulting strings are
lowercased and no not contain spaces.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Move the revision info to the VERSION_CODE variable and default VERSION_NUMBER
to CURRENT for master branch builds.
Also introduce a new menuconfig option CONFIG_VERSION_CODE which allows users
to override the revision value put into VERSION_CODE and adjust the template
files used by the base-files package to accomodate for the changed semantics.
While we're at it, also adjust the various URLs to match the current web site.
After this commit, the relevent files will look like the examples given below:
# cat /etc/openwrt_version
r2398+1
# cat /etc/openwrt_release
DISTRIB_ID='LEDE'
DISTRIB_RELEASE='CURRENT'
DISTRIB_REVISION='r2398+1'
DISTRIB_CODENAME='reboot'
DISTRIB_TARGET='x86/64'
DISTRIB_DESCRIPTION='LEDE Reboot CURRENT r2398+1'
DISTRIB_TAINTS='no-all override'
# cat /usr/lib/os-release
NAME="LEDE"
VERSION="CURRENT, Reboot"
ID="lede"
ID_LIKE="lede openwrt"
PRETTY_NAME="LEDE Reboot CURRENT"
VERSION_ID="current"
HOME_URL="http://lede-project.org/"
BUG_URL="http://bugs.lede-project.org/"
SUPPORT_URL="http://forum.lede-project.org/"
BUILD_ID="r2398+1"
LEDE_BOARD="x86/64"
LEDE_TAINTS="no-all override"
LEDE_DEVICE_MANUFACTURER="LEDE"
LEDE_DEVICE_MANUFACTURER_URL="http://lede-project.org/"
LEDE_DEVICE_PRODUCT="Generic"
LEDE_DEVICE_REVISION="v0"
LEDE_RELEASE="LEDE Reboot CURRENT r2398+1"
On a release branch, those files would look like:
# cat /etc/openwrt_version
r2399
# cat /etc/openwrt_release
DISTRIB_ID='LEDE'
DISTRIB_RELEASE='16.12-CURRENT'
DISTRIB_REVISION='r2399'
DISTRIB_CODENAME='test_release'
DISTRIB_TARGET='x86/64'
DISTRIB_DESCRIPTION='LEDE Test Release 16.12-CURRENT r2399'
DISTRIB_TAINTS='no-all override'
# cat /usr/lib/os-release
NAME="LEDE"
VERSION="16.12-CURRENT, Test Release"
ID="lede"
ID_LIKE="lede openwrt"
PRETTY_NAME="LEDE Test Release 16.12-CURRENT"
VERSION_ID="16.12-current"
HOME_URL="http://lede-project.org/"
BUG_URL="http://bugs.lede-project.org/"
SUPPORT_URL="http://forum.lede-project.org/"
BUILD_ID="r2399"
LEDE_BOARD="x86/64"
LEDE_TAINTS="no-all override"
LEDE_DEVICE_MANUFACTURER="LEDE"
LEDE_DEVICE_MANUFACTURER_URL="http://lede-project.org/"
LEDE_DEVICE_PRODUCT="Generic"
LEDE_DEVICE_REVISION="v0"
LEDE_RELEASE="LEDE Test Release 16.12-CURRENT r2399"
On a release tag, those files would look like:
# cat /etc/openwrt_version
r2500
# cat /etc/openwrt_release
DISTRIB_ID='LEDE'
DISTRIB_RELEASE='17.02.1'
DISTRIB_REVISION='r2500'
DISTRIB_CODENAME='mighty_unicorn'
DISTRIB_TARGET='x86/64'
DISTRIB_DESCRIPTION='LEDE Mighty Unicorn 17.02.1 r2500'
DISTRIB_TAINTS='no-all override'
# cat /usr/lib/os-release
NAME="LEDE"
VERSION="17.02.1, Mighty Unicorn"
ID="lede"
ID_LIKE="lede openwrt"
PRETTY_NAME="LEDE Mighty Unicorn 17.02.1"
VERSION_ID="17.02.1"
HOME_URL="http://lede-project.org/"
BUG_URL="http://bugs.lede-project.org/"
SUPPORT_URL="http://forum.lede-project.org/"
BUILD_ID="r2500"
LEDE_BOARD="x86/64"
LEDE_TAINTS="no-all override"
LEDE_DEVICE_MANUFACTURER="LEDE"
LEDE_DEVICE_MANUFACTURER_URL="http://lede-project.org/"
LEDE_DEVICE_PRODUCT="Generic"
LEDE_DEVICE_REVISION="v0"
LEDE_RELEASE="LEDE Mighty Unicorn 17.02.1 r2500"
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Acked-by: Felix Fietkau <nbd@nbd.name>
"service" is a simple wrapper that will allow to call init.d scripts
current method: # /etc/init.d/network reload
with the wrapper: # service network reload
If the wrapper is called without arguments or with a wrong init script name, it will print an error and list the content of /etc/init.d/ folder
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
Packages that do a killall <cmd> with the same name as the init script
will fail the prerm step when the service isn't running. Do make them
removable without having to restart the service, ignore the return code.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Acked-by: Jo-Philipp Wich <jo@mein.io>
Properly stop/start services on upgrade, but don't change the enabled
state.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Acked-by: Jo-Philipp Wich <jo@mein.io>
Use fwtool to extract it, only require metadata to be present if the
platform sysupgrade script sets REQUIRE_IMAGE_METADATA=1
Image metadata is in JSON format and contains a list of supported
devices, along with version information that could be displayed by a UI
later before the actual upgrade happens.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
A firmware compiled with BUSYBOX_CONFIG_ARP should also use by default the
arp binary from busybox. Otherwise the extra functionality the user
requested can only be used when running arp with the path to the binary.
