This patch adds support for the TP-Link TL-WR802N-v4.
https://openwrt.org/toh/tp-link/tl-wr802n
Specification:
- MT7628N (580 MHz)
- 64 MB RAM
- 8 MB FLASH
- 2T2R 2.4 GHz
- 1x 10/100 Mbps Ethernet
- 1x LED
Flash instruction:
The only way to flash the image in TL-WR802N v4 is to use
tftp recovery mode in U-Boot:
1. Configure PC with static IP 192.168.0.225/24 and tftp server.
2. Rename "openwrt-ramips-mt76x8-tplink_tl-wr802n-v4-squashfs-tftp-recovery.bin"
to "tp_recovery.bin" and place it in tftp server directory.
3. Connect PC with the LAN port, press the reset button, power up
the router and keep button pressed for around 10 seconds, until
device starts downloading the file.
4. Router will download file from server, write it to flash and reboot.
Signed-off-by: Marcel Jost <majo@icutech.ch>
* assign pinmux groups to gpio function for LEDs/buttons
* rename flash node to be more generic in line with other device nodes
* remove useless/incorrect eeprom property from wmac node
* correct base mac address for embedded switch
Signed-off-by: Thomas Vincent-Cross <me@tvc.id.au>
* wg-quick: freebsd: allow loopback to work
FreeBSD adds a route for point-to-point destination addresses. We don't
really want to specify any destination address, but unfortunately we
have to. Before we tried to cheat by giving our own address as the
destination, but this had the unfortunate effect of preventing
loopback from working on our local ip address. We work around this with
yet another kludge: we set the destination address to 127.0.0.1. Since
127.0.0.1 is already assigned to an interface, this has the same effect
of not specifying a destination address, and therefore we accomplish the
intended behavior. Note that the bad behavior is still present in Darwin,
where such workaround does not exist.
* tools: remove unused check phony declaration
* highlighter: when subtracting char, cast to unsigned
* chacha20: name enums
* tools: fight compiler slightly harder
* tools: c_acc doesn't need to be initialized
* queueing: more reasonable allocator function convention
Usual nits.
* systemd: wg-quick should depend on nss-lookup.target
Since wg-quick(8) calls wg(8) which does hostname lookups, we should
probably only run this after we're allowed to look up hostnames.
* compat: backport ALIGN_DOWN
* noise: whiten the nanoseconds portion of the timestamp
This mitigates unrelated sidechannel attacks that think they can turn
WireGuard into a useful time oracle.
* hashtables: decouple hashtable allocations from the main device allocation
The hashtable allocations are quite large, and cause the device allocation in
the net framework to stall sometimes while it tries to find a contiguous
region that can fit the device struct. To fix the allocation stalls, decouple
the hashtable allocations from the device allocation and allocate the
hashtables with kvmalloc's implicit __GFP_NORETRY so that the allocations fall
back to vmalloc with little resistance.
* chacha20poly1305: permit unaligned strides on certain platforms
The map allocations required to fix this are mostly slower than unaligned
paths.
* noise: store clamped key instead of raw key
This causes `wg show` to now show the right thing. Useful for doing
comparisons.
* compat: ipv6_stub is sometimes null
On ancient kernels, ipv6_stub is sometimes null in cases where IPv6 has
been disabled with a command line flag or other failures.
* Makefile: don't duplicate code in install and modules-install
* Makefile: make the depmod path configurable
* queueing: net-next has changed signature of skb_probe_transport_header
A 5.1 change. This could change again, but for now it allows us to keep this
snapshot aligned with our upstream submissions.
* netlink: don't remove allowed ips for new peers
* peer: only synchronize_rcu_bh and traverse trie once when removing all peers
* allowedips: maintain per-peer list of allowedips
This is a rather big and important change that makes it much much faster to do
operations involving thousands of peers. Batch peer/allowedip addition and
clearing is several orders of magnitude faster now.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
squashfskit is a fork of the squashfs-tools.
squashfskit creates reproducible filesystems and includes
many of the distro patches.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Tested-by: Paul Spooren <mail@aparcar.org>
This is bugfix release that incorporated all of the devcrypto engine
patches currently in the tree.
The cleaning procedure in Package/Configure was not removing the
dependency files, causing linking errors during a rebuild with
different options. It was replaced by a simple make clean.
Signed-off-by: Eneas U de Queiroz <cote2004-github@yahoo.com>
omcproxy's configuration is lost on every update or installation.
