Now that $UPGRADE_BACKUP is set conditionally there is no need to check
the $UPGRADE_OPT_SAVE_CONFIG anymore. All conditions can be simplified.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
It's a variable set by procd that should replace hardcoded
/tmp/sysupgrade.tgz.
This change requires the most recent procd with the commit 0f3c136
("sysupgrade: set UPGRADE_BACKUP env variable").
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This var has been replaced by the $UPGRADE_OPT_UPGRADE_OPT_SAVE_CONFIG
Fixes: b534ba9611 ("base-files: pass "save_config" option to the "sysupgrade" method")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
The tar extraction depends on the order in which the files
are added to the tar file. Since the order is not guaranteed
and depends on the host system, the combined mtd write fails
with sysupgrade images built on some systems.
Fix by changing to tar file order independent mtd write.
Fixes: 86e18f6706 ("ipq806x: add support for OpenMesh A42")
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
The sysupgrade_pre_upgrade hook was removed with 5e1b4c57de ("base-files:
drop fwtool_pre_upgrade") while there were still scripts using it:
* target/linux/ar71xx/base-files/lib/upgrade/allnet.sh
* target/linux/ar71xx/base-files/lib/upgrade/openmesh.sh
* target/linux/ipq40xx/base-files/lib/upgrade/openmesh.sh
Not running the hooks can either prevent a successful upgrade or brick the
device because the fw_setenv program cannot be started correctly.
Instead of adding this hook again, the directory /var/lock for fw_setenv
can also just be created directly before fw_setenv is called.
Fixes: 5e1b4c57de ("base-files: drop fwtool_pre_upgrade")
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
* QCA IPQ4019
* 256 MB of RAM
* 32 MB of SPI NOR flash (s25fl256s1)
- 2x 15 MB available; but one of the 15 MB regions is the recovery image
* 2T2R 2.4 GHz
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=20,variant=OM-A62
* 2T2R 5 GHz (channel 36-64)
- QCA9888 hw2.0 (PCI)
- requires special BDF in QCA9888/hw2.0/board-2.bin
bus=pci,bmi-chip-id=0,bmi-board-id=16,variant=OM-A62
* 2T2R 5 GHz (channel 100-165)
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=21,variant=OM-A62
* multi-color LED (controlled via red/green/blue GPIOs)
* 1x button (reset; kmod-input-gpio-keys compatible)
* external watchdog
- triggered GPIO
* 1x USB (xHCI)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x gigabit ethernet
- phy@mdio3:
+ Label: Ethernet 1
+ gmac0 (ethaddr) in original firmware
+ 802.3at POE+
- phy@mdio4:
+ Label: Ethernet 2
+ gmac1 (eth1addr) in original firmware
+ 18-24V passive POE (mode B)
* powered only via POE
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the factory image to the u-boot when the device boots up.
The initramfs image can be started using
setenv bootargs 'loglevel=8 earlycon=msm_serial_dm,0x78af000 console=ttyMSM0,115200 mtdparts=spi0.0:256k(0:SBL1),128k(0:MIBIB),384k(0:QSEE),64k(0:CDT),64k(0:DDRPARAMS),64k(0:APPSBLENV),512k(0:APPSBL),64k(0:ART),64k(0:custom),64k(0:KEYS),15552k(inactive),15552k(inactive2)'
tftpboot 0x84000000 openwrt-ipq40xx-openmesh_a62-initramfs-fit-uImage.itb
set fdt_high 0x85000000
bootm 0x84000000
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Rafał Miłecki
Marek Lindner
Sven Eckelmann
John Crispin