This adds support for kernel 4.14 to the target and directly make it the
default kernel version to use.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Sandeep Sheriker <sandeepsheriker.mallikarjun@microchip.com>
Instead of maintaining 3 very similar subtargets merge them into one.
This does not use the Arm NEON extension any more, because the SAMA5D3
does not support NEON.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Sandeep Sheriker <sandeepsheriker.mallikarjun@microchip.com>
This removes some settings which are normally set by the generic
configuration and should not be changed.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Sandeep Sheriker <sandeepsheriker.mallikarjun@microchip.com>
The configuration of the sama5d4 subtarget was used as the default
configuration and then the subtarget configurations were adapted.
The resulting kernel configuration without any extra modules selected is
still the same.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Sandeep Sheriker <sandeepsheriker.mallikarjun@microchip.com>
The restart button is currently assigned to KEY_POWER power script but
an easily accessible button immediately powering off the device is
undesirable. Switch to using new KEY_POWER2 reboot script with 5 second
seen delay.
Fixes: FS#1965
Signed-off-by: Alan Swanson <reiver@improbability.net>
Signed-off-by: Petr Štetiar <ynezz@true.cz> [long line wrap]
For devices such as BTHOMEHUBV5A with both reset and restart buttons,
its easily accessible restart button has been assigned to KEY_POWER
power script to poweroff preventing accidental (or malicious) factory
resets by KEY_RESTART reset script. However an easily accessible button
immediately powering off the device is also undesirable.
As KEY_RESTART is already used for reset script (and there's no
KEY_REBOOT in Linux input events), use KEY_POWER2 for rebooting via new
reboot script with 5 second seen delay.
Fixes: FS#1965
Signed-off-by: Alan Swanson <reiver@improbability.net>
Signed-off-by: Petr Štetiar <ynezz@true.cz> [long line wrap]
For devices such as BTHOMEHUBV5A with both reset and restart buttons,
its easily accessible restart button has been assigned to KEY_POWER
power script to poweroff preventing accidental (or malicious) factory
resets by KEY_RESTART reset script. However an easily accessible button
immediately powering off the device is also undesirable.
As KEY_RESTART is already used for reset script (and there's no
KEY_REBOOT in Linux input events), use KEY_POWER2 for rebooting via new
reboot script with 5 second seen delay.
Fixes: FS#1965
Signed-off-by: Alan Swanson <reiver@improbability.net>
Signed-off-by: Petr Štetiar <ynezz@true.cz> [long line wrap]
For devices such as BTHOMEHUBV5A with both reset and restart buttons,
its easily accessible restart button has been assigned to KEY_POWER
power script to poweroff preventing accidental (or malicious) factory
resets by KEY_RESTART reset script. However an easily accessible button
immediately powering off the device is also undesirable.
Fixes: FS#1965
Signed-off-by: Alan Swanson <reiver@improbability.net>
Signed-off-by: Petr Štetiar <ynezz@true.cz> [long line wrap]
ade00ca585a4 container: fix .dockerenv stat check
385b904b2f0a hotplug: improve error message during group ownership change
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Add upstream patch from:
https://git.busybox.net/busybox/commit/?id=028c5aa18b5273c029f0278232d922ee1a164de6
The patch fixes a problem with an infinite loop causing 100% CPU usage
when running the following command /lib/preinit/10_indicate_preinit
without the CAP_NET_ADMIN capability (such as in Docker):
ip -4 address flush dev $pi_ifname
Signed-off-by: Mikael Magnusson <mikma@users.sourceforge.net>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> [refresh patch]
This patch fixes following missing bits:
- add missing 'compatible' property on firmware partition
- set vendor partition 'userconfig' read-only
Fixes: 30dcbc741d ("ath79: add support for EnGenius ECB1750")
Signed-off-by: Sven Friedmann <sf.openwrt@okay.ms>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
SoC: AR9344
RAM: 128MB
Flash: 16MiB Winbond 25Q128BVFG SPI NOR
5GHz WiFi: AR9380 PCIe 3x3:3 802.11n
2.4GHz WiFi: AR9344 (SoC) AHB 2x2:2 802.11n
5x Gigabit ethernet via AR8327N switch (green + amber LEDs)
2x USB 2.0 via GL850G hub
4x front LEDs from SoC GPIO
1x front WPS button from SoC GPIO
1x bottom reset button from SoC GPIO
Known issues:
AR8327N LEDs only have default functionality, not presented in sysfs.
This is a regression from ar71xx.
