This reverts commit 5555545494.
The target supports both NEON and VFPv4, but for this to work properly,
a few more changes are needed:
- enable NEON support in the kernel config
- add the fpu feature flag to the makefile
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The stats update needs to protect against being interrupted by a tasklet
The u64 stats seqlock needs to be initialized
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The pins are used as (LED) GPIOs and can't be used at the same time as
hardware controlled ephy (LED) pins.
Fixes: FS#1500
Signed-off-by: Mathias Kresin <dev@kresin.me>
In the new USB phy driver, it checks the compatible string before
attempting to iomap its mem resource and do the extra PHY init
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The MX60's uboot disables all the PHYs before starting linux.
This causes the PHY/switch detection code to malfunction
almost all of the time. To get around this, set a compatible
flag to force PHYID.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
Don't select the firmware with the board file, it prevents an easy use
of the -ct ath10k firmware. Select the firmware within the default
packages instead.
Remove the per device selection of the firmware now that it the
firmware is selected by default.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Specifications:
SOC: Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core
RAM: 256 MB Winbond W632GU6KB12J
FLASH: 16 MiB Macronix MX25L12805D
ETH: Qualcomm QCA8072
WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11b/g/n/ac 2x2
WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11n/ac
1x1 (EX6100)
2x2 (EX6150)
INPUT: Power, WPS, reset button
AP / Range-extender toggle
LED: Power, Router, Extender (dual), WPS, Left-/Right-arrow
SERIAL: Header next to QCA8072 chip.
VCC, TX, RX, GND (Square hole is VCC)
WARNING: The serial port needs a TTL/RS-232 v3.3 level converter!
The Serial setting is 115200-8-N-1.
Tested and working:
- Ethernet
- 2.4 GHz WiFi (Correct MAC-address)
- 5 GHz WiFi (Correct MAC-address)
- Factory installation from WebIF
- Factory installation from tftp
- OpenWRT sysupgrade (Preserving and non-preserving)
- LEDs
- Buttons
Not Working:
- AP/Extender toggle-switch
Untested:
- Support on EX6100v2. They share the same GPL-Code and vendor-images.
The 6100v2 seems to lack one 5GHz stream and differs in the 5GHz
board-blob. I only own a EX6150v2, therefore i am only able to verify
functionality on this device.
Install via Web-Interface:
Upload the factory image to the device to the Netgear Web-Interface.
The device might asks you to confirm the update a second time due to
detecting the OpenWRT firmware as older. The device will automatically
reboot after the image is written to flash.
Install via TFTP:
Connect to the devices serial. Hit Enter-Key in bootloader to stop
autobooting. Command "fw_recovery" will start a tftp server, waiting for
a DNI image to be pushed.
Assign your computer the IP-address 192.168.1.10/24. Push image with
tftp -4 -v -m binary 192.168.1.1 -c put <OPENWRT_FACTORY>
Device will erase factory-partition first, then writes the pushed image
to flash and reboots.
Parts of this commit are based on Thomas Hebb's work on the
openwrt-devel mailinglist.
See https://lists.openwrt.org/pipermail/openwrt-devel/2018-January/043418.html
Signed-off-by: David Bauer <mail@david-bauer.net>
This patch adds support for 8devices Jalapeno.
Specification:
QCA IPQ4018, Quad core ARM v7 Cortex A7 717MHz
256 MB of DDR3 RAM
8 MB of SPI NOR flash
128 MB of Winbond SPI NAND flash
WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2
requires special BDF in QCA4019/hw1.0/board-2.bin with:
bus=ahb,bmi-chip-id=0,bmi-board-id=16,variant=8devices-Jalapeno
WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2
requires special BDF in QCA4019/hw1.0/board-2.bin with:
bus=ahb,bmi-chip-id=0,bmi-board-id=17,variant=8devices-Jalapeno
ETH: Qualcomm Atheros QCA8072 Gigabit Switch (1 x LAN, 1 x WAN)
phy@mdio3:
Label: eth0
gmac0
phy@mdio4:
Label: eth1
gmac1
Installation instructions:
Since boards ship with old version of LEDE installation is simple.
Just use sysupgrade -n -F sysupgrade.bin
Syuspgrade needs to be forced since OpenWRT uses DT detection in recent
releases.
If you get error that FIT configuration is not found during boot it is
due to older U-boot used on your board.
That is because 8devices used custom FIT configuration partition name
as they internally had v1 and v2 boards.
Only v2 boards are sold so now they are shipping boards with never
U-boot using generic config@1 FIT partition name.
Also for old uboot it is possible to force loading config@1 by changing
uboot environment:
setenv boot5 'bootm 0x84000000#config@1’
saveenv
Signed-off-by: Robert Marko <robimarko@gmail.com>
This is important fix for flash parsing in some corner cases. In case
of TRX subpartition with rootfs being aligned to the flash block size it
was incorrectly registered twice. Detecting & registering it as a
standalone partition was resulting in an incorrect "firmware" partition
size and possibly broken sysupgrade.
