This patch fixes jailed dnsmasq running into the following issue:
|dnsmasq[1]: cannot read /usr/share/dnsmasq/dhcpbogushostname.conf: No such file or directory
|dnsmasq[1]: FAILED to start up
|procd: Instance dnsmasq::cfg01411c s in a crash loop 6 crashes, 0 seconds since last crash
Fixes: a45f4f50e1 ("dnsmasq: add dhcp-ignore-names support - CERT VU#598349")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[bump package release]
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
53792c9 fix typo
df07182 Update German translation.
Remove local patch 001-fix-typo which is a backport of the above 53792c9
There is no practical difference between our test8 release and this rc
release, but this does at least say 'release candidate'
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
A new test case was adding in one of the patches fixing a problem, this
also included a change in the test/Makefile.am to add this test case.
The build system detected a change in the Makefile.am and wants to
regenerate the Makefile.in, but this fails because automake-1.15 is not
installed yet. As automake depends on patch being build first, make sure
we do not modify the Makefile.am.
This fixes build problem seen by the build bots.
Fixes: 4797dddfde ("patch: apply upstream cve fixes")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The Makefile.am changed and now patch wants to use automake to
regenerate the Makefile.in. Make sure automake was build before we build
patch.
This fixes build problem seen by the build bots.
Fixes: 4797dddfde ("patch: apply upstream cve fixes")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Apply two upstream patches to address two CVEs:
* CVE-2018-1000156
* CVE-2018-6952
Add PKG_CPE_ID to Makefile.
Build tested on apm821xx and ar71xx.
Signed-off-by: Russell Senior <russell@personaltelco.net>
This adds support for the WPA3-Enterprise mode authentication.
The settings for the WPA3-Enterpriese mode are defined in
WPA3_Specification_v1.0.pdf. This mode also requires ieee80211w and
guarantees at least 192 bit of security.
This does not increase the ipkg size by a significant size.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
OWE is defined in RFC 8110 and provides encryption and forward security
for open networks.
This is based on the requirements in the Wifi alliance document
Opportunistic_Wireless_Encryption_Specification_v1.0_0.pdf
The wifi alliance requires ieee80211w for the OWE mode.
This also makes it possible to configure the OWE transission mode which
allows it operate an open and an OWE BSSID in parallel and the client
should only show one network.
This increases the ipkg size by 5.800 Bytes.
Old: 402.541 Bytes
New: 408.341 Bytes
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This build the full openssl and wolfssl versions with SAE support which
is the main part of WPA3 PSK.
This needs elliptic curve cryptography which is only provided by these
two external cryptographic libraries and not by the internal
implementation.
The WPA3_Specification_v1.0.pdf file says that in SAE only mode
Protected Management Frames (PMF) is required, in mixed mode with
WPA2-PSK PMF should be required for clients using SAE, and optional for
clients using WPA2-PSK. The defaults are set now accordingly.
This increases the ipkg size by 8.515 Bytes.
Old: 394.026 Bytes
New: 402.541 Bytes
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This replaces the configuration files with the versions from the hostapd
project and the adaptions done by OpenWrt.
The resulting binaries should be the same.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
It's required to support devices using adjustable SoC pins for some
specific purpose (e.g. I2C, PWM, UART1).
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Update ath10k-ct to be able to drop 210-ath10k-fix-recent-bandwidth-conversion-bug.patch
as its upstream.
b9989fbd5d6e ath10k-ct: Add upstream patch to fix peer rate reporting.
ac9224344dbf ath10k-ct: Support sending custom frames with no-ack flag.
bc938bc2021e ath10k-ct: Support sending pkts with specific rate on 10.4 firmware.
Runtime tested on:
- GL-iNet GL-B1300
- Mikrotik RB912 + QCA9882
Signed-off-by: Robert Marko <robimarko@gmail.com>
[Added list of all changes from previous version + add own test device]
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Check pin count value from pin status and stop verification the pin if
the value is less then 3. This should prevent the proto-handler to
lock the SIM. If SIM is locked then the PUK is needed.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Load the json output from uqmi --get-pin-status command and evaluate the
"pin1_status" value.