UART header JP1, 115200 no parity 1 stop
TX
GND
VCC
(N/P)
RX
See https://openwrt.org/toh/wd/n750 for flashing detail.
Procedures unchanged from ar71xx.
Tested sysupgrade + factory flash from WD Emergency Recovery
Signed-off-by: Ryan Mounce <ryan@mounce.com.au>
Don't set the default firewall zone to wan if not specified to keep the
behavior aligned with other tunnel protocols like gre and 6rd.
If the interface zone is not specified try to get it from the firewall config
when constructing the procd firewall rule.
While at it only add procd inbound/outbound firewall rules if a zone is specified.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Don't set the default firewall zone to wan if not specified to keep the
behavior aligned with other tunnel protocols like gre and 6rd.
If the interface zone is not specified try to get it from the firewall config
when constructing the procd firewall rule.
While at it only add a procd inbound firewall rule if a zone is specified.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* Feature: Add support for 200Gbps (50Gbps per lane) link mode
* Feature: simplify handling of PHY tunable downshift
* Feature: add support for PHY tunable Fast Link Down
* Feature: add PHY Fast Link Down tunable to man page
* Feature: Add a 'start N' option when specifying the Rx flow hash indirection table.
* Feature: Add bash-completion script
* Feature: add 10000baseR_FEC link mode name
* Fix: qsfp: fix special value comparison
* Feature: move option parsing related code into function
* Feature: move cmdline_coalesce out of do_scoalesce
* Feature: introduce new ioctl for per-queue settings
* Feature: support per-queue sub command --show-coalesce
* Feature: support per-queue sub command --coalesce
* Fix: fix up dump_coalesce output to match actual option names
* Feature: fec: add pretty dump
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This makes sysupgrade work on the D-Link DIR-685 after
initial factory install.
We create the platform.sh script to support sysupgrade
on more targets as we move on with sysupgrade support.
Cc: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
[cleanup in platform.sh, removed superfluous SUPPORTED_DEVICES]
Lua's LNUM patch currently doesn't parse properly certain numbers as
it's visible from the following simple tests.
On x86_64 host (stock Lua 5.1.5, expected output):
$ /usr/bin/lua -e 'print(0x80000000); print(0x80000000000); print(0x100000000)'
2147483648
8796093022208
4294967296
On x86_64 host:
$ staging_dir/hostpkg/bin/lua -e 'print(0x80000000); print(0x80000000000); print(0x100000000)'
-2147483648
0
0
On x86_64 target:
$ lua -e 'print(0x80000000); print(0x80000000000); print(0x100000000)'
-2147483648
0
0
On ath79 target:
$ lua -e 'print(0x80000000); print(0x80000000000); print(0x100000000)'
-2147483648
8796093022208
4294967296
It's caused by two issues fixed in this patch, first issue is caused by
unhadled strtoul overflow and second one is caused by the cast of
unsigned to signed Lua integer when parsing from hex literal.
Run tested on:
* Zidoo Z9S with RTD1296 CPU (aarch64_cortex-a53)
* qemu/x86_64
* qemu/armvirt_64
* ath79
Signed-off-by: Liangbin Lian <jjm2473@gmail.com>
[commit subject/message touches, fixed From to match SOB, fixed another
unhandled case in luaO_str2i, host Lua, package bump]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This reverts commit 0111b86f1d as it
breaks on Linux distributions without ed support
./fix-libmath_h: line 1: ed: command not found
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
When running OpenWrt inside an LXC container no shell is opend as LXC
defaults to a virtual /dev/console.
This patch allows to enter a shell after starting the container via
`lxc-start`, without it is only posible to access a shell on tty1 via
`lxc-console`.
Signed-off-by: Paul Spooren <mail@aparcar.org>
The vendor firmware only uses two mac addresses, the mac address on the
label and the label + 1. While checking multiple devices, all labels have
even mac addresses. Concluding only 2 address are assigned to a device.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
The GL.iNet AR750S USB and microSD port is currently not working out of
the box. GPIO 7 is used to control the power of the USB port. Add GPIO
7 as a fixed-regulator for the port. Also add &usb1 to DTS to get the
microSD port to work.
Signed-off-by: Alexander Wördekemper <alexwoerde@web.de>
This patch fixes `sysupgrade -n` when flashed with rootfs of the same
size as currently running, so the rootfs_data wouldn't get destroyed and
thus survive reboot. So let's fix it by always cleaning up the content
of the rootfs_data during sysupgrade.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
ar71xx uses `archer-c7-v5` for led prefix, but ath79 sticks to more
generic `tplink` as the DTS is reused by more boards, so we need to
perform migrations of the LED names during upgrade.