Signed-off-by: Marek Lindner <marek.lindner@open-mesh.com>
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
Currently, the wifi detection script is executed as part of
the (early) boot process. Pluggable wifi USB devices, which
are inserted at a later time are not automatically
detected and therefore they don't show up in LuCI.
A user has to deal with wifi detection manually, or restart
the router.
However, the current "sleep 1" window - which the boot
process waits for wifi devices to "settle down" - is too
short to detect wifi devices for some routers anyway.
For example, this can happen with USB WLAN devices on the
WNDR4700. This is because the usb controller needs to load
its firmware from UBI and initialize, before it can operate.
The issue can be seen on a BT HomeHub 5A as well as soon as
the caldata are on an ubi volume. This is because the ath9k
card has to be initialized by owl-loader first. Which has to
wait for the firmware extraction script to retrieve the pci
initialization values inside the caldata.
This patch moves the wifi configuration to hotplug scripts.
For mac80211, the wifi configuration will now automatically
run any time a "ieee80211" device is added. Likewise
broadcom-wl's script checks for new "net" devices which
have the "wl$NUMBER" moniker.
Issues with spawning multiple interface configuration - in
case the detection script is run concurrently - have been
resolved by using a named section for the initial
configuration. Concurrent configuration scripts will now
simply overwrite the same existing configuration.
A workaround which preserves the "sleep 1" window for just
the first boot has been added. This allows the existing
brcm47xx boot and mvebu uci-default scripts to correctly
setup the initial mac addresses and regulatory domain.
And finally, the patch renames the "wifi detect" into
"wifi config". As the script no longer produces any output
that has to be redirected or appended to the configuration
file.
Thanks to Martin Blumenstingl for helping with the implementation
and testing of the patch.
Acked-by: Jo-Philipp Wich <jo@mein.io>
Signed-off-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Previously, wifi detect simply dumped its generated wireless
configuration to STDOUT. A second step was needed to append
the configuration to /etc/config/wireless (or create it, if
it didn't exist).
With this patch, The wifi detection script will now use uci
to update the wireless configuration directly.
This patch also makes the initially created wifi-iface a
named section ('default_radio$X' for mac80211 and
'default_wl$X' for broadcom). With this change, uci will
not print the cfgHASH to STDOUT (which would now corrupt
the wireless configuration). It will also prevent adding
duplicated wifi interface configurations, if the wifi
configuration is run concurrently.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch adds a check in "wifi detect" to test if the wireless
configuration file does exist. If it doesn't exist, an empty
/etc/config/wireless file will be created.
This is necessary because uci doesn't create new files,
instead the tool just exits with "uci: Entry not found".
Signed-off-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Introduce support for a new [0-9]u@netdev syntax to ucidev_add_switch() to let
board.d network files request default network switch configurations which do
not use tagged CPU ports.
This commit itself has no effect on generated configurations at the moment
since we still emit untagged configurations by default but it allows boards to
opt-out from default tagged configs in case we start emitting tagged settings
by default.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
We need to tell hwclock with -u commandline option, that we would like
to keep our RTC clock in UTC timezone. Linux kernel expects RTC in UTC
timezone anyway.
In current state of things, we don't tell hwclock to load/store time
from/to RTC in UTC timezone so it uses the timezone from the system
time. If it's set to different timezone then UTC, sysfixtime is going to
screw the time in RTC.