The following uqmi "pin1_status" values are evaluated:
- disabled
Do not verify PIN because SIM verification is disabled on this SIM
- blocked
Stop qmi_setup because SIM is locked and a PUK is required
- not_verified
SIM is not yet verified. Do a uqmi --verify-pin1 command if a SIM is
specified
- verified:
Do not verify the PIN because this was already done before
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
QMI proto setup-handler will wait forever if SIM does not get initialized.
To fix this stop polling pin status and notify netifd. Netifd will generate
then a "ifup-failed" ACTION.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
QMI proto setup-handler will wait forever if it is unable to registrate to
the mobile network. To fix this stop polling network registration status
and notify netifd. Netifd will generate then a "ifup-failed" ACTION.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
This value will be used for now during following situations:
* Ask the sim with the uqmi --get-pin-status command.
* Wait for network registration with the uqmi --get-serving-system command.
This two commands wait forever in a while loop. Add a timeout to stop
waiting and so inform netifd.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Move uqmi std and error output on commands without using them to /dev/null.
This will remove useless outputs in the syslog.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Instead of reverting whole commit it's enough to just revert a single
line change. It seems the real problem with the regressing commit was a
bump of read chunk size. Switching back to 256 B chunks is enough to fix
the problem/regression.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Since kernel 4.14.75 commit ("netfilter: xt_cluster: add dependency on conntrack module")
a dependency is required on kmod-nf-conntrack.
It seems this was already present for kmod-ipt-clusterip
but not yet for kmod-ipt-cluster
Add it fixing a build error when including kmod-ipt-cluster:
Package kmod-ipt-cluster is missing dependencies for the following libraries:
nf_conntrack.ko
modules/netfilter.mk:665: recipe for target '/mnt/ramdisk/koen/firmware/builds/openwrt/bin/targets/cns3xxx/generic/packages/kmod-ipt-cluster_4.14.75-1_arm_mpcore_vfp.ipk' failed
make[3]: *** [/mnt/ramdisk/koen/firmware/builds/openwrt/bin/targets/cns3xxx/generic/packages/kmod-ipt-cluster_4.14.75-1_arm_mpcore_vfp.ipk] Error 1
make[3]: Leaving directory '/mnt/ramdisk/koen/firmware/builds/openwrt/package/kernel/linux'
Command exited with non-zero status 2
time: package/kernel/linux/compile#1.80#0.05#2.07
package/Makefile:107: recipe for target 'package/kernel/linux/compile' failed
make[2]: *** [package/kernel/linux/compile] Error 2
make[2]: Leaving directory '/mnt/ramdisk/koen/firmware/builds/openwrt'
package/Makefile:103: recipe for target '/mnt/ramdisk/koen/firmware/builds/openwrt/staging_dir/target-arm_mpcore+vfp_musl_eabi/stamp/.package_compile' failed
make[1]: *** [/mnt/ramdisk/koen/firmware/builds/openwrt/staging_dir/target-arm_mpcore+vfp_musl_eabi/stamp/.package_compile] Error 2
make[1]: Leaving directory '/mnt/ramdisk/koen/firmware/builds/openwrt'
/mnt/ramdisk/koen/firmware/builds/openwrt/include/toplevel.mk:216: recipe for target 'world' failed
make: *** [world] Error 2
Fixes: f983956a8b ("kernel: bump 4.14 to 4.14.75")
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
[1] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v4.14.75&id=b969656b46626a674232c0eadf92a394b89df07c
Christian Lamparter
Hans Dedecker
Koen Vandeputte
Kevin Darbyshire-Bryant
Felix Fietkau
Daniel Golle
Hauke Mehrtens
Russell Senior
Florian Eckert
Rafał Miłecki
Robert Marko
John Crispin
Rosen Penev
Magnus Kroken