Cc: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Commit "generic: ar8216: add mib_poll_interval switch attribute" sets
mib-poll-interval as disabled by default (was set to 2s), so it makes
switch LEDs trigger disfunctional on devices which don't have
mib-poll-interval set.
So this patch sets mib-poll-interval to 500ms on devices which are using
ar8xxx switch LEDs trigger, as the same value was set for built in
switches in 443fc9ac35 ("ath79: use ar8216 for builtin switch").
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Commit "generic: ar8216: add mib_poll_interval switch attribute" sets
mib-poll-interval as disabled by default (was set to 2s), so it makes
switch LEDs trigger disfunctional on devices which don't have
mib-poll-interval set.
So this patch sets mib-poll-interval to 500ms on devices which have
ar83xx switch connected to emac0, as the same value was set for built in
switches in 443fc9ac35 ("ath79: use ar8216 for builtin switch").
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Commit "generic: ar8216: add mib_poll_interval switch attribute" sets
mib-poll-interval as disabled by default (was set to 2s), so it makes
switch LEDs trigger disfunctional on devices which don't have
mib-poll-interval set.
So this patch sets mib-poll-interval to 500ms on devices which have
ar83xx switch connected to mdio0 bus, as the same value was set for
built in switches in 443fc9ac35 ("ath79: use ar8216 for builtin
switch").
Some measurements performed on TP-Link Archer C7-v5:
mib-type=0, mib-poll-interval=500ms (10s pidstat)
Average: %usr %system %guest %wait %CPU CPU Command
Average: 0.00 1.93 0.00 0.00 1.93 - kworker/0:2
iperf3 (30s): 334 Mbits/sec
mib-type=0, mib-poll-interval=2s (10s pidstat)
Average: %usr %system %guest %wait %CPU CPU Command
Average: 0.00 1.14 0.00 0.00 1.14 - kworker/0:2
iperf3 (30s): 334 Mbits/sec
So it seems like we get 4x faster LED refresh rate for additional 0.8%
CPU load.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Commit "generic: ar8216: add mib_poll_interval switch attribute" has
added mib_poll_interval global config option and commit "generic:
ar8216: group MIB counters and use two basic ones only by default" has
added mib_type config option.
So this patch adds ucidef_set_ar8xxx_switch_mib helper function which
would allow configuration of the above mentioned new switch config
options.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Commit "generic: ar8216: add mib_poll_interval switch attribute" has added
mib_poll_interval global config option and commit "generic: ar8216: group
MIB counters and use two basic ones only by default" has added mib_type
config option.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
There are too many MIB counters that almost nobody needs since commit
d6366ce366 ("generic: ar8216: mib_work_func: read all port mibs
everytime").
In the worker function to poll MIB data, it deals with all ports instead
of only one port every time, which introduces too many mdio operations
that it becomes a heavy CPU load even on not-emulated MDIO bus.
This commit groups MIB counters and enable only TxBytes and RxGoodBytes
by default (both of which are necessary to get swconfig led working.)
and adds an swconfig attribute to allow enabling all counters if users
need them.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
This allows specifying interval of polling MIB counters from userspace
and allow completely turning off MIB counter support by setting
mib_poll_interval to 0.
Since MIB counter polling is a heavy CPU load for GPIO emulated MDIO
bus, disable this behavior by default. Those who wants to use swconfig
LEDs can enable them with qca,mib-poll-interval dts property or with
swconfig command.
Fixes: FS#2230 ("kworker spikes 100% cpu every 2 second.")
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
This adds the host staging directory to the include path to make it use
the zlib.h files from the staging include directory and also link
against the zlib version from the staging directory.
This fixes a compile problem when the zlib header were not installed on
the build host.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[picked from openwrt-18.06]
The SD-Card polling is now implemented by default in the
fs-tools block-mount utility package. It might not be as
fast as the current detection method since the polling
time is 2 Seconds, but it's much less of an hack.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
c9d9dbf pppoe: Custom host-uniq tag
44012ae plugins/rp-pppoe: Fix compile errors
Refresh patches
Drop 520-uniq patch as upstream accepted
Drop 150-debug_compile_fix patch as fixed upstream
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Sandeep Sheriker M
Hauke Mehrtens
Alan Swanson
Petr Štetiar
Paul Spooren
Mikael Magnusson
Koen Vandeputte
Hans Dedecker
Ryan Mounce
Alexander Couzens
Linus Walleij
Liangbin Lian
Deng Qingfang
Alexander Wördekemper
Chuanhong Guo
Christian Lamparter