I've following in the setup script:
uci set system.@system[0].timezone='CET-1CEST,M3.5.0,M10.5.0/3'
uci set system.@system[0].zonename='Europe/Prague'
I've this RTC setup (rtc1 is RTC on i.MX6 SoC, rtc0 is battery backed RTC mcp7941x):
rtc-ds1307 3-006f: rtc core: registered mcp7941x as rtc0
snvs_rtc 20cc000.snvs:snvs-rtc-lp: rtc core: registered 20cc000.snvs:snvs-r as rtc1
Then we can experience following (current time is 10:15am):
$ date
Fri Oct 21 10:15:07 CEST 2016
$ hwclock -r -f /dev/rtc0
Fri Oct 21 08:14:46 2016 0.000000 seconds
$ hwclock -u -r -f /dev/rtc0
Fri Oct 21 10:14:46 2016 0.000000 seconds
And after current broken sysfixtime:
$ /etc/init.d/sysfixtime stop
$ date
Fri Oct 21 10:15:25 CEST 2016
$ hwclock -r -f /dev/rtc0
Fri Oct 21 10:15:31 2016 0.000000 seconds
Now we've time in our battery backed RTC in CEST timezone instead of
UTC. Then once again, but with this patch applied to sysfixtime, where
hwclock is using correctly the -u parameter:
$ /etc/init.d/sysfixtime stop
$ date
Fri Oct 21 10:15:53 CEST 2016
$ hwclock -r -f /dev/rtc0
Fri Oct 21 08:15:55 2016 0.000000 seconds
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Acked-by: Jo-Philipp Wich <jo@mein.io>
Currently the reset script will try to run jffs2reset on boards that are
running a rw rootfs, such as ext4. This will cause jffs2reset to fail
and the board to never reboot while the LED blinks until a manual
reboot.
This commit does two different things:
1. Disables reset on boards that do not have an overlay mount
2. Disables the Blinking LED after 5 seconds if the board does not
support reset
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
mkfs.ext4 und losetup are needed for sysupgrade support on mmc devices
with automatic rootfs split (loopback device usage).
Signed-off-by: André Valentin <avalentin@marcant.net>
This helper allows using usbport trigger directly. It requires usbport
compatible syntax and supports specifying multiple USB ports, e.g.:
ucidef_set_led_usbport "usb" "USB" "devicename:colour:function" "usb1-port1" "usb2-port1"
This adds a proper object to the board.json, e.g.
"usb": {
"name": "USB",
"type": "usbport",
"sysfs": "devicename:colour:function",
"ports": [
"usb1-port1",
"usb2-port1"
]
}
and supports translating it into uci section.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This makes init.d script handle existing UCI entries using the new
trigger. It also switches all targets to use its package.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Before a configuration is generated, an empty file is created to store
it in. (required by UCI)
If something happens during config generation
(power cut, interruption, ..) an empty file exists and it is never
regenerated again, causing some daemons to fail starting
(NTPD, logread, ..)
Fix this by also generating new configs if a critical file
is empty.
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
This patch removes the non-working wifi driver filter for
the wifi detection script.
I figured that rather than replacing ${2:-$DRIVERS} with
${1:-$DRIVERS}, it would be better to remove it. Nobody
needed it in the previous years.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Now that we know that the password is in /etc/shadow and not in
/etc/passwd, we can properly fix the logic for the empty password check.
Only 'root::' is an empty password, 'root❌' and 'root:!:' allow no
password login at all.
This fixes the empty password warning still showing after the root password
has been locked using 'passwd -l root' (e.g. to allow public-key auth
only).
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Local variable declarations outside of functions are illegal since the Busybox
update to v1.25.0, therfore remove them from the appropriate places.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
oneshot trigger configurations for LEDs are created, but the on/off
timing configurations are ignored. generate_config is correctly creating
oneshot configs, but the later led script doesn't recognise the trigger
details.
Fixes: c0c3f2d4c9 leds: support oneshot as well as timer triggers
Signed-off-by: Karl Palsson <karlp@etactica.com>
Due to an empty pi_ifname in the generic failsafe setup, the deconfig
never removed the failsafe networking interface, causing broken
networking later on.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Also configure the switch based on the failsafe config, and create the
failsafe interface as tagged if necessary.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
In preparation of properly setting up vlans and switches, add
support for configuring failsafe on a vlan tagged interface.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Move preinit interface and ip config to its own function to allow
calling it from more than one place.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Instead of board_detect generating the config as a side effect, let
config_generate call board_detect as needed.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
The pi_* variables and the fs_failsafe_wait_timeout variable are set by
the CONFIG_TARGET_PREINIT_* config options. No need to maintain the same
values twice.
