This applies several style adjustments that have been requested in
recent reviews to older DTS files. Despite making the code base more
consistent, this will also help to reduce review time when DTSes
are copy/pasted.
Applied changes:
- Rename gpio-keys/gpio-leds to keys/leds
- Remove node labels that are not used
- Use label property for partitions
- Prefix led node labels with "led_"
- Remove redundant includes
- Harmonize new lines after status property
- Several smaller style fixes
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This addresses several issues in the DTS file:
- add diag LED support
- remove unused node names
- fix whitespace issues
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This is the result of grepping/searching for several common
whitespace issues like double empty lines, leading spaces, etc.
This patch fixes them for the ath79 target.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This patch adds the label MAC address for several devices in
ath79.
Some devices require setting the MAC address in 02_network:
For the following devices, the netif device can be linked in
device tree, but the MAC address cannot be read:
- alfa-network,ap121f
- avm,fritz300e
- ubnt-xm devices
For the following devices, label MAC address is tied to lan or
wan, so no node to link to exists in device tree:
- adtran,bsap1800-v2
- adtran,bsap1840
- dlink,dir-842-c1/-c2/-c3
- engenius,ecb1750
- iodata,etg3-r
- iodata,wn-ac1167dgr
- iodata,wn-ac1600dgr
- iodata,wn-ac1600dgr2
- iodata,wn-ag300dgr
- nec,wg800hp
- nec,wg1200cr
- trendnet,tew-823dru
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
TP-Link Archer D50 v1 is a dual-band AC1200 router + modem.
The router section is based on Qualcomm/Atheros QCA9531 + QCA9882.
The "DSL" section is based on BCM6318 but it's currently not supported.
Internally eth0 is connected to the Broadcom CPU.
Router section - Specification:
CPU: QCA9531 650/600/200 MHz (CPU/DDR/AHB)
RAM: 64 MB (DDR2)
Flash: 8 MB (SPI NOR)
Wifi 2.4GHz: QCA9531 2T2R
Wifi 5GHz: QCA9982 2T2R
4x 10/100 Mbps Ethernet
8x LED, 3x button
UART header on PCB
Known issues:
DSL not working (eth0) (WIP)
UART connection
---------------
J2 HEADER (Qualcomm CPU)
. TX
. RX
. GND
O VCC
J16 HEADER (Broadcom CPU)
O VCC
. GND
. RX
. TX
The following instructions require a connection to the J2 UART header.
Flash instruction under U-Boot, using UART
------------------------------------------
1. Press any key to stop autobooting and obtain U-Boot CLI access.
2. Setup ip addresses for U-Boot and your tftp server.
3. Issue below commands:
tftpboot 0x81000000 openwrt-ath79-generic-tplink_archer-d50-v1-squashfs-sysupgrade.bin
erase 0x9f020000 +$filesize
cp.b 0x81000000 0x9f020000 $filesize
reset
Initramfs instruction under U-Boot for testing, using UART
----------------------------------------------------------
1. Press any key to stop autobooting and obtain U-Boot CLI access.
2. Setup ip addresses for U-Boot and your tftp server.
3. Issue below commands:
tftpboot 0x81000000 openwrt-ath79-generic-tplink_archer-d50-v1-initramfs-kernel.bin
bootm 0x81000000
Restore the original firmware
-----------------------------
0. Backup every partition using the OpenWrt web interface
1. Download the OEM firmware from the TP-Link website
2. Extract the bin file in a folder (eg. Archer_D50v1_0.8.0_1.3_up_boot(170223)_full_2017-02-24_09.37.45.bin)
3. Remove the U-Boot and the Broadcom image part from the file.
Issue the following command:
dd if="Archer_D50v1_0.8.0_1.3_up_boot(170223)_full_2017-02-24_09.37.45.bin" of="Archer_D50v1_0.8.0_1.3_up_boot(170223)_full_2017-02-24_09.37.45.bin.mod" skip=257 bs=512 count=15616
4. Double check the .mod file size. It must be 7995392 bytes.
5. Flash it using the OpenWrt web interface. Force the update if needed.
WARNING: Remember to NOT keep settings.
5b. (Alternative to 5.) Flash it using the U-Boot and UART connection.
Issue below commands in the U-Boot:
tftpboot 0x81000000 Archer_D50v1_0.8.0_1.3_up_boot(170223)_full_2017-02-24_09.37.45.bin.mod
erase 0x9f020000 +$filesize
cp.b 0x81000000 0x9f020000 $filesize
reset
Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [removed
default-state = "off", it's already the default, added pcie node,
fixed typo]
Adrian Schmutzler
Davide Fioravanti