It wasn't noticed before because "rootfs" alignment depends on a kernel
size. It can happen though - depending on the configuration and the
kernel size.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Previously, tplink_pharos_check_image() would accept any image with ELF
magic and only non-printable data in the support-list, as in this case the
while-read loop would not run at all. Add the new support-list offset and
ensure an image is only accepted when the model string is actually found.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Some Airmax devices can establish a Gigabit link even though the MAC only
supports 10/100 MBit/s, leading to broken connectivity. Prevent this from
happening by limiting the speed to 100MBit/s.
Fixes: FS#296
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
This solution is more upstream compatible as it only requires specifying
of_match_table in the parser code and doesn't depend on linux,part-probe
which is solution made generic by a LEDE downstream patch that can't be
upstreamed.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Acked-by: John Crispin <john@phrozen.org>
These patches were finally accepted and are already present in the
Linus's tree. This should be good enough to make is "backport" material.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
With kernel 4.14 the OpenWrt specific module name collides with the
upstream added module for Mediatek ARM Socs.
During addition of preliminary support for kernel 4.14, the config
symbol used by the out of tree driver was already renamed but the ramips
kernel package wasn't updated.
Fix the build error by updating the config and kernel module name for
the kernel package.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The Zorlik ZL5900V2 is an unbranded clone of HAME MPR-A1/2. It is
marketed as "3G Wi-Fi Router". Only the PCB has the model name
"ZL5900V2" printed on it.
Specifications:
- Ralink RT5350F (360 MHz)
- 32 MB RAM
- 8 MB Flash
- 802.11bgn 1T1R
- 1x 10/100 Mbps Ethernet
- 1x USB 2.0 (Type-A)
- 5200 mAh battery
The ramdisk image (not the squashfs sysupgrade image) can be flashed
through the web interface (named "GoAhead") of the factory firmware.
However, as the factory firmware does not cleanly unmount the rootfs
before flashing, the device may hang instead of rebooting after
successful write. Power cycling the device gets you in OpenWrt where
the squashfs image may be flashed through normal sysupgrade procedure.
Signed-off-by: Vianney le Clément de Saint-Marcq <code@quartic.eu>
YouHua tech WR1200JS is an AC1200 router with 5 1Gb ports (4 Lan, 1 Wan)
and 1 USB 2.0 port.
Devices is base on MediaTek MT7621AT + MT7603E + MT7612E.
Specification:
- MT7612AT (880 MHz)
- 128 MB of RAM
- 16 MB of FLASH (SPI NOR)
- 5x 10/100/1000 Mbps Ethernet
- 2T2R 2.4 GHz (MT7603E)
- 2T2R 5 GHz (MT7612E)
- 1x USB 2.0
- 10x LED (Power 2G 5G WPS Internet LAN4-1 USB)
- 3x button (reset wifi wps)
- DC jack for main power input (12V)
Installation:
1.) Press reset key 5 sec and restore the factory default
2.) Login webUI and change username to root and set a
new password
3.) Visit http://192.168.2.254/adm/telnetd.shtml and
turn on the telnet service
4.) Copy openwrt-ramips-mt7621-youhua_wr1200js-initramfs-kernel.bin
to a usb pan
5.) Plug the usb pan to the router, telnet to the router
and login by root
6.) cd /media/sda1 and check the initramfs file is there
7.) exec command:
mtd_write write openwrt-ramips-mt7621-youhua_wr1200js-initramfs-kernel.bin Kernel
8.) reboot and visit 192.168.1.1
Signed-off-by: Zheng Qian <sotux82@gmail.com>
The previous fw version require the replacement of the stock bootloader
with u-boot. This prevent an easy stock restore of the original fw.
Now a proper fw util has been developed to manage the stock jboot
bootloader. Therefore make sense have a fw image for the stock
bootloader.
The old fw configuration (u-boot) is not compatible with the new one
and will not be supported anymore.
So at the end 2 image can be generated:
1) factory image with jboot bootloader
openwrt-ramips-rt305x-dwr-512-b-squashfs-factory.bin
2) sysupgrade image with jboot bootloader
openwrt-ramips-rt305x-dwr-512-b-squashfs-sysupgrade.bin
Signed-off-by: Giuseppe Lippolis <giu.lippolis@gmail.com>
The Ralink USB PHY driver merged into mainline has a slightly different
device tree binding than the patch that was used with linux 4.9.
The new driver requires a `ralink,sysctl` node pointing to the `syscon`
node.
This patch also sets `#phy-cells` to 0, as recommended by the mainline
documentation [1].
[1] Documentation/devicetree/bindings/phy/ralink-usb-phy.txt
Signed-off-by: Vianney le Clément de Saint-Marcq <code@quartic.eu>
TP-Link Archer C60 v2 is a dual-band AC1350 router, based on
Qualcomm/Atheros QCA9561 + QCA9886.
Specification:
- 775/650/258 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 2T2R 5 GHz
- 5x 10/100 Mbps Ethernet
- 7x LED, 2x button
- UART header on PCB
Flash instruction (web):
Download lede-ar71xx-generic-archer-c60-v2-squashfs-factory.bin and use
OEM System Tools - Firmware Upgrade site.