All other fs_ variables were never used.
Signed-off-by: Mathias Kresin <dev@kresin.me>
sysupgrade immediately reboots after flashing an image and doesn't
allow to unmount filesystems. At least in case the image used for
sysupgrade is stored on a FAT formatted usb flash drive, the following
warning is printed during the next mount of the flash drive:
FAT-fs (sda1): Volume was not properly unmounted. Some data may be
corrupt. Please run fsck.
Although a data corruption during read operations is unlikely, there is
no need to scare the users.
Signed-off-by: Mathias Kresin <dev@kresin.me>
/etc/init.d/boot tried to create /dev/root based on the kernel's
cmdline which won't work on any recent targets. Remove that code now
that fstools can detect the mounted rootfs based on
/proc/self/mountinfo and /dev/root was long gone anyway.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Network drivers typically allocate memory in atomic context. For that to
be reliable, there needs to be enough free memory. Set the value
heuristically based on the total amount of system RAM.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Treat 'relayd' as an essential service to avoid connection interruptions during sysupgrade on devices configured as a pseudobridge.
Signed-off-by: Conn O'Griofa <connogriofa@gmail.com>
Previous implementation was blocking the init and
breaking halt/reboot/sysupgrade (reported by Daniel Golle)
v2: use procd logging, use set -e + trap for error handling
Signed-off-by: Etienne CHAMPETIER <champetier.etienne@gmail.com>
Tested-by: Daniel Golle <daniel@makrotopia.org>
This commit:
1) seed /dev/urandom with the saved seeds as early as possible
(see /lib/preinit/81_urandom_seed)
2) save a seed at /etc/urandom.seed if it doesn't exists
3) save a new seed each boot at "system.@system[0].urandom_seed"
(see /etc/init.d/urandom_seed)
We use getrandom() so we are sure /dev/urandom pool is initialized
Seed size is 512 bytes (ie /proc/sys/kernel/random/poolsize / 8)
it's the same size as in ubuntu 14.04 and all systemd systems
Seeding /dev/urandom doesn't change entropy estimation, so we still have
"random: ubus urandom read with 4 bits of entropy available"
messages in the logs, but we can now ignore them if
after "urandom-seed: Seeding with ..." message
Saving a new seed on each boot is disabled by default to avoid too much
writes without user consent
v2: log preinit messages to /dev/kmsg
v3: use non generic function name for logging, as /lib/preinit/ files
are all sourced together in /etc/preinit
v4: after a lot of discussion on the ML, use a uci config param
v5: config param is now the path of the seed
Signed-off-by: Etienne CHAMPETIER <champetier.etienne@gmail.com>
Acked-by: Jo-Philipp Wich <jo@mein.io>
dnsmasq's dnssec time checking method now uses a ntp hotplug mechanism,
therefore dnsmasq.time is redudant and no longer needs to be explicitly
excluded from sysfixtime.
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
/etc/os-release is the standard distribution release information
file, therefore add it (and image configuration options for
fields not previously present in LEDE). Once it is deemed
reasonable the non-standard openwrt_release, openwrt_version,
and device_info files could be removed (that is with this patch
we consider them deprecated in favour of the standard file).
Signed-off-by: Daniel Dickinson <lede@daniel.thecshore.com>
Increase the default system log buffer size
from 16 kB (built-in default in ubox logd)
to 64 kB by setting the option in /etc/config/system.
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
Record the state of any hardware LED configured through UCI and use that
information to revert the state when applying updated settings while
maintaining default behaviour of system LEDs.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The board_detect framework is now able to create the entire system config from
scratch so we can finally drop the copy shipped by base-files.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Now that config_generate is able to generate the entire /etc/config/system
from scratch we can apply the same logic as used for /etc/config/network;
when the configuration file exists already then do not do anything, else
generate it from the values provided by /etc/board.json .
In order to facilitate that move the file existance checking inside
/bin/config_generate and call it unconditionally from /bin/board_detect.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Attempt to reset all LED states before applying the UCI configuration to
avoid leaving disabled LEDs behind in lingering glowing state, e.g. when
changing the sysfs entry in the config from one hardware LED to another.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Some package postinstall operations, e.g. those emitted by the LuCI build
system, source and delete the uci-defaults themselves upon package insteall,
causing the generic defaults apply code to trigger shell errors like:
.../luci-app-ddns.postinst: .: line 130: can't open './40_luci-ddns'
Rework the generic apply code to check the existence of the uci-defaults
script before trying to source it, use sed to prefilter the list of entries
from the control file and perform the directory change in a subshell,
avoiding the need for cd $OLDPWD.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Generalize the partition discovery in sysupgrade in order to fix sysupgrade
and config backup/recovery on MMC block devices which use a different naming
scheme compared to mtdblock or sd* devices.