Avoid it by defining the configuration file.
Signed-off-by: David Santamaría Rogado <howl.nsp@gmail.com>
After update to 5.0.1 iw-full package failed to display command list on
ipq40xx arch. Root cause was found to be LTO reordering causing
incorrect detection of command struct size in:
iw.c:552
cmd_size = labs((long)&__section_set - (long)&__section_get);
This reverts commit ef16a394d2.
Signed-off-by: Mantas Pucka <mantas@8devices.com>
The TP-Link WDR3600 shares the same machine-code in the ar71xx target,
thus expecting "tl-wdr4300" not "tl-wdr3600" in the support-list
metadata to allow non-forced sysupgrades from ar71xx to ath79.
With this, it is possible to flash a WDR4300 image on the WDR3600. It
is no problem however, as the only difference is the 5GHz WiFi chip
which has 3SS instead of 2SS. Both work with either image.
Signed-off-by: David Bauer <mail@david-bauer.net>
This adds the support-list entry the AVM FRITZ!Box 4020 expects in the
ar71xx target to allow non-forced sysupgrades from ar71xx to ath79.
Signed-off-by: David Bauer <mail@david-bauer.net>
remove USB as this is no LED but power control
rename WiFi LED with correct color red (like in stock firmware)
set middle LED to be used for LAN link/activity
Signed-off-by: Andreas Ziegler <dev@andreas-ziegler.de>
If no mcast_rate is set for the wifi-iface then there is no rate_idx (0)
set for the bss. This can break for example 5GHz meshpoint interfaces
because 0 maps to a CCK rate (11Mbit/s).
It must also be avoided that the ath10k-ct internal state for the rates is
not synced with the mac80211 rates state. Otherwise, the user specified
rate (e.g. a wifi-iface mcast_rate for a meshpoint interface) will only be
set on startup. And a short while after that, ath10k-ct specific code in
ath10k_check_apply_special_rates is missing a valid rate in its own
structures and is then recalculating a new default rate. This default rate
is in most situations not the requested rate.
Fixes: 4df3c71cd4 ("ath10k-ct: Update to 2018-12-11 and use version based on 4.19")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
If no mcast_rate is set for the wifi-iface then there is no rate_idx (0)
set for the bss. This breaks for example 5GHz meshpoint interfaces because
0 maps to a CCK rate (11Mbit/s).
Fixes: db90c243a0 ("mac80211: update to version based on 4.19-rc4")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
This should fix the WDS / 4addr mode with ath10k and probably other
devices.
This patch was found here: https://patchwork.kernel.org/patch/10692383/
Fixes: d9eefa7a70 ("mac80211: rebase ontop of v4.18.5")
Reported-by: Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Fix crash due to passing invalid r2x00dev->eeprom_file pointer to
release_firmware(). Since we copy eeprom data with EEPROM_SIZE
in rt2800_read_eeprom() we can use eeprom_file->size as marker
if the file was crated by request_firmware().
Acked-by: Kristian Evensen <kristian.evensen@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Use 'dtc' from kernel sources instead of relying on host tool.
Fixes: bf4630e5ad ("build: add helpers for generating QSDK sysupgrade compatible images")
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
ALFA Network AP120C-AC is a dual-band ceiling AP, based on Qualcomm
IPQ4018 + QCA8075 platform.
Specification:
- Qualcomm IPQ4018 (717 MHz)
- 256 MB of RAM (DDR3)
- 16 MB (SPI NOR) + 128 MB (SPI NAND) of flash
- 2x Gbps Ethernet, with 802.3af PoE support in one port
- 2T2R 2.4/5 GHz (IPQ4018), with ext. FEMs (QFE1952, QFE1922)
- 3x U.FL connectors
- 1x 1.8 dBi (Bluetooth) and 2x 3/5 dBi dual-band (Wi-Fi) antennas
- Atmel/Microchip AT97SC3205T TPM module (I2C bus)
- TI CC2540 Bluetooth LE module (USB 2.0 bus)
- 4x LED (all driven by GPIO)
- 1x button (reset)
- 1x USB 2.0 (optional, not installed in indoor version)
- DC jack for main power input (12 V)
- UART header available on PCB (2.0 mm pitch)
Flash instruction:
1. This board uses dual-image feature (128 MB NAND is divided into two
64 MB partitions: 'rootfs1' and 'rootfs2').
2. Before update, make sure your device is running firmware no older
than v1.1 (previous versions have incompatible U-Boot).
