This reverts commit 9e467a764b.
The Raspberry Pi firmware recently switched to building from the common
firmware branch. This introduces changes in the core clock handling,
causing various issues.
E.g. enable_uart=1 no longer fixes the core clock frequency to 250MHz.
When the disable-bt DT overlay is not loaded, the core clock frequency
is increased to 400MHz. As a result, the UART baud rate is no longer
correct, and this causes garbled serial console, or communication
problems with HATs that use the UART.
As a workaround, the core clock could be fixed to 250MHz by adding
'core_freq=250' in /boot/config.txt, but as there appear to be other
issues than just the UART being broken, the safer bet is to revert the
firmware for now.
Upstream bug: https://github.com/raspberrypi/firmware/issues/1376
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: Álvaro Fernández Rojas <noltari@gmail.com>
Due to a typo, /boot is not properly unmounted after copying the backup
file to it. Fix the typo to solve this.
Fixes: 246916ddf4 ("brcm2708: use x86's upgrade scripts for all rpi targets")
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
As reported in https://github.com/openwrt/packages/issues/12072, the
imagebuilder fails due to a dependency resolution error when the userspace
packages are built using a target that has a different kernel version than
that which is being run. To resolve this, add a virtual kernel package with
the conditional dependency currently used in sqm-scripts. The idea is to
move the sqm-scripts dependency to this virtual package, which hopefully
should be consistent with the actual kernel module being built.
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
While the other fq-based qdiscs take advantage of skb->hash and doesn't
recompute it if it is already set, sch_cake does not.
This was a deliberate choice because sch_cake hashes various parts of the
packet header to support its advanced flow isolation modes. However,
foregoing the use of skb->hash entirely loses a few important benefits:
- When skb->hash is set by hardware, a few CPU cycles can be saved by not
hashing again in software.
- Tunnel encapsulations will generally preserve the value of skb->hash from
before the encapsulation, which allows flow-based qdiscs to distinguish
between flows even though the outer packet header no longer has flow
information.
It turns out that we can preserve these desirable properties in many cases,
while still supporting the advanced flow isolation properties of sch_cake.
This patch does so by reusing the skb->hash value as the flow_hash part of
the hashing procedure in cake_hash() only in the following conditions:
- If the skb->hash is marked as covering the flow headers (skb->l4_hash is
set)
AND
- NAT header rewriting is either disabled, or did not change any values
used for hashing. The latter is important to match local-origin packets
such as those of a tunnel endpoint.
The immediate motivation for fixing this was the recent patch to WireGuard
to preserve the skb->hash on encapsulation. As such, this is also what I
tested against; with this patch, added latency under load for competing
flows drops from ~8 ms to sub-1ms on an RRUL test over a WireGuard tunnel
going through a virtual link shaped to 1Gbps using sch_cake. This matches
the results we saw with a similar setup using sch_fq_codel when testing the
WireGuard patch.
Fixes: 046f6fd5daef ("sched: Add Common Applications Kept Enhanced (cake) qdisc")
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
A direct upgrade from previous swconfig version with
incompatible settings to DSA will break the internet.
Remove SUPPORTED_DEVICES so users cannot upgrade directly.
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
[rebase after Linksys rename, adjust title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The Linksys devices in mvebu target feature a mixed naming,
where parts are based on the official product name (device
node, image; e.g. WRT3200ACM) and parts are based on the
internal code name (DTS file name, compatible, LED labels;
e.g. rango). This inconsistent naming has been perceived
as quite confusing.
A recent attempt by Paul Spooren to harmonize this naming
in kernel has been declined there. However, for us it still
makes sense to apply at least a part of these changes
locally.
Primarily, this patch changes the compatible in DTS and thus
the board name used in various scripts to have them in line
with the device, model and image names. Due to the recent
switch from swconfig to DSA, this allows us to drop
SUPPORTED_DEVICES and thus prevent seamless upgrade between
these incompatible setups.
However, this does not include the LED label rename from
Paul's initial patch: I don't think it's worth keeping the
enormous diff locally for this case, as we can implement
this much easier in 01_leds if we have to live with the
inconsistency anyway.