The change also adds the find applet to the ramdisk utilities so that upgrade
code can rely on it.
The commit is based on the initial submission by Russell Senior at
http://patchwork.ozlabs.org/patch/625440/ .
Signed-off-by: Russell Senior <russell@personaltelco.net>
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Centralize setting all version information in include/version.mk
* Set RELEASE env variable in include/version.mk instead of toplevel.mk.
Stop exporting the variable.
* Remove hardcoded release name from /etc/banner
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
Typo, missing space before ] in previous commit caused shell syntax
failure and incorrect restoration of time.
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
dnsmasq maintains dnsmasq.time across reboots and uses it as a means of
determining if current time is good enough to validate dnssec time
stamps. By including /etc/dnsmasq.time as a time source for sysfixtime,
the mechanism was effectively defeated because time was set to the
last time that dnsmasq considered current even though that time is in
the past. Since that time is out of date, dns(sec) resolution would
fail thus defeating any ntp based mechanisms for setting the clock
correctly.
In theory the process is defeated by any files in /etc that are newer
than /etc/dnsmasq.time however dnsmasq now updates the file's timestamp
on process TERM so hopefully /etc/dnsmasq.time is the latest file
timestamp in /etc as part of LEDE shutdown/reboot.
Either way, including /etc/dnsmasq.time as a time source for
sysfixtime is not helpful.
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
dnsmasq maintains dnsmasq.time across reboots and uses it as a means of
determining if current time is good enough to validate dnssec time
stamps. By including /etc/dnsmasq.time as a time source for sysfixtime,
the mechanism was effectively defeated because time was set to the
last time that dnsmasq considered current even though that time is in
the past. Since that time is out of date, dns(sec) resolution would
fail thus defeating any ntp based mechanisms for setting the clock
correctly.
In theory the process is defeated by any files in /etc that are newer
than /etc/dnsmasq.time however dnsmasq now updates the file's timestamp
on process TERM so hopefully /etc/dnsmasq.time is the latest file
timestamp in /etc as part of LEDE shutdown/reboot.
Either way, including /etc/dnsmasq.time as a time source for
sysfixtime is not helpful.
- Update the terminal window title with the current directory and hostname, if using an xterm-compatible terminal emulator.
- Add ll, an useful alias to ls.
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
The json_select call fails when there are no roles or ports objects in board.json. "json_select .." must not be executed after failing.
This fixes for example LEDs not being set up in /etc/config/system.
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
Packages may install scripts into /etc/uci-defaults to be executed once
after installation, usually at the first boot of the target. This works
fine if the package was installed to the rootfs during build or using
the ImageBuilder.
If the package is installed using opkg during run-time uci-defaults
were applied only after a reboot of the device. Avoid the need to
reboot by evaluting the package's uci-defaults in default-postinst.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Remove the public unatteded buildkey from the opkg package to avoid
having hardcoded keys in tree. Use the external keyring package instead
which can be easily updated by users.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
- Add %A placeholder for substituting the package architecture
- Change %U placeholder to refer to the toplevel repository URL
- Construct package feed URLs relative to the toplevel one to match new layout
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Instead of having two different types adsl and vdsl just create one dsl
type. This way we can use the same luci code for adsl and vdsl and the
config parameters are not so different.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 48944
This patch adds extra parameter to switch LED trigger initialization
functions. New functionality maintains backward compatibility, so
calling functions without setting new speed_mask parameter works
as expected.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
SVN-Revision: 48776
oneshot and timer have the same configuration options, just a different
trigger name.
Signed-off-by: Karl Palsson <karlp@etactica.com>
SVN-Revision: 48770
With this patch sysupgrade will write directly to the partitions
instead of to the main disk. The UUID is copied from the image
to the MBR as well. This prevents the mbr from being completely
overwritten and losing the partition table. The -p option has
been added to maintain the original behavior and overwite the
entire disk with the new image. Tests have been added to ensure
that the image partitions match up with the active partitions.
Signed-off-by: Rob Mosher <nyt-openwrt@countercultured.net>
SVN-Revision: 48682
On systems that have an RTC prefer it to the file-based time fixup (i.e.
use hwclock when there is a permanent clock instead of the faked up time
logic that is needed when there is not RTC).
