Add vendors in device names and also rename few device names, for easier
identyfying potential firmware to flash. The vendor and device string is
mainly derived from model/compatipble string in dts from particular
device, but since not all devices are well described, some of the renames
follow marketing names.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
All of arm64 devices have part of variables repeatedly defined. Stack
them to common define, and reference it in each device recipe.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Since most of devices using SD card image to boot, use ext4 as boot
files system we can drop fat fs related packages. Also move packages
which are added repeatedly across subtargets to their default packages,
with droping the ones that are enabled in target kernel configugation.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Add initial support for cortex-a72 based Armada DB-88F8040-Modular and
DB-88F7040-Modular development boards.
DB-88F8040-Modular specifications:
- Quad-core ARMv8 Cortex A72 CPU (up to 2 GHz)
- DDR4 DIMM - 64 bits + ECC
- 2 x 128 Mb SPI NOR flash memory
- 2 x 1G Ethernet port via RGMII (RJ45)
- 2 x SD card ports (4 bit port on CP, 8 bit port on AP)
- 2 SERDES modules with the following interfaces each:
- 2 x SATA Rev 3.0 port (Port1 via SERDES module CON4 (active port), Port0
via SERDES Module CON2 or CON1 (optional port))
- 3 x PCI Express (PCIe) Gen 3.0 (Port2 via SERDES module CON5 (active port),
Port1 via SERDES module CON7 (optional port), Port0 via SERDES module CON6
(optional port))
- 2 x USB3 (USB 2.0 backward compatible) host (via SERDES module CON9 and
CON10)
- 1 x 10G port over SFP+ connector (via SERDES module CON8)
- 1 x MCI interface by two over USB Type C connector
- 4 x serial COM port driven by the 88F8040 UART interface and converted to
USB via FTDI IC
- I2C Master Interface
- CP I2C 2x EEPROM @ Address 0x50 and 0x57
- 1 x I/O Expander @ Address 0x21
- Sample at Reset (SatR) memory device @ Address 0x4C and 0x4E
- I2C Slave Interface (via SERDES module) - Connection to each device on the
board via an I2C multiplexer
- JTAG interface for CPU emulator
- Board dimensions: 270 mm x 240 mm (main + SERDES module)
- SERDES Module Dimensions: 70 mm x 105 mm
DB-88F7040-Modular specifications:
- Quad-core ARMv8 Cortex A72 CPU
- CPU core operating speed of up to 1.6 GHz for Dual Core, 1.4 GHz for Quad
Core
- DDR4 - 32 bit + ECC on Module - SLM1366-V1 (DB-DDR4-40B-MODULE) 4 GByte
32-bit
- 1 x 128Mb SPI NOR flash memory
- 2 x 1G Ethernet port: 1 over RGMII (RJ45) and 1 over SGMII
- SD card 4 bits port on AP
- eMMc Module on CP
- 1 SERDES Modules with the following interfaces each:
- 1 x SATA Rev 3.0 port (via SERDES module CON4)
- 1 x PCI Express (PCIe) Gen 3.0 (via SERDES module CON5)
- 2 x USB 3.0 (USB 2.0 backward compatible) host (via SERDES module CON9 and
CON10)
- 1 x 10G port over SFP+ connector (via SERDES module CON8)
- 2 x MCi interface by one over USB Type C connector
- 4 x Serial COM port driven by the 88F7040 UA
- RT interface and converted to USB via FTDI IC
- I2C Master Interface
- 2 x EEPROM at address 0x57 and 0x50 in AP and 2 x EEPROM at address 0x57
and 0x50 in CP
- 1 x I/O Expander at address 0x21
- Sample at Reset (SatR) memory device at address 0x4C and 0x4E
- I2C Slave Interface (via SERDES module) - Connection to each device on the
board via an I2C multiplexer
- JTAG interface for CPU emulator
- Board dimensions - 270 mm x 240 mm (main + SERDES module)
- SERDES Module Dimensions - 70 mm x 105 mm
Booting from USB flash drive (dd sdcard image to the flash drive):
1. reset U-Boot environment:
env default -a
saveenv
2. prepare U-Boot manually (make sure to set correct dtb file name):
setenv bootargs_root 'root=/dev/sda2 rw rootdelay=2 ip=dhcp'
setenv fdtfile armada-7040-db.dtb
setenv image_name Image
setenv bootcmd 'usb start; ext4load usb 0:1 $kernel_addr $image_name; ext4load usb 0:1 $fdt_addr $fdtfile; setenv bootargs $console $mtdparts $bootargs_root; booti $kernel_addr - $fdt_addr'
saveenv
boot
Signed-off-by: Damir Samardzic <damir.samardzic@sartura.hr>
Add initial support for Marvell MACCHIATObin, cortex-a72 based Marvell
ARMADA 8040 Community board. Comes in two forms: Single Shot and Double
Shot.
Specifications:
- Quad core Cortex-A72 (up to 2GHz)
- DDR4 DIMM slot with optional ECC and single/dual chip select support
- Dual 10GbE (1/2.5/10GbE) via copper or SFP
2.5GbE (1/2.5GbE) via SFP
1GbE via copper
- SPI Flash
- 3 X SATA 3.0 connectors
- MicroSD connector
- eMMC
- PCI x4 3.0 slot
- USB 2.0 Headers (Internal)
- USB 3.0 connector
- Console port (UART) over microUSB connector
- 20-pin Connector for CPU JTAG debugger
- 2 X UART Headers
- 12V input via DC Jack
- ATX type power connector
- Form Factor: Mini-ITX (170 mm x 170 mm)
More details at http://macchiatobin.net
Booting from micro SD card:
1. reset U-Boot environment:
env default -a
saveenv
2. prepare U-Boot with boot script:
setenv bootcmd "load mmc 1:1 0x4d00000 boot.scr; source 0x4d00000"
saveenv
or manually:
setenv fdt_name armada-8040-mcbin.dtb
setenv image_name Image
setenv bootcmd 'mmc dev 1; ext4load mmc 1:1 $kernel_addr $image_name;ext4load mmc 1:1 $fdt_addr $fdt_name;setenv bootargs $console root=/dev/mmcblk1p2 rw rootwait; booti $kernel_addr - $fdt_addr'
saveenv
Signed-off-by: Damir Samardzic <damir.samardzic@sartura.hr>
Tomasz Maciej Nowak
Hauke Mehrtens
Damir Samardzic