Many target use a repetitive if-include scheme for their subtarget
image files, though their names are consistent with the subtarget
names.
This patch removes these redundant conditions and just uses the
variable for the include where the target setup allows it.
For sunxi, this includes a trivial rename of the subtarget image
Makefiles.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
remove at91-sdcard build command from Makefile as this is moved to
respective subtarget Makefile.
Signed-off-by: Sandeep Sheriker M <sandeep.sheriker@microchip.com>
Instead of maintaining 3 very similar subtargets merge them into one.
This does not use the Arm NEON extension any more, because the SAMA5D3
does not support NEON.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Sandeep Sheriker <sandeepsheriker.mallikarjun@microchip.com>
reorganizing at91 subtargets based on sama5 soc features and this fix
below problems.
1. able to set neon flags to sama5d2 & sama5d4 subtargets.
2. fix the make clean which removes all the subtargets in bin folder.
3. able to configure kernel specific to subtarget.
4. able to set vfpu4 flags to samad3 subtargets.
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
creating sdcard image with ext4 rootfs only and ignoring creating
other filesystem in sdcard image.
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
The current image build code has a number of race conditions and interface
contract violations in the custom image build steps:
- Build/install-zImage, solely used by at91, relies on $(PROFILE_SANITIZED)
which is not available when building with CONFIG_TARGET_MULTI_PROFILE
- Build/at91-sdcard, which may run concurrently, creates scratch files at
fixed locations and manipulates target files directly which can lead
to file corruption and other unexpected failures
Rename the install-zImage macro to at91-install-zImage and move it to the
at91 image Makefile since this target is the sole user. Also utilize "$@"
as output file name and switch the usage of $(PROFILE_SANITIZED) to
$(DEVICE_NAME) in order to fix naming under multi profile builds.
Fix the at91-sdcard macro to construct scratch file paths relative to "$@",
which is guaranteed to be unique and store the final artifact output in "$@"
as well, instead of inside $(BIN_DIR). The generic image build code takes
care of moving a build steps "$@" output to the final destination in a
concurrency-safe manner.
Finally remove the broken install-zImage from the generic image-commands
Makefile.
Fixes: d7a679a036 ("at91: Install zImage.")
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The build system took the DTB_SIZE definition from Default and not from
production-dtb under some conditions. Move the size definitions to
Default now as it is only used in production-dtb anyway.
Thanks Mathias Kresin for helping me with this.
Fixes: c2f052acae ("at91: convert boards to generic build target")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This module from Laird includes the following:
- CPU Atmel SoC ARM926EJS
- Wifi AR6003
- Bluetooth CSR8510
- RAM 64MB LPDDR
- FLASH 128MB
The flash is a dual image layout, kernel a/b, rootfs a/b, and a user
partition.
Signed-off-by: Ben Whitten <ben.whitten@gmail.com>
Instead of applying global defaults based on selected board, transition
to using a per board setting for UBIFS and UBINIZE.
Signed-off-by: Ben Whitten <ben.whitten@gmail.com>
Renaming at91 subtarget sama5d3 to sama5 and using at91-sama5d3_xplained
as a target device in sama5 subtarget.This will enable to add other
sama5d2 & sama5d4 target devices in sama5 subtraget.This will avoid
code duplication when sama5d2 & sama5d4 added as different subtarget.
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
Evaluation boards are left in component form to ease flashing
using vendor tooling and instructions. These boards also do
not include the EOF marker in the UBIFS as the bootloaders
are recent and easily upgradeable.
The end product boards use factory.bin images based on the
dts layout and include EOF markers as bootloader UBI support
is not determined.
Signed-off-by: Ben Whitten <ben.whitten@gmail.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
As the Default profile option is a legacy subtarget, the dtb for the
sama5d3_xplained board DTS is not built and image generation fails.
Signed-off-by: Ben Whitten <ben.whitten@gmail.com>
SVN-Revision: 48351
From 272f548fe8d0b811e0589e535f650f0507f6bccd Mon Sep 17 00:00:00 2001
From: Owen Kirby <osk@exegin.com>
Date: Fri, 11 Apr 2014 17:59:55 -0700
Subject: [PATCH 2/3] [at91] AT91SAM9G20-EK fixes.
While testing the 3.10 kernel update, I found that the out-of-the-box device tree for the
the AT91SAM9G20EK uses a UBIFS rootfs and stores the DTB separately from the zImage.
Signed-off-by: Owen Kirby <osk@exegin.com>
SVN-Revision: 40597
This upgrades the AT91 target to 3.8.7, and migrates to device tree.
This allows a single kernel to be built for most at91 variants which
simplifies things quite a bit. The immediate result is that all
subtargets are nuked, and any boards without dts files are no longer
supported, though the target now includes more boards than before. The
adc driver was also nuked as 3.8.7 includes a new one under the IIO
subsystem.
Signed-off-by: Adam Porter <porter.adam@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36452
Adrian Schmutzler
Sandeep Sheriker M
Hauke Mehrtens
Sandeep Sheriker Mallikarjun
Jo-Philipp Wich
Ben Whitten
John Crispin
Jo-Philipp Wich
Florian Fainelli
Gabor Juhos
Claudio Mignanti
Nicolas Thill
Felix Fietkau