We can't rely on hctosys kernel feature either as we're usually using
RTC as kernel modules which are usually being loaded after hctosys was
run, leading in the following error:
hctosys: unable to open rtc device (rtc0)
Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
SVN-Revision: 48661
change 48451 tried to add support for uclient-fetch by moving
/usr/bin/wget to /bin/wget, but this change kept the symbolic
link to /bin/busybox as install_bin creates links to param 1
the desired fix is to link to uclient-fetch to wget:
install_bin /bin/uclient-fetch /bin/wget
Signed-off-by: John Clark <inindev@gmail.com>
SVN-Revision: 48483
with r48379 and r48386 the path of wget changed.
respect that and adjust the dirname.
this fixes#21680
Signed-off-by: Bastian Bittorf <bittorf@bluebottle.com>
SVN-Revision: 48451
A previous change to sysupgrade moved the overlay files into upper/
The -c switch generates a list of files to backup, but the sed
calls did not take this into consideration.
Signed-off-by: Rob Mosher <nyt-openwrt@countercultured.net>
SVN-Revision: 48281
The MR18 stores the ath9k eeprom values on the NAND.
This patch makes it possible to retrieve the images
from there.
Signed-off-by: Chris R Blake <chrisrblake93@gmail.com>
SVN-Revision: 47948
Replace former uci-defaults.sh implementation with the uci-defaults-new.sh one
and update all users accordingly.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47867
LEDs which are controlled by a PWM need to use the supplied
max_brightness instead. Otherwise they might appear to be
very dim / broken.
Signed-off-by: Chris R Blake <chrisrblake93@gmail.com>
SVN-Revision: 47854
This adds support for specifying the dsl modem, atm bridge configs and setting
the pppoe protocol for wan.
These additions are required to port the Lantiq target to board.d.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47750
Some boards, e.g. the Sheeva Plug, require the lan interface to be set
to DHCP instead of a static address, therfore support that.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47732
This changes uci-defaults-new.sh, config_generate and all relevant board.d
files in order combine ucidef_add_switch() and ucidef_add_switch_ports() into
a single function.
Also removes now superfluous enable and reset arguments.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47721
Out of 69 switch definitions, only 3 pass something different than "1" as
values for reset and enable, with one of those three being invalid.
This change ...
* removes the reset and enable arguments from ucidef_add_switch()
* unconditionally writes reset:1 and enable:1 to JSON
* converts the three users of nonstandard values to ucidef_add_switch_attr()
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47720
Remove support for now unused ucidef_add_switch_vlan(), move port->vlan and
vlan->interfaces conversion to uci-defaults-new.sh and massively simplify
config_generate.
This change prepares the following upcoming steps:
* Eliminate use of ucidef_set_interface_lan_wan() for switch only devices
* Merge ucidef_add_switch() with ucidef_add_switch_ports()
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47719
Only se4t the force_link property for non-lan, non-wan ifaces as it is
unnecessary in the default cases.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47675
Properly quote variables in ucidef_set_interface_lan() and
ucidef_set_interface_lan(), otherwise interfaces with multiple devices
are not properly written into the configuration.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47673
Add ucidef_set_board_id() and ucidef_set_model_name() procedures to store
model information in the board.json file.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47671
The only user was the hg255d board and config_generate did not even emit
proper uci for it.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47658
Remove extra nesting of rssi leds in the led object and move rssi monitor
declaration to its own object.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47655
Add support for generating vlans solely from the port layout description
given through ucidef_add_switch_ports().
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47639
Add further helper functions to uci-defaults-new.sh for easier declarations
of complex switch layouts.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47638
since r45833 and r45848 the overlayfs is automatically mounted read-only
(and blocks remounts as r/w) when JFFS2 is full. see ticket #19564
because of this normal file deletion is not possible anymore.
if a user logins interactively (e.g. SSH) show a hint for this,
that files must be removed in /overlay/upper/...
v2: fix subject line
Signed-off-by: Bastian Bittorf <bittorf@bluebottle.com>
SVN-Revision: 47623
If the user sets any preinit options in .config, the wrong path may get
applied due to wrong default value in image-config.in and due to Makefile
writing also the unchanged options into 00_preinit.conf
Modify the default path in image-config.in to match the current default
path set by r47080. Also modify the fall-back default in Makefile.
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
SVN-Revision: 47590
FHS mandates presence of /var/tmp on compliant systems.
The lack of /var/tmp was discovered when using MIT Kerberos libraries
which default to that location for storing credentials cache.
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
SVN-Revision: 47219
This URL can be embedded e.g. within UPnP announcements where a link
to the manufacturer's homepage is desired.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
SVN-Revision: 47135
Even though there are not many users left within the OpenWrt tree it seems
this function broke during the kernel 3.18 transition.