Signed-off-by: Paul Spooren <mail@aparcar.org>
[rebase, extend to all devices, drop DT LED changes]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
When a client moves from a DSA user port to a software port in a bridge,
it cannot reach any other clients that connected to the DSA user ports.
That is because SA learning on the CPU port is disabled, so the switch
ignores the client's frames from the CPU port and still thinks it is at
the user port.
Fix it by enabling SA learning on the CPU port.
To prevent the switch from learning from flooding frames from the CPU
port, set skb->offload_fwd_mark to 1 for unicast and broadcast frames,
and let the switch flood them instead of trapping to the CPU port.
Multicast frames still need to be trapped to the CPU port for snooping,
so set the SA_DIS bit of the MTK tag to 1 when transmitting those frames
to disable SA learning.
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
Currently enabling VLAN filtering blocks all traffic in the bridge
immediately. That is because DSA ignores all VLAN setup when VLAN
filtering is disabled, and when it is enabled, there is no VLAN entry
in the VLAN table, causing all traffic to be blocked.
Add patches to allow VLAN setup even if VLAN filtering is disabled.
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
Currently, setting a bridge's self PVID to other value and deleting
the default VID 1 renders untagged ports of that VLAN unable to talk to
the CPU port:
bridge vlan add dev br0 vid 2 pvid untagged self
bridge vlan del dev br0 vid 1 self
bridge vlan add dev sw0p0 vid 2 pvid untagged
bridge vlan del dev sw0p0 vid 1
# br0 cannot send untagged frames out of sw0p0 anymore
That is because the CPU port is set to security mode and its PVID is
still 1, and untagged frames are dropped due to VLAN member violation.
Set the CPU port to fallback mode so untagged frames can pass through.
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
Remove dependencies on core kernel headers in host tools used to build perf,
which break on any non-linux system
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This patch adds support for 2 new uci sections.
config wifi-vlan
# iface is optional. if it is not defined the vlan will apply
# to all interfaces
option iface default_radio0
option name guest
option vid 100
option network guest
config wifi-station
# iface is optional. if it is not defined the station will apply
# to all interfaces
option iface default_radio0
# mac is optional. if it is not defined it will be a catch all
# for any sta using this key
option mac '00:11:22:33:44:55'
# vid is optional. if it is not defined, the sta will be part of
# the primary iface.
option vid 100
option key testtest
With this patch applied it is possible to use multiple PSKs on a single BSS.
Signed-off-by: John Crispin <john@phrozen.org>
db275e1 interface-ip: fix build on non-linux systems
3392046 system-dummy: fix missing return
a56b457 netifd: wireless: add support for tracking wifi-station sections
4ce33ce netifd: wireless: add support for tracking wifi-vlan sections
Signed-off-by: John Crispin <john@phrozen.org>
MAC address is set in board.d script
Interface swapping is not needed anymore as switching to DSA breaks
previous configuration anyway
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
eth0 has HW MAC address while eth2 does not.
Use eth0 instead so we don't have to set LAN MAC manually.
Disable unused eth2, until multi CPU port is supported.
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
Update network/LED configuration for DSA driver.
sysupgrade from images prior to this commit with config preserved
will break the ethernet.
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
Last reports with kernel 5.4 have all been positive [1], so let's open
this to a wider range of testers.
[1] https://github.com/openwrt/openwrt/pull/2804
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This is useful when booting OpenWrt from ramdisks in order to have both
images partitions defined.
Furthermore, instead of always using img2 for the inactive image, let's use
img1 or img2 accordingly.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Previously the dts were using a value determined by empirical testing,
because of a spi driver/clock bug. The bug was fixed quite some time
ago. 33 MHz is the default clock frequency used by RouterBOOT and thus
safe.
