Cisco RV0XX u-boot sets MEM=2048 as boot param. We assume that at least
4MB (mem_alloc_size) of ram is needed to run linux on cavium boards, so
if mem < 4M - ignore it and set default value
Signed-off-by: Michał Osowiecki <michal.osowiecki@gmail.com>
This reverts commit 53147c2237.
These config changes break booting on C2600 and probably other devices.
Signed-off-by: Josh Bendavid <joshbendavid@gmail.com>
omap requires msdos partition to boot from sdcard.
Prepare for upcoming full sdcard image generation.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Commit 9ff8928bb9 renamed the snd-soc-mt7620-i2s
driver and dropped snd-soc-mt7620-wm8960 which selected CONFIG_SND_SOC_WM8960
breaking all ramips builds due to undefined kernel config symbols.
Rework the kmod-sound-mt7620 package to explicitely select the
CONFIG_SND_SOC_WM8960 symbols and change it to bundle the renamed .ko file.
Also remove the @BROKEN flag and exclude it on the rt288x subtarget instead.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
/etc/init.d/fstab had some warnings in it to let users know that they
should call "block mount" directly. these ended up in the bootlog.
fix this by splitting the code into boot() and start(). this way the system
will boot without warning but manually starting the script will lead to the
message.
fixes FS#3
Reported-by: Hannu Nyman <hannu.nyman@iki.fi>
Signed-off-by: John Crispin <john@phrozen.org>
The package Makefile was based on work at link [1] with the following
changes
1. Disable minidebuginfo support thus no dependency on liblzma
2. Add 2 patches for building against musl-libc and building with
mips16 enabled
3. Add LICENSE and DEPENDS info, etc.
[1] https://github.com/rpi-openwrt/rpi-packages/tree/master/libs/libunwind
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
DuZun DM06 is a develop board based on mt7628
64M RAM, 8M SPI Flash, 1 WAN, 1 LAN.
wm8960 codec with line out, line in and speaker output.
Signed-off-by: Michael Lee <igvtee@gmail.com>
* remove mt7620-wm8960.c use simple card and DTS to do it
* add old chips support
* add 12Mhz refclk setup. this is hard code. need use clock framework
rewrite it
* add interrupt error status support for debug. default disable it.
because it cause to many interrupts
* add setup bclk suport not hard code it
* add 24 bits support for mt7628. not verified
* use regmap api to control registers
* add txdma-req/rxdma-req DTS params for DMA use
Signed-off-by: Michael Lee <igvtee@gmail.com>
* add rt_i2c structure to store driver data
* rewrite read/write check function and add i2c error status check.
so we don't need to wait until time out.
* add 10 bits address support. according to the data sheet i think
it is possible. but i haven't verify it.
* the most important is start transfer only need once. otherwise
it cause I2C_STARTERR status.
* add set i2c clock speed register by dts options "clock-frequency".
not just hard code it.
* add mt7621 i2c driver. i just copy i2c-ralink.c and change register
names. and the hardware don't support error status. so i remove it.
but the logic is the same.
Signed-off-by: Michael Lee <igvtee@gmail.com>
* fix compiler error. device_control operation not support now.
* add old chips support 8 channels. new chips support 16 channels.
* add mt7621 hsdma driver. data sheet says it has two channels.
but after test only one channel support.
* add memory to memory DMA support. i use dmatest kernel module to
verify this function. on rt305x it will copy more data. on mt7621
only two channels can works at the same time. these two chips
maybe have hardware bugs. because on other chips don't have these bugs.
* use tasklet to handle remaining dma requests.
Signed-off-by: Michael Lee <igvtee@gmail.com>
John Crispin
Josh Bendavid
Alexander Couzens
Dirk Neukirchen
Jo-Philipp Wich
Rafał Miłecki
Felix Fietkau
Magnus Kroken
Arne Zachlod
Henryk Heisig
Yousong Zhou
Michael Lee