Fix it by providing a workdir as required by overlayfs.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
SVN-Revision: 47015
- Simplify user spec parsing code
- Alias IPKG_INSTROOT to shorten code
- Quote variables where appropriate
- Remove a useless-use-of-cat instance
- Suppress errors in case control or list files are missing
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 46975
OpenWrt should support an optional /etc/profile.d directory like
most other Linux distributions. This allows packages to install
their own scripts into /etc/profile.d/ directory.
The file suffix should make clear, that these scripts
are (sourced) shell-snippets. If the user needs e.g. php or lua,
one must make sure that the interpreter is called.
The reverse failsafe test makes sure, that the effective returncode is 0.
A typcal usecase is the inclusion of private helpers,
special variables or aliases, which at the moment needs
patching the sourcecode and is not well maintainable.
Now the builder can simply add there files.
v1 initial work of Hendrik Lüth <hendrik@linux-nerds.de>
v2 changes regarding RFC (e.g. thomas.langer@lantiq.com)
v3 changes regarding RFC (e.g. mschiffer@universe-factory.net)
v4 keep it simple and mimic OpenWrt style
Signed-off-by: Bastian Bittorf <bittorf@bluebottle.com>
SVN-Revision: 46965
Move the pattern setting from netifd's service script to
/etc/sysctl.conf. Put the timestamp component '%t' just after
executable name '%e' for more natural order from output of ls command.
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
SVN-Revision: 46867
This enables passworldless login for root via SSH whenever no root
password is set (e.g. after reset, flashing without keeping config
or in failsafe) and removes telnet support alltogether.
Signed-off-by: Steven Barth <steven@midlink.org>
SVN-Revision: 46809
Using the postinst script for sanity checks and expecting opkg to fail
if the postinst didn't return 0 was possible in Barrier Breaker, propagate
the real postinst return code through default_postinst to restore this
behaviour.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 46653
With this change we let user know 5 seconds have passed and reset button
can be released (to trigger factory reset)
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 46650
We need a+x rights on the path to the root of the jails
so we can use users other than root (like nobody)
This partly fixes jailed dnsmasq
Signed-off-by: Etienne CHAMPETIER <champetier.etienne@gmail.com>
SVN-Revision: 46466
Internal GPIO pins are used for PoE passthrough setups in multi-port
routers. This patch implemnets control over this hardware feature for
Ubiquiti Nanostations and TP-Link CPE510.
Signed-off-by: Lars Kruse <lists@sumpfralle.de>
SVN-Revision: 46271
This changes makes it possible to store custom settings
in individual files inside the directory /etc/sysctl.d/.
Signed-off-by: Stefan Tomanek <stefan.tomanek+openwrt@wertarbyte.de>
SVN-Revision: 46239
get_image allows passing 2nd argument that is used in a pipe for
extracting firmware from a non-native format. By accepting such command
in default_do_upgrade we allow platforms to use this helper for vendor
specific images.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 45900
Instead of stripping everything after the first dot, strip everything
after the last dot.
This fixes pre-/postrm actions for packages with a dot in their name,
like libusb-1.0.
Fixes#19668.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 45702
Depending on configuration, disable the LED before writing the trigger
and enable it after writing it. Fixes LEDs where the value defaults to 1
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 45463
Current NAND sysupgrade process is a bit hard to follow due to the way
of triggering stage1. Currently this is done by leaving a /mark/ in the
form of /tmp/sysupgrade-nand-path during nand_do_platform_check.
Existence of this mark stops standard sysupgrade process (as the result
of sysupgrade_pre_upgrade exit). This may be a bit misleading.
Proposed solution adds a new function that will allow platform.sh
trigger NAND sysupgrade consciously. This will also allow cleaning
nand_do_platform_check limiting it to just checking the image.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 45338
Use xattr to store the filesystem initialization state of the overlay.
As long as the filesystem is not marked as initialized yet (happens in
/etc/init.d/done), all overlay data (except for sysupgrade.tgz) will be
discarded before the system is allowed to boot
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 44942
The name variable contains at first the package name,
and after the last group name.
This patch fixes /etc/rc.d symlink creation (at least).
Change name in pkgname, change the other name in ugname
(user group name), and id in ugid (user group id)
Signed-off-by: Etienne CHAMPETIER <champetier.etienne@gmail.com>
SVN-Revision: 44253
This restores normal pre-r43715 200ms blink-period for the System LED we're all accustomed to see while our OpenWrt routers are booting.
Failsafe possibility will now be signalled with a new 100ms blinking, which is easily recognizable from the normal 200ms booting.