Flash instruction (recovery):
1. Set PC to fixed IP address 192.168.0.66
2. Download lede-ar71xx-generic-archer-c60-v2-squashfs-factory.bin and
rename it to tp_recovery.bin
3. Start a tftp server with the file tp_recovery.bin in its root
directory
4. Turn off the router
5. Press and hold reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time the firmware should
be transferred from the tftp server
8. Wait ~30 second to complete recovery
Flash instruction (under U-Boot, using UART):
tftp 0x81000000 lede-ar71xx-...-sysupgrade.bin
erase 0x9f030000 +$filesize
cp.b $fileaddr 0x9f030000 $filesize
reset
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
Add support for TL-WR940N v6 board. It is pretty much the same as v5
except they only left WAN LED and removed other ones.
Installation: flash factory image through WEB UI or use TFTP.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Rework (again) platform support for dual-role chipidea USB controller:
- include support for QCA9531
- use correct EHCI block size
- drop ar933x_usb_setup_ctrl_config() function
- simplify code after previous "register chipidea only in device mode"
change (fa22714181)
Reworked patch was tested on devices with below QCA WiSOCs (signal/GPIO
name with required bootstrap state for USB bus 0 in device mode):
- AR9331 (GPIO13 pull-down)
- AR9342 (RGMII_TXD1/ETXD1 pull-up)
- AR9344 (GPIO20 pull-up)
- QCA9531 (GPIO13 pull-up)
- QCA9558 (GPIO13 pull-up)
The only way to select device mode for bus 0 is to change SOC bootstrap
configuration which is sampled only once, at hard reset. Likely, other
models, like QCA9556 or AR9341, should also support dual-role USB mode
but they were not tested.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Supports IPv4 flow offloading on MT7621 for Routing, SNAT and DNAT
Supported are regular ethernet->ethernet connections, including one
802.1q VLAN and/or PPPoE encapsulation
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
of_dma_configure() sets a default ->dma_mask of
DMA_BIT_MASK(32), claiming devices can DMA from
the full 32bit address space.
The mtk-mmc driver does not support access to
highmem pages, so it is really limited to the
bottom 512M (actually 448M due to 64M of IO space).
Setting ->dma_mask to NULL causes mmc_setup_queue()
to fall-back to using BLK_BOUNCE_HIGH to tell the
block layer to use a bounce-buffer for any highmem
pages requiring IO.
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
- avoid using garbage stack values as dst pointer if lookup fails
- provide the source address for ipv6 dst lookup
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Our .dts files only have one device defined and this is unlikely to
change, so statically initialize host->id to 0.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This commit adds correct model detection for UniFi
AC-Mesh. Previously said device was incorrectly detected
as UniFi AC-Lite.
The Information about the device is stored at 0xC in the EEPROM
partition. It corresponds to the sysid in /etc/board.info of the
Ubiquiti stock firmware.
Signed-off-by: David Bauer <mail@david-bauer.net>
D-Link DAP-1330 rev. A1 is a wall-plug N300 Wi-Fi range extender,
based on Qualcomm/Atheros QCA9533 v2.
Short specification:
- 650/393/216 MHz (CPU/DDR/AHB)
- 1x 10/100 Mbps Ethernet
- 64 MB of RAM (DDR1)
- 8 MB of FLASH
- 2T2R 2.4 GHz
- 2x external antennas
- 6x LED (2 are bi-color), 2x button
- 4 pin on pcb (looking from eth port and from left to right tx,rx,gnd,vcc)
Flash instruction: use "factory" image directly in vendor GUI.
This device has a recovery system that assign the ip addr of env
variable "serverip" via dhcp to a pc, and the "ipaddr" value to itself.
The recovery it's triggered by a not bootable firmware,
or pressing the reset button during the bootloader startup (first 30 seconds).
The recovery uses a http page to restore the firmware, and it's checking
the firmware image header, so use the "factory" image to
restore or the original firmware.
You can access vendor firmware over serial using:
- login: root
- password: linuxrocks
Image was tested only in EU version of the device, but should work
also with the same device version sold in other countries.
Signed-off-by: Nicolò Veronese <nicveronese@gmail.com>
It was wrong from the beginning and the trigger for the wan led was
never set due to the typo.
Signed-off-by: Reto Schneider <code@reto-schneider.ch>
[add commit message]
Signed-off-by: Mathias Kresin <dev@kresin.me>
We need to reset the GPHYs on reboot as well. Otherwise the bootloader
might have issues to reset/find the GPHYs.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Felix Fietkau
Mathias Kresin
Stijn Tintel
Christian Lamparter
David Bauer
Robert Marko
Rafał Miłecki
Lucian Cristian
Matthias Schiffer
Vianney le Clément de Saint-Marcq
Zheng Qian
Giuseppe Lippolis
Henryk Heisig
Piotr Dymacz
Peng Zhang
John Crispin
NeilBrown
Nicolò Veronese
Reto Schneider