3. Use 'factory' image in vendor GUI or for sysupgrade tool, without
preserving settings.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Without a proper SPI NAND support (SPI NAND framework is available in
kernel >= 4.19) the only way to make such flash working is to include
it in raw/parallel NAND subsystem support and combine with mt29f staging
driver. Obviously, this approach isn't going to be accepted by upstream
(similar support for Winbond W25N01GV was rejected).
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Qualcomm SDK (QSDK) sysupgrade compatible images for IPQ40xx, IPQ806x
and IPQ807x use FIT format together with 'dumpimage' tool from U-Boot
for verifying and extracting them. Based on 'images' sections names,
corresponding mtd partitions are flashed. For example, in case of
NOR-only boards, below mapping is used (section name -> mtd name):
hlos* -> 0:HLOS
rootfs* -> rootfs
And for boards with NAND (kernel inside UBI):
ubi* -> rootfs
Above mappings come from unmodified QSDK sources and might be wrong for
boards running custom or modified QSDK-based firmware. Some of vendors
adjust them to meet their modified mtd layout or features like recovery
or dual-image support.
This adds simple script 'mkits-qsdk-ipq-image.sh' (based on 'mkits.sh')
for generating FIT images tree source files, compatible with the QSDK
sysupgrade format. Resulting images can be used for initial (factory ->
OpenWrt) installation and would work both in CLI and GUI.
The script is universal in a way it allows to include as many sections
as needed. To make use of it, two generic/basic build recipes for NOR
and NAND based boards are also included in 'image-commands.mk':
Build/qsdk-ipq-factory-nand
Build/qsdk-ipq-factory-nor
Example usage for board with UBI in NAND:
IMAGE/nand-factory.bin := append-ubi | qsdk-ipq-factory-nand
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
The addition of kmod-input-touchscreen-ads7846 enabled
INPUT_TOUCHSCREEN, which exposes several other symbols on various
targets. Add those symbols to the generic kernel configs to fix build.
Fixes: 77a54bbf13 ("kernel: add kmod-input-touchscreen-ads7846")
Reported-by: Hannu Nyman <hannu.nyman@iki.fi>
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
On targets that don't have input support enabled in the kernel config,
building kmod-input-touchscreen-ads7846 fails due to a missing
dependency on kmod-input-core. Add the dependency to fix this.
Fixes: 77a54bbf13 ("kernel: add kmod-input-touchscreen-ads7846")
Reported-by: Hannu Nyman <hannu.nyman@iki.fi>
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
max_ttl - limit the ttl in the dns answer if greater as $max_ttl
min_cache_ttl - force caching of dns answers even the ttl in the answer
is lower than the $min_cache_ttl
max_cache_ttl - cache only dns answer for $max_cache_ttl.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
This module adds support for ADS7846 based touchscreens used in devices
like the WaveShare 3.5" and 4" LCD displays designed for Raspberry Pi.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
This module adds support for the ILI9486 LCD controller used in devices
like the Waveshare 3.5" and 4" LCD displays designed for Raspberry Pi.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
This module adds support for small TFT LCD display modules. While this
module also exists in the 4.9 kernel, we are not going to support this
kernel in the next major release, so don't make it available for 4.9.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
The kernel modules that provide support for framebuffers in system RAM
are currently included in the kmod-drm-imx package. Move them to a
separate package, so that other modules can depend on them.
Increase the autoload order of the drm-imx* packages to load the modules
after loading the fb modules they depend on.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
This makes it clear that localuse when explicitly specified in the
config will have its final say on whether or not the initscript should
touch /etc/resolv.conf, no matter whatever the result of previous
guesswork would be
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
This can be used to set machine options like highmem=off for running old
armvirt/32 kernel lacking LPAE support with QEMU version 3.0 or later
[1] Armv7 guest fails to boot with qemu-3.0.0-1,
https://bugzilla.redhat.com/show_bug.cgi?id=1633328#c5
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Marcel Jost
Thomas Vincent-Cross
Jason A. Donenfeld
Alexander Couzens
Eneas U de Queiroz
Hans Dedecker
David Santamaría Rogado
Mantas Pucka
Hauke Mehrtens
Syrone Wong
Daniel Engberg
Matt Merhar
Aleksander Jan Bajkowski
David Bauer
Andreas Ziegler
Sven Eckelmann
Stanislaw Gruszka
Felix Fietkau
Piotr Dymacz
Koen Vandeputte
Stijn Tintel
Yousong Zhou