So no existing user will be scared by a new 500ms LED pattern, since such a slow pattern could easily be mistaken for something wrong... I was like "ok why my router is collapsing now, is this a bad flash, a kernel panic, or what else" when I've seen it for the first time ;)
Sorry for not having explained myself better in v1 of this patch.
Original:
Preinit, failsafe is possible: 200ms
Preinit, failsafe not possible anymore, booting normally: 200ms
Failsafe entered: 50ms
Now (after preinit_regular has been introduced):
Preinit, failsafe is possible: 200ms
Preinit, failsafe not possible anymore, booting normally: 500ms *here is the "offending" change*
Failsafe entered: 50ms
With my proposed patch:
Preinit, failsafe is possible: 100ms *indicate this condition with a new timing, that prompts the user to press the key if they want to start failsafe*
Preinit, failsafe not possible anymore, booting normally: 200ms *keep this as before*
Failsafe entered: 50ms
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
SVN-Revision: 44056
The enable and reset settings need to be added even when they're false. This is true at least for 'enable', that seems to default to true otherwise.
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
SVN-Revision: 43887
Change the kconfig default for the repository url template to use "%s"
instead of "%T" as well.
Also complete the kconfig help text do cover the recently introduced
manufacturer, product and hwrev options.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 43872
This commit introduces a new option CONFIG_VERSION_FILENAMES which causes
OpenWrt to embed the version number in generated image files, SDK- and
ImageBuilder archives.
The option is enabled by default if CONFIG_VERSIONOPT is set.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 43869
This new argument is used right after starting regular preinit (which
happens if failsafe wasn't triggered). The main purpose of "preinit"
argument is to indicate that failsafe can be triggered, however we were
missing a way to inform user that we don't wait for a trigger anymore.
With this change it's clear when failsafe mode can be triggered.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 43715
create user:group before running postinst-pkg. the postinst hook might require
the user:group to already exist.
Signed-off-by: Christian Schoenebeck <christian.schoenebeck@gmail.com>
SVN-Revision: 43472
ldd might be called for shell scrips during sysupgrade, causing it to
complain that they are not a dynamic executables.
This is a harmless error, so supress it to avoid confusing about them
being serious ones.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 43315
r36107 ("base-files: sysupgrade fail with eglibc") tried to fix
sysupgrade by changing the ld-soname to what is expected, but only
fixed MIPS while breaking ARM.
The underlying issue is that the ld.so name varies widely across
different architectures for eglibc:
eglibc-2.19-r25243$ grep -r "ld-soname :=" . | awk '{ print $3 }' | sort -u
ld64.so.1
ld64.so.2
ld-linux-aarch64_be.so.1
ld-linux-aarch64.so.1
ld-linux-armhf.so.3
ld-linux-mipsn8.so.1
ld-linux.so.2
ld-linux.so.3
ld-linux-x32.so.2
ld-linux-x86-64.so.2
ld.so.1
Instead of adding each different soname to check for and copy it,
replace the awk script with a sed script to extract it properly and
drop the hardcoded so-name.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 43295
Note, that licensing stuff is a nightmare: many packages does not clearly
state their licenses, and often multiple source files are simply copied
together - each with different licensing information in the file headers.
I tried hard to ensure, that the license information extracted into the OpenWRT's
makefiles fit the "spirit" of the packages, e.g. such small packages which
come without a dedicated source archive "inherites" the OpenWRT's own license
in my opinion.
However, I can not garantee that I always picked the correct information
and/or did not miss license information.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
SVN-Revision: 43155
Stijn Tintel
Rafał Miłecki
Florian Eckert
Matthias Schiffer
Mathias Kresin
Jo-Philipp Wich
Yousong Zhou
Jonas Gorski
Christian Lamparter
Kenneth Johansson
Alexandru Ardelean
Alberto Bursi
Felix Fietkau
Vitaly Chekryzhev
Lucian Cristian
David Pinilla Caparrós
Hans Dedecker
Julian Labus
Marek Lindner
Petr Štetiar
Chris Blake
André Valentin
Pierre Lebleu
Koen Vandeputte
Florian Fainelli
John Crispin
Karl Palsson
Daniel Golle
Conn O'Griofa
Etienne CHAMPETIER
Kevin Darbyshire-Bryant
Daniel Dickinson
Hannu Nyman
Vittorio G (VittGam)
Vittorio Gambaletta (VittGam)
John Crispin
Hauke Mehrtens
John Crispin
Felix Fietkau
Jo-Philipp Wich
Steven Barth
Rafał Miłecki
Jonas Gorski
Luka Perkov
Nicolas Thill
Imre Kaloz