Signed-off-by: Tobias Schramm <t.schramm@manjaro.org>
Add kmod for the ST LSM6DSX IMU driver.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
[fixed missing regmap module dependencies]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Update the can-mcp251x-convert-to-half-duplex-SPI patch to fix reception
Some SPI host controllers such as the Cavium Thunder TX do not support
full-duplex SPI. Using half-duplex transfers allows the driver to work
with those host controllers.
This patch fixes the fact that mcp251x_hw_rx_frame was still relying on
a full-duplex transfer where bits were being shifted on MOSI at the same time
as MISO. After splitting the transaction into a spi_write_then_read() care
must be taken to ignore the first byte.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
- add fxos8700 support to GW52xx/GW53xx/GW54xx
- add USB_OTG support to GW552x
- add LSM9DS1 IMU support to GW560x
- add LSM9DS1 IMU support to GW5904
- add CC1352 UART to GW5910
- add BCM4330 support to GW5910
- fix wlan regulator for GW5910
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
32-bit x86 fail to compile fast-math feature when compiled with frame
pointer, which uses a register used in a couple of inline asm functions.
Previous versions of wolfssl had this by default. Keeping an extra
register available may increase performance, so it's being restored for
all architectures.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
This will be moved to packages:
https://github.com/openwrt/packages/pull/12378
Signed-off-by: Rosen Penev <rosenp@gmail.com>
[commit subject facelift]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Does not seem to be needed here. This will be imported into packages.
Ref: https://github.com/openwrt/packages/pull/12256
Signed-off-by: Rosen Penev <rosenp@gmail.com>
[subject facelift, PR ref]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
No package in base uses libconfig. Everything is in the packages feed.
Ref: https://github.com/openwrt/packages/pull/12255
Signed-off-by: Rosen Penev <rosenp@gmail.com>
[subject facelift, PR ref]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Since commit 910df3f06c we have build in
on all X86/64 platforms the gpio-it87 driver.
Since this change I am getting the following error message on boot.
> kern.err kernel: [ 1.009416] gpio_it87: no device
I do not have this device on my system. To prevent the nonsensical
message and the loading of the module I have added this as a package, so
that it can be installed later or during image building.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Reviewed-by: Philip Prindeville <philipp@redfish-solutions.com>
This is only a cosmetic correction, as the driver works as expected.
However, the error message confuses users about a missing reset definition.
On a defered init we don't see the following error message now:
[ 0.078292] ar7200-usb-phy usb-phy: phy reset is missing
Tested-by: Lech Perczak <lech.perczak@gmail.com>
Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de>
Due to filesystem write caching the old configuration data could stay
out of flash for a long time during a first boot after the sysupgrade.
Power loss during this period could damage the overlay data and even
make device inaccessable via the network.
Fix this by syncing data to a flash as soon as the previous
configuration will be unpacked after the sysupgrade. Also sync the FS
state after the sysupgrade.tgz archive removing to prevent duplicative
extraction of a previous configuration.
Tested with AMD Geode based board.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
This commit removes changes from upstream commits:
8e18c8e58da6 arm64: dts: marvell: armada-3720-espressobin: declare SATA
PHY property
bd3d25b07342 arm64: dts: marvell: armada-37xx: link USB hosts with their
PHYs
For most boards which have factory bootloader this caused that devices
connected to USB 3.0 and SATA port were not detected. For them to
function users would need to upgrade the bootloader to version with ARM
Trusted Firmware 2.1 or later. Unfortunately there is no official
bootloader image with updated ATF component, therefore drop these
properties from nodes. This change was also tested briefly with
bootloader with updated ATF and the ports functioned properly.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Stijn Tintel
Hans Dedecker
Toke Høiland-Jørgensen
Kevin Darbyshire-Bryant
DENG Qingfang
Paul Spooren
Rafał Miłecki
Felix Fietkau
John Crispin
Adrian Schmutzler
Álvaro Fernández Rojas
Tobias Schramm
Petr Štetiar
Sungbo Eo
Tim Harvey
Eneas U de Queiroz
Rosen Penev
Florian Eckert
Johann Neuhauser
Sergey Ryazanov
Sven Roederer
Tomasz Maciej Nowak
